2016-12-26 4:19 GMT+09:00 Krzysztof Kozlowski <krzk@xxxxxxxxxx>:
> On Fri, Dec 23, 2016 at 01:24:47PM +0100, Marek Szyprowski wrote:
>> Add support for special property "samsung,off-state", which indicates a special
>> state suitable for device's "sleep" state. Its pin values/properties should
>> match the configuration in power down mode. It indicates that pin controller
>> can notify runtime power management subsystem, that it is ready for runtime
>> suspend if its all pins are configured for such state. This in turn might
>> allow to turn respective power domain off to reduce power consumption.
>>
>> Signed-off-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
>> ---
>> Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt | 8 ++++++++
>> drivers/pinctrl/samsung/pinctrl-samsung.c | 4 ++++
>> drivers/pinctrl/samsung/pinctrl-samsung.h | 1 +
>> 3 files changed, 13 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
>> index b7bd2e12a269..354eea0e7798 100644
>> --- a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
>> +++ b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
>> @@ -105,6 +105,7 @@ Required Properties:
>> - samsung,pin-drv: Drive strength configuration.
>> - samsung,pin-pud-pdn: Pull up/down configuration in power down mode.
>> - samsung,pin-drv-pdn: Drive strength configuration in power down mode.
>> + - samsung,off-state: Mark this configuration as suitable for bank power off.
>>
>> The values specified by these config properties should be derived from the
>> hardware manual and these values are programmed as-is into the pin
>> @@ -113,6 +114,13 @@ Required Properties:
>> Note: A child should include atleast a pin function selection property or
>> pin configuration property (one or more) or both.
>>
>> + Note: Special property "samsung,off-state" indicates that this state can
>> + be used for device's "sleep" pins state. Its pin values/properties should
>> + match the configuration in power down mode.
>
> Why power down values cannot be used for sleep state? Why you need
> separate pin control state? If pins values should match power down
> configuration, then they could just be added to default state, couldn't
> they?
>
> In the patch 2/9, existing configuration:
> 716 i2s0_bus: i2s0-bus {
> (...)
> 719 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
> 720 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> 721 samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
> 722 };
>
> additional configuration:
> + i2s0_bus_slp: i2s0-bus-slp {
> + samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
> + samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
> + samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
> + samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
> + samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
> + samsung,off-state;
> + };
+1
If I'm not missing something, it should be reasonably easy to
determine if a state is suitable for power off by its configuration,
by comparing pin-function and pin-pud with pin-con-pdn and
pin-pud-pdn.
Best regards,
Tomasz
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
