On Wed, Dec 14, 2016 at 03:04:04PM +0900, Hoegeun Kwon wrote:
> This patch add support for MIPI-DSI based S6E3HA2 AMOLED panel
> driver. This panel has 1440x2560 resolution in 5.7-inch physical
> panel in the TM2 device.
>
> Signed-off-by: Donghwa Lee <dh09.lee@xxxxxxxxxxx>
> Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx>
> Signed-off-by: Hoegeun Kwon <hoegeun.kwon@xxxxxxxxxxx>
> ---
> .../bindings/display/panel/samsung,s6e3ha2.txt | 52 ++
> drivers/gpu/drm/panel/Kconfig | 6 +
> drivers/gpu/drm/panel/Makefile | 1 +
> drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c | 756 +++++++++++++++++++++
> 4 files changed, 815 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> create mode 100644 drivers/gpu/drm/panel/panel-samsung-s6e3ha2.c
>
> diff --git a/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> new file mode 100644
> index 0000000..1f41f24
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/panel/samsung,s6e3ha2.txt
> @@ -0,0 +1,52 @@
> +Samsung S6E3HA2 5.7" 1440x2560 AMOLED panel
> +
> +Required properties:
> + - compatible: "samsung,s6e3ha2"
> + - reg: the virtual channel number of a DSI peripheral
> + - vdd3-supply: core voltage supply
> + - vci-supply: voltage supply for analog circuits
> + - reset-gpios: a GPIO spec for the reset pin
> + - enable-gpios: a GPIO spec for the panel enable pin
> + - te-gpios: a GPIO spec for the tearing effect synchronization signal gpio pin
Need to specify the GPIOs as active high or low.
> +
> +Optional properties:
> + - display-timings: timings for the connected panel as described by [1]
> +
> +The device node can contain one 'port' child node with one child
> +'endpoint' node, according to the bindings defined in [2]. This
> +node should describe panel's video bus.
> +
> +[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt
> +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
> +
> +Example:
> +
> + panel@0 {
> + compatible = "samsung,s6e3ha2";
> + reg = <0>;
reg doesn't really work here unless this node is a child of the DSI
controller node. But if it is a child node, then you don't need the OF
graph.
> + vdd3-supply = <&ldo27_reg>;
> + vci-supply = <&ldo28_reg>;
> + reset-gpios = <&gpg0 0 GPIO_ACTIVE_HIGH>;
> + enable-gpios = <&gpf1 5 GPIO_ACTIVE_HIGH>;
> + te-gpios = <&gpf1 3 GPIO_ACTIVE_HIGH>;
> +
> + display-timings {
> + timing-0 {
> + clock-frequency = <0>;
> + hactive = <1440>;
> + vactive = <2560>;
> + hfront-porch = <1>;
> + hback-porch = <1>;
> + hsync-len = <1>;
> + vfront-porch = <1>;
> + vback-porch = <15>;
> + vsync-len = <1>;
> + };
> + };
> +
> + port {
> + dsi_in: endpoint {
> + remote-endpoint = <&dsi_out>;
> + };
> + };
> + };
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
