Re: [PATCH 5/7] arm64: dts: exynos: Add dts files for Samsung Exynos5433 64bit SoC

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Krzysztof,

On 2016년 08월 16일 19:29, Krzysztof Kozlowski wrote:
> Hi Chanwoo,
> 
> Thanks for the patch and for squashing all contributions into one. I
> know that this removes individuals from authors but it makes development
> consistent. Of course I don't mind splitting things if they are sent
> separately following convention of "release early, release often".
> 
> I have just few minor nits, nothing important. I'll review the boards a
> little bit later because of other taks.
> 
> On 08/16/2016 08:35 AM, Chanwoo Choi wrote:
>> This patch adds new Exynos5433 dtsi to support 64-bit Exynos5433 SoC based on
>> Octa-core CPUs (quad Cortex-A57 and quad Cortex-A53). And Exynos5433 supports
>> PSCI (Power State Coordination Interface) v0.1.
>>
>> This patch includes following Device Tree node to support Exynos5433 SoC:
>> 1. Octa cores for big.LITTLE architecture
>> - Cortex-A53 LITTLE Quad-core
>> - Cortex-A57 big Quad-core
>> - Support PSCI v0.1
>>
>> 2. Clock controller node
>> - CMU_TOP   : clocks for IMEM/FSYS/G3D/GSCL/HEVC/MSCL/G2D/MFC/PERIC/PERIS
>> - CMU_CPIF  : clocks for LLI (Low Latency Interface)
>> - CMU_MIF   : clocks for DRAM Memory Controller
>> - CMU_PERIC : clocks for UART/I2C/SPI/I2S/PCM/SPDIF/PWM/SLIMBUS
>> - CMU_PERIS : clocks for PMU/TMU/MCT/WDT/RTC/SECKEY/TZPC
>> - CMU_FSYS  : clocks for USB/UFS/SDMMC/TSI/PDMA
>> - CMU_G2D   : clocks for G2D/MDMA
>> - CMU_DISP  : clocks for DECON/HDMI/DSIM/MIXER
>> - CMU_AUD   : clocks for Cortex-A5/BUS/AUDIO
>> - CMU_BUS{0|1|2} : clocks for global data buses and global peripheral buses
>> - CMU_G3D   : clocks for 3D Graphics Engine
>> - CMU_GSCL  : clocks for GSCALER
>> - CMU_APOLLO: clocks for Cortex-A53 Quad-core processor.
>> - CMU_ATLAS : clocks for Cortex-A57 Quad-core processor,
>>               CoreSight and L2 cache controller.
>> - CMU_MSCL  : clocks for M2M (Memory to Memory) scaler and JPEG IPs.
>> - CMU_MFC   : clocks for MFC (Multi-Format Codec) IP.
>> - CMU_HEVC  : clocks for HEVC(High Efficiency Video Codec) decoder IP.
>> - CMU_ISP   : clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs.
>> - CMU_CAM0  : clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} IPs.
>> - CMU_CAM1  : clocks for COrtex-A5/MIPI_CSIS2/FIMC_LITE_C/FIMC-FD IPs.
>>
>> 3. pinctrl node for GPIO
>> - alive/aud/cpif/ese/finger/fsys/imem/nfc/peric/touch pad
>>
>> 4. Timer
>> - ARM architecture timer (armv8-timer)
>> - MCT (Multi Core Timer) timer
>>
>> 5. Interrupt controller (GIC-400)
>>
>> 6. BUS devices
>> - HS-I2C (High-Speed I2C) device
>> - SPI (Serial Peripheral Interface) device
>>
>> 7. Sound devices
>> - I2S bus
>> - LPASS (Low Power Audio Subsystem)
>>
>> 8. Power management devices
>> - CPUFREQ for for Cortex-A53/A57
>> - TMU (Thermal Management Unit) for Cortex-A53/A57, G3D, ISP
>>
>> 9. Display controller devices
>> - DECON (Display and enhancement controller) for panel output
>> - DSI (Display Serial Interface)
>> - MIC (Mobile Image Compressor)
>> - IOMMU for GSCL/DECON/TV/MFC/JPEG/FLITE/3AA/FIMC
>>
>> 10. USB
>> - USB 3.0 DRD (Dual Role Device) controller
>> - USB 3.0 Host controller
>>
>> 11. Storage devices
>> - MSHC (Mobile Stoarage Host Controller)
>>
>> 12. Misc devices
>> - UART device
>> - ADC (Analog Digital Converter)
>> - PWM (Pulse Width Modulation)
>> - ADMA (Advanced DMA) and PDMA (Peripheral DMA)
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim@xxxxxxxxxxx>
>> Signed-off-by: Joonyoung Shim <jy0922.shim@xxxxxxxxxxx>
>> Signed-off-by: Inki Dae <inki.dae@xxxxxxxxxxx>
>> Signed-off-by: Jonghwa Lee <jonghwa3.lee@xxxxxxxxxxx>
>> Signed-off-by: Beomho Seo <beomho.seo@xxxxxxxxxxx>
>> Signed-off-by: Jaewon Kim <jaewon02.kim@xxxxxxxxxxx>
>> Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx>
>> Signed-off-by: Inha Song <ideal.song@xxxxxxxxxxx>
>> Signed-off-by: Ingi kim <ingi2.kim@xxxxxxxxxxx>
>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>> Signed-off-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
>> Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx>
>> ---
>>  arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi |  794 ++++++++++
>>  .../dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi |   23 +
>>  .../dts/exynos/exynos5433-tmu-sensor-conf.dtsi     |   22 +
>>  arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi     |  306 ++++
>>  arch/arm64/boot/dts/exynos/exynos5433.dtsi         | 1580 ++++++++++++++++++++
>>  5 files changed, 2725 insertions(+)
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
>>  create mode 100644 arch/arm64/boot/dts/exynos/exynos5433.dtsi
>>
>> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
>> new file mode 100644
>> index 000000000000..2bf94face3f7
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
>> @@ -0,0 +1,794 @@
>> +/*
>> + * Samsung's Exynos5433 SoC pin-mux and pin-config device tree source
>> + *
>> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
>> + * Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> + *
>> + * Samsung's Exynos5433 SoC pin-mux and pin-config options are listed as device
>> + * tree nodes are listed in this file.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#define PIN_PULL_NONE		0
>> +#define PIN_PULL_DOWN		1
>> +#define PIN_PULL_UP		3
>> +
>> +#define PIN_DRV_LV1		0
>> +#define PIN_DRV_LV2		2
>> +#define PIN_DRV_LV3		1
>> +#define PIN_DRV_LV4		3
>> +
>> +#define PIN_IN			0
>> +#define PIN_OUT			1
>> +#define PIN_FUNC1		2
>> +
>> +#define PIN(_func, _pin, _pull, _drv)			\
>> +	_pin {						\
>> +		samsung,pins = #_pin;			\
>> +		samsung,pin-function = <PIN_ ##_func>;	\
>> +		samsung,pin-pud = <PIN_PULL_ ##_pull>;	\
>> +		samsung,pin-drv = <PIN_DRV_ ##_drv>;	\
>> +	}
>> +
>> +&pinctrl_alive {
>> +	gpa0: gpa0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		interrupt-parent = <&gic>;
>> +		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
>> +				<0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpa1: gpa1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		interrupt-parent = <&gic>;
>> +		interrupts = <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
>> +				<0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpa2: gpa2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpa3: gpa3 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpf1: gpf1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpf2: gpf2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpf3: gpf3 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpf4: gpf4 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpf5: gpf5 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +};
>> +
>> +&pinctrl_aud {
>> +	gpz0: gpz0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpz1: gpz1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	i2s0_bus: i2s0-bus {
>> +		samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3",
>> +				"gpz0-4", "gpz0-5", "gpz0-6";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pcm0_bus: pcm0-bus {
>> +		samsung,pins = "gpz1-0", "gpz1-1", "gpz1-2", "gpz1-3";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	uart_aud_bus: uart-aud-bus {
>> +		samsung,pins = "gpz1-3", "gpz1-2", "gpz1-1", "gpz1-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +};
>> +
>> +&pinctrl_cpif {
>> +	gpv6: gpv6 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +};
>> +
>> +&pinctrl_ese {
>> +	gpj2: gpj2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +};
>> +
>> +&pinctrl_finger {
>> +	gpd5: gpd5 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	spi2_bus: spi2-bus {
>> +		samsung,pins = "gpd5-0", "gpd5-2", "gpd5-3";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c6_bus: hs-i2c6-bus {
>> +		samsung,pins = "gpd5-3", "gpd5-2";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
> 
> Unnecessary blank line.

I'll remove it.

> 
>> +};
>> +
>> +&pinctrl_fsys {
>> +	gph1: gph1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpr4: gpr4 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpr0: gpr0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpr1: gpr1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpr2: gpr2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpr3: gpr3 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +	sd0_clk: sd0-clk {
>> +		samsung,pins = "gpr0-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_cmd: sd0-cmd {
>> +		samsung,pins = "gpr0-1";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_rdqs: sd0-rdqs {
>> +		samsung,pins = "gpr0-2";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_qrdy: sd0-qrdy {
>> +		samsung,pins = "gpr0-3";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_bus1: sd0-bus-width1 {
>> +		samsung,pins = "gpr1-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_bus4: sd0-bus-width4 {
>> +		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd0_bus8: sd0-bus-width8 {
>> +		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd1_clk: sd1-clk {
>> +		samsung,pins = "gpr2-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd1_cmd: sd1-cmd {
>> +		samsung,pins = "gpr2-1";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd1_bus1: sd1-bus-width1 {
>> +		samsung,pins = "gpr3-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd1_bus4: sd1-bus-width4 {
>> +		samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd1_bus8: sd1-bus-width8 {
>> +		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	pcie_bus: pcie_bus {
>> +		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <3>;
>> +	};
>> +
>> +	sd2_clk: sd2-clk {
>> +		samsung,pins = "gpr4-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd2_cmd: sd2-cmd {
>> +		samsung,pins = "gpr4-1";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd2_cd: sd2-cd {
>> +		samsung,pins = "gpr4-2";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd2_bus1: sd2-bus-width1 {
>> +		samsung,pins = "gpr4-3";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd2_bus4: sd2-bus-width4 {
>> +		samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <3>;
>> +	};
>> +
>> +	sd2_clk_output: sd2-clk-output {
>> +		samsung,pins = "gpr4-0";
>> +		samsung,pin-function = <1>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <2>;
>> +	};
>> +
>> +	sd2_cmd_output: sd2-cmd-output {
>> +		samsung,pins = "gpr4-1";
>> +		samsung,pin-function = <1>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <2>;
>> +	};
>> +};
>> +
>> +&pinctrl_imem {
>> +	gpf0: gpf0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +};
>> +
>> +&pinctrl_nfc {
>> +	gpj0: gpj0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	hs_i2c4_bus: hs-i2c4-bus {
>> +		samsung,pins = "gpj0-1", "gpj0-0";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
> 
> Ditto

I'll remove it.

> 
>> +};
>> +
>> +&pinctrl_peric {
>> +	gpv7: gpv7 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpb0: gpb0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpc0: gpc0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpc1: gpc1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpc2: gpc2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpc3: gpc3 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpg0: gpg0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd0: gpd0 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd1: gpd1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd2: gpd2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd4: gpd4 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd8: gpd8 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd6: gpd6 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpd7: gpd7 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpg1: gpg1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpg2: gpg2 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	gpg3: gpg3 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	hs_i2c8_bus: hs-i2c8-bus {
>> +		samsung,pins = "gpb0-1", "gpb0-0";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c9_bus: hs-i2c9-bus {
>> +		samsung,pins = "gpb0-3", "gpb0-2";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	i2s1_bus: i2s1-bus {
>> +		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
>> +				"gpd4-3", "gpd4-4";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pcm1_bus: pcm1-bus {
>> +		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
>> +				"gpd4-3", "gpd4-4";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	spdif_bus: spdif-bus {
>> +		samsung,pins = "gpd4-3", "gpd4-4";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <1>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_spi_pin0: fimc-is-spi-pin0 {
>> +		samsung,pins = "gpc3-3", "gpc3-2", "gpc3-1", "gpc3-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_spi_pin1: fimc-is-spi-pin1 {
>> +		samsung,pins = "gpc3-7", "gpc3-6", "gpc3-5", "gpc3-4";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	uart0_bus: uart0-bus {
>> +		samsung,pins = "gpd0-3", "gpd0-2", "gpd0-1", "gpd0-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +	};
>> +
>> +	hs_i2c2_bus: hs-i2c2-bus {
>> +		samsung,pins = "gpd0-3", "gpd0-2";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	uart2_bus: uart2-bus {
>> +		samsung,pins = "gpd1-5", "gpd1-4";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +	};
>> +
>> +	uart1_bus: uart1-bus {
>> +		samsung,pins = "gpd1-3", "gpd1-2", "gpd1-1", "gpd1-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +	};
>> +
>> +	hs_i2c3_bus: hs-i2c3-bus {
>> +		samsung,pins = "gpd1-3", "gpd1-2";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
> 
> Ditto

I'll remove it.

> 
>> +
>> +	hs_i2c0_bus: hs-i2c0-bus {
>> +		samsung,pins = "gpd2-1", "gpd2-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c1_bus: hs-i2c1-bus {
>> +		samsung,pins = "gpd2-3", "gpd2-2";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pwm0_out: pwm0-out {
>> +		samsung,pins = "gpd2-4";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pwm1_out: pwm1-out {
>> +		samsung,pins = "gpd2-5";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pwm2_out: pwm2-out {
>> +		samsung,pins = "gpd2-6";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	pwm3_out: pwm3-out {
>> +		samsung,pins = "gpd2-7";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	spi1_bus: spi1-bus {
>> +		samsung,pins = "gpd6-2", "gpd6-4", "gpd6-5";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c7_bus: hs-i2c7-bus {
>> +		samsung,pins = "gpd2-7", "gpd2-6";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	spi0_bus: spi0-bus {
>> +		samsung,pins = "gpd8-0", "gpd6-0", "gpd6-1";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c10_bus: hs-i2c10-bus {
>> +		samsung,pins = "gpg3-1", "gpg3-0";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	hs_i2c11_bus: hs-i2c11-bus {
>> +		samsung,pins = "gpg3-3", "gpg3-2";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	spi3_bus: spi3-bus {
>> +		samsung,pins = "gpg3-4", "gpg3-6", "gpg3-7";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	spi4_bus: spi4-bus {
>> +		samsung,pins = "gpv7-1", "gpv7-3", "gpv7-4";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_uart: fimc-is-uart {
>> +		samsung,pins = "gpc1-1", "gpc0-7";
>> +		samsung,pin-function = <3>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch0_i2c: fimc-is-ch0_i2c {
>> +		samsung,pins = "gpc2-1", "gpc2-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch0_mclk: fimc-is-ch0_mclk {
>> +		samsung,pins = "gpd7-0";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch1_i2c: fimc-is-ch1-i2c {
>> +		samsung,pins = "gpc2-3", "gpc2-2";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch1_mclk: fimc-is-ch1-mclk {
>> +		samsung,pins = "gpd7-1";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch2_i2c: fimc-is-ch2-i2c {
>> +		samsung,pins = "gpc2-5", "gpc2-4";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +
>> +	fimc_is_ch2_mclk: fimc-is-ch2-mclk {
>> +		samsung,pins = "gpd7-2";
>> +		samsung,pin-function = <2>;
>> +		samsung,pin-pud = <0>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +};
>> +
>> +&pinctrl_touch {
>> +	gpj1: gpj1 {
>> +		gpio-controller;
>> +		#gpio-cells = <2>;
>> +
>> +		interrupt-controller;
>> +		#interrupt-cells = <2>;
>> +	};
>> +
>> +	hs_i2c5_bus: hs-i2c5-bus {
>> +		samsung,pins = "gpj1-1", "gpj1-0";
>> +		samsung,pin-function = <4>;
>> +		samsung,pin-pud = <3>;
>> +		samsung,pin-drv = <0>;
>> +	};
>> +};
> 
> 
> (...)
> 
>> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
>> new file mode 100644
>> index 000000000000..175121db367e
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
>> @@ -0,0 +1,306 @@
>> +/*
>> + * Device tree sources for Exynos5433 thermal zone
>> + *
>> + * Copyright (c) 2016 Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <dt-bindings/thermal/thermal.h>
>> +
>> +/ {
>> +thermal-zones {
>> +	atlas0_thermal: atlas0-thermal {
>> +		thermal-sensors = <&tmu_atlas0>;
>> +		polling-delay-passive = <0>;
>> +		polling-delay = <0>;
>> +		trips {
>> +			atlas0_alert_0: atlas0-alert-0 {
>> +				temperature = <50000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_1: atlas0-alert-1 {
>> +				temperature = <55000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_2: atlas0-alert-2 {
>> +				temperature = <60000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_3: atlas0-alert-3 {
>> +				temperature = <70000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_4: atlas0-alert-4 {
>> +				temperature = <80000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_5: atlas0-alert-5 {
>> +				temperature = <90000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas0_alert_6: atlas0-alert-6 {
>> +				temperature = <95000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
> 
> No critical trip? I think it might be useful to shutdown the system in a
> user-friendly way.

When I use the critical trip, the following event occur[1].
But, I guess that this temperature is not correct temperature
because after completing the kernel booting, the temperature of big.LITTLE/G3D
are normal when checking the /sys/class/thermal/thermal_zoneX/temp right after booting.
- Maintain a uniform temperature(38 ~ 45 millicelsius) right after kernel booting.

I guess that the critical interrupt may occur before initializing the exynos tmu.
But, I don't spend the many time to check the exynos-tmu.c driver.

[1]
[  445.122122] thermal thermal_zone0: critical temperature reached(108 C),shutting down
[  445.122399] exynos-tmu 10060000.tmu: Temperature sensor ID: 0xa
[  445.122588] exynos-tmu 10060000.tmu: Calibration type is 2-point calibration
[  445.127942] reboot: Failed to start orderly shutdown: forcing the issue
[  445.134586] Emergency Sync complete
[    1.097954] reboot: Power down

> 
>> +		};
>> +
>> +		cooling-maps {
>> +			map0 {
>> +				/* Set maximum frequency as 1800MHz  */
>> +				trip = <&atlas0_alert_0>;
>> +				cooling-device = <&cpu4 1 1>;
> 
> Out of curiosity: why choosing specific cooling level (so quite fast
> the device will slow down) instead of letting cooling framework to
> decide how much to cool? Any particular reason behind this?

This cooling level is just default value in cooling-maps.
This value is able to overwrite on dts file. 

And the thermal subsystem support the cpu cooling features
with 'cooling-maps'.

Also, when I tested the performance and stress test
with GLBenchmark, the temperature of big.LITTLE cores/G3D
reach easily the critical temperature with 8 online cores.
So, I add the cooling level aggressively to protect
the system fault of CPU and GPU and to maintain
the system state.

> 
>> +			};
>> +			map1 {
>> +				/* Set maximum frequency as 1700MHz  */
>> +				trip = <&atlas0_alert_1>;
>> +				cooling-device = <&cpu4 2 2>;
>> +			};
>> +			map2 {
>> +				/* Set maximum frequency as 1600MHz  */
>> +				trip = <&atlas0_alert_2>;
>> +				cooling-device = <&cpu4 3 3>;
>> +			};
>> +			map3 {
>> +				/* Set maximum frequency as 1500MHz  */
>> +				trip = <&atlas0_alert_3>;
>> +				cooling-device = <&cpu4 4 4>;
>> +			};
>> +			map4 {
>> +				/* Set maximum frequency as 1400MHz  */
>> +				trip = <&atlas0_alert_4>;
>> +				cooling-device = <&cpu4 5 5>;
>> +			};
>> +			map5 {
>> +				/* Set maximum frequencyas 1200MHz  */
>> +				trip = <&atlas0_alert_5>;
>> +				cooling-device = <&cpu4 7 7>;
>> +			};
>> +			map6 {
>> +				/* Set maximum frequency as 800MHz  */
>> +				trip = <&atlas0_alert_6>;
>> +				cooling-device = <&cpu4 11 11>;
>> +			};
>> +		};
>> +	};
>> +
>> +	atlas1_thermal: atlas1-thermal {
>> +		thermal-sensors = <&tmu_atlas1>;
>> +		polling-delay-passive = <0>;
>> +		polling-delay = <0>;
>> +		trips {
>> +			atlas1_alert_0: atlas1-alert-0 {
>> +				temperature = <50000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_1: atlas1-alert-1 {
>> +				temperature = <55000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_2: atlas1-alert-2 {
>> +				temperature = <60000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_3: atlas1-alert-3 {
>> +				temperature = <70000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_4: atlas1-alert-4 {
>> +				temperature = <80000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_5: atlas1-alert-5 {
>> +				temperature = <90000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			atlas1_alert_6: atlas1-alert-6 {
>> +				temperature = <95000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
> 
> Same, critical trip point?
> 
>> +		};
>> +	};
>> +
>> +	g3d_thermal: g3d-thermal {
>> +		thermal-sensors = <&tmu_g3d>;
>> +		polling-delay-passive = <0>;
>> +		polling-delay = <0>;
>> +		trips {
>> +			g3d_alert_0: g3d-alert-0 {
>> +				temperature = <70000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_1: g3d-alert-1 {
>> +				temperature = <75000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_2: g3d-alert-2 {
>> +				temperature = <80000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_3: g3d-alert-3 {
>> +				temperature = <85000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_4: g3d-alert-4 {
>> +				temperature = <90000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_5: g3d-alert-5 {
>> +				temperature = <95000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			g3d_alert_6: g3d-alert-6 {
>> +				temperature = <100000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +		};
>> +	};
>> +
>> +	apollo_thermal: apollo-thermal {
>> +		thermal-sensors = <&tmu_apollo>;
>> +		polling-delay-passive = <0>;
>> +		polling-delay = <0>;
>> +		trips {
>> +			apollo_alert_0: apollo-alert-0 {
>> +				temperature = <50000>;	/* millicelsius */
>> +				hysteresis = <10000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_1: apollo-alert-1 {
>> +				temperature = <55000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_2: apollo-alert-2 {
>> +				temperature = <60000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_3: apollo-alert-3 {
>> +				temperature = <70000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_4: apollo-alert-4 {
>> +				temperature = <80000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_5: apollo-alert-5 {
>> +				temperature = <90000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			apollo_alert_6: apollo-alert-6 {
>> +				temperature = <95000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +		};
>> +
>> +		cooling-maps {
>> +			map0 {
>> +				/* Set maximum frequency as 1200MHz  */
>> +				trip = <&apollo_alert_0>;
>> +				cooling-device = <&cpu0 1 1>;
>> +			};
>> +			map1 {
>> +				/* Set maximum frequency as 1100MHz  */
>> +				trip = <&apollo_alert_1>;
>> +				cooling-device = <&cpu0 2 2>;
>> +			};
>> +			map2 {
>> +				/* Set maximum frequency as 1000MHz  */
>> +				trip = <&apollo_alert_2>;
>> +				cooling-device = <&cpu0 3 3>;
>> +			};
>> +			map3 {
>> +				/* Set maximum frequency as 900MHz  */
>> +				trip = <&apollo_alert_3>;
>> +				cooling-device = <&cpu0 4 4>;
>> +			};
>> +			map4 {
>> +				/* Set maximum frequency as 800MHz  */
>> +				trip = <&apollo_alert_4>;
>> +				cooling-device = <&cpu0 5 5>;
>> +			};
>> +			map5 {
>> +				/* Set maximum frequency as 700MHz  */
>> +				trip = <&apollo_alert_5>;
>> +				cooling-device = <&cpu0 6 6>;
>> +			};
>> +			map6 {
>> +				/* Set maximum frequency as 500MHz  */
>> +				trip = <&apollo_alert_6>;
>> +				cooling-device = <&cpu0 8 8>;
>> +			};
>> +		};
>> +	};
>> +
>> +	isp_thermal: isp-thermal {
>> +		thermal-sensors = <&tmu_isp>;
>> +		polling-delay-passive = <0>;
>> +		polling-delay = <0>;
>> +		trips {
>> +			isp_alert_0: isp-alert-0 {
>> +				temperature = <80000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_1: isp-alert-1 {
>> +				temperature = <85000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_2: isp-alert-2 {
>> +				temperature = <90000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_3: isp-alert-3 {
>> +				temperature = <95000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_4: isp-alert-4 {
>> +				temperature = <100000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_5: isp-alert-5 {
>> +				temperature = <105000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +			isp_alert_6: isp-alert-6 {
>> +				temperature = <110000>;	/* millicelsius */
>> +				hysteresis = <1000>;	/* millicelsius */
>> +				type = "active";
>> +			};
>> +		};
>> +	};
>> +};
>> +};
>> diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
>> new file mode 100644
>> index 000000000000..2a5b05744533
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
>> @@ -0,0 +1,1580 @@
>> +/*
>> + * Samsung's Exynos5433 SoC device tree source
>> + *
>> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
>> + *
>> + * Samsung's Exynos5433 SoC device nodes are listed in this file.
>> + * Exynos5433 based board files can include this file and provide
>> + * values for board specific bindings.
>> + *
>> + * Note: This file does not include device nodes for all the controllers in
>> + * Exynos5433 SoC. As device tree coverage for Exynos5433 increases,
>> + * additional nodes can be added to this file.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <dt-bindings/clock/exynos5433.h>
>> +
>> +/ {
>> +	compatible = "samsung,exynos5433";
>> +	#address-cells = <2>;
>> +	#size-cells = <2>;
>> +
>> +	interrupt-parent = <&gic>;
>> +
>> +	cpus {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +
>> +		cpu0: cpu@100 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x100>;
>> +			clock-frequency = <1300000000>;
>> +			clocks = <&cmu_apollo CLK_SCLK_APOLLO>;
>> +			clock-names = "apolloclk";
>> +			operating-points-v2 = <&cluster_a53_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu1: cpu@101 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x101>;
>> +			clock-frequency = <1300000000>;
>> +			operating-points-v2 = <&cluster_a53_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu2: cpu@102 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x102>;
>> +			clock-frequency = <1300000000>;
>> +			operating-points-v2 = <&cluster_a53_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu3: cpu@103 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a53", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x103>;
>> +			clock-frequency = <1300000000>;
>> +			operating-points-v2 = <&cluster_a53_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu4: cpu@0 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a57", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x0>;
>> +			clock-frequency = <1900000000>;
>> +			clocks = <&cmu_atlas CLK_SCLK_ATLAS>;
>> +			clock-names = "atlasclk";
>> +			operating-points-v2 = <&cluster_a57_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu5: cpu@1 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a57", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x1>;
>> +			clock-frequency = <1900000000>;
>> +			operating-points-v2 = <&cluster_a57_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu6: cpu@2 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a57", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x2>;
>> +			clock-frequency = <1900000000>;
>> +			operating-points-v2 = <&cluster_a57_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +
>> +		cpu7: cpu@3 {
>> +			device_type = "cpu";
>> +			compatible = "arm,cortex-a57", "arm,armv8";
>> +			enable-method = "psci";
>> +			reg = <0x3>;
>> +			clock-frequency = <1900000000>;
>> +			operating-points-v2 = <&cluster_a57_opp_table>;
>> +			#cooling-cells = <2>;
>> +		};
>> +	};
>> +
>> +	cluster_a53_opp_table: opp_table0 {
>> +		compatible = "operating-points-v2";
>> +		opp-shared;
>> +
>> +		opp@400000000 {
>> +			opp-hz = /bits/ 64 <400000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp@500000000 {
>> +			opp-hz = /bits/ 64 <500000000>;
>> +			opp-microvolt = <925000>;
>> +		};
>> +		opp@600000000 {
>> +			opp-hz = /bits/ 64 <600000000>;
>> +			opp-microvolt = <950000>;
>> +		};
>> +		opp@700000000 {
>> +			opp-hz = /bits/ 64 <700000000>;
>> +			opp-microvolt = <975000>;
>> +		};
>> +		opp@800000000 {
>> +			opp-hz = /bits/ 64 <800000000>;
>> +			opp-microvolt = <1000000>;
>> +		};
>> +		opp@900000000 {
>> +			opp-hz = /bits/ 64 <900000000>;
>> +			opp-microvolt = <1050000>;
>> +		};
>> +		opp@1000000000 {
>> +			opp-hz = /bits/ 64 <1000000000>;
>> +			opp-microvolt = <1075000>;
>> +		};
>> +		opp@1100000000 {
>> +			opp-hz = /bits/ 64 <1100000000>;
>> +			opp-microvolt = <1112500>;
>> +		};
>> +		opp@1200000000 {
>> +			opp-hz = /bits/ 64 <1200000000>;
>> +			opp-microvolt = <1112500>;
>> +		};
>> +		opp@1300000000 {
>> +			opp-hz = /bits/ 64 <1300000000>;
>> +			opp-microvolt = <1150000>;
>> +		};
>> +	};
>> +
>> +	cluster_a57_opp_table: opp_table1 {
>> +		compatible = "operating-points-v2";
>> +		opp-shared;
>> +
>> +		opp@500000000 {
>> +			opp-hz = /bits/ 64 <500000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp@600000000 {
>> +			opp-hz = /bits/ 64 <600000000>;
>> +			opp-microvolt = <900000>;
>> +		};
>> +		opp@700000000 {
>> +			opp-hz = /bits/ 64 <700000000>;
>> +			opp-microvolt = <912500>;
>> +		};
>> +		opp@800000000 {
>> +			opp-hz = /bits/ 64 <800000000>;
>> +			opp-microvolt = <912500>;
>> +		};
>> +		opp@900000000 {
>> +			opp-hz = /bits/ 64 <900000000>;
>> +			opp-microvolt = <937500>;
>> +		};
>> +		opp@1000000000 {
>> +			opp-hz = /bits/ 64 <1000000000>;
>> +			opp-microvolt = <975000>;
>> +		};
>> +		opp@1100000000 {
>> +			opp-hz = /bits/ 64 <1100000000>;
>> +			opp-microvolt = <1012500>;
>> +		};
>> +		opp@1200000000 {
>> +			opp-hz = /bits/ 64 <1200000000>;
>> +			opp-microvolt = <1037500>;
>> +		};
>> +		opp@1300000000 {
>> +			opp-hz = /bits/ 64 <1300000000>;
>> +			opp-microvolt = <1062500>;
>> +		};
>> +		opp@1400000000 {
>> +			opp-hz = /bits/ 64 <1400000000>;
>> +			opp-microvolt = <1087500>;
>> +		};
>> +		opp@1500000000 {
>> +			opp-hz = /bits/ 64 <1500000000>;
>> +			opp-microvolt = <1125000>;
>> +		};
>> +		opp@1600000000 {
>> +			opp-hz = /bits/ 64 <1600000000>;
>> +			opp-microvolt = <1137500>;
>> +		};
>> +		opp@1700000000 {
>> +			opp-hz = /bits/ 64 <1700000000>;
>> +			opp-microvolt = <1175000>;
>> +		};
>> +		opp@1800000000 {
>> +			opp-hz = /bits/ 64 <1800000000>;
>> +			opp-microvolt = <1212500>;
>> +		};
>> +		opp@1900000000 {
>> +			opp-hz = /bits/ 64 <1900000000>;
>> +			opp-microvolt = <1262500>;
>> +		};
>> +	};
>> +
>> +	psci {
>> +		compatible = "arm,psci";
>> +		method = "smc";
>> +		cpu_off = <0x84000002>;
>> +		cpu_on = <0xC4000003>;
>> +	};
>> +
>> +	reboot: syscon-reboot {
>> +		compatible = "syscon-reboot";
>> +		regmap = <&pmu_system_controller>;
>> +		offset = <0x400>;
>> +		mask = <0x1>;
>> +	};
>> +
>> +	soc: soc {
>> +		compatible = "simple-bus";
>> +		#address-cells = <1>;
>> +		#size-cells = <1>;
>> +		ranges = <0x0 0x0 0x0 0x18000000>;
>> +
>> +		chipid@10000000 {
>> +			compatible = "samsung,exynos4210-chipid";
>> +			reg = <0x10000000 0x100>;
>> +		};
>> +
>> +		xxti: xxti {
>> +			compatible = "fixed-clock";
>> +			clock-output-names = "oscclk";
>> +			#clock-cells = <0>;
>> +		};
>> +
>> +		cmu_top: clock-controller@10030000 {
>> +			compatible = "samsung,exynos5433-cmu-top";
>> +			reg = <0x10030000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_mphy_pll",
>> +				"sclk_mfc_pll",
>> +				"sclk_bus_pll";
>> +			clocks = <&xxti>,
>> +			       <&cmu_cpif CLK_SCLK_MPHY_PLL>,
>> +			       <&cmu_mif CLK_SCLK_MFC_PLL>,
>> +			       <&cmu_mif CLK_SCLK_BUS_PLL>;
>> +		};
>> +
>> +		cmu_cpif: clock-controller@10fc0000 {
>> +			compatible = "samsung,exynos5433-cmu-cpif";
>> +			reg = <0x10fc0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk";
>> +			clocks = <&xxti>;
>> +		};
>> +
>> +		cmu_mif: clock-controller@105b0000 {
>> +			compatible = "samsung,exynos5433-cmu-mif";
>> +			reg = <0x105b0000 0x2000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_mphy_pll";
>> +			clocks = <&xxti>,
>> +			       <&cmu_cpif CLK_SCLK_MPHY_PLL>;
> 
> Are these lines aligned? It looks not but maybe this is just my mail
> client. Also it looks that spaces are used for clocks property but not
> for clock-names.

I'll fix it by using only tab. The exynos5433.dtsi uses the 'space'
for aligned. It is my mistake. I'll only use the 'tab' instead of 'space'.

> 
>> +		};
>> +
>> +		cmu_peric: clock-controller@14c80000 {
>> +			compatible = "samsung,exynos5433-cmu-peric";
>> +			reg = <0x14c80000 0x1000>;
>> +			#clock-cells = <1>;
>> +		};
>> +
>> +		cmu_peris: clock-controller@0x10040000 {
>> +			compatible = "samsung,exynos5433-cmu-peris";
>> +			reg = <0x10040000 0x1000>;
>> +			#clock-cells = <1>;
>> +		};
>> +
>> +		cmu_fsys: clock-controller@156e0000 {
>> +			compatible = "samsung,exynos5433-cmu-fsys";
>> +			reg = <0x156e0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_ufs_mphy",
>> +				"div_aclk_fsys_200",
>> +				"sclk_pcie_100_fsys",
>> +				"sclk_ufsunipro_fsys",
>> +				"sclk_mmc2_fsys",
>> +				"sclk_mmc1_fsys",
>> +				"sclk_mmc0_fsys",
>> +				"sclk_usbhost30_fsys",
>> +				"sclk_usbdrd30_fsys";
>> +			clocks = <&xxti>,
>> +			       <&cmu_cpif CLK_SCLK_UFS_MPHY>,
>> +			       <&cmu_top CLK_DIV_ACLK_FSYS_200>,
>> +			       <&cmu_top CLK_SCLK_PCIE_100_FSYS>,
>> +			       <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>,
>> +			       <&cmu_top CLK_SCLK_MMC2_FSYS>,
>> +			       <&cmu_top CLK_SCLK_MMC1_FSYS>,
>> +			       <&cmu_top CLK_SCLK_MMC0_FSYS>,
>> +			       <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
>> +			       <&cmu_top CLK_SCLK_USBDRD30_FSYS>;
> 
> Indentation looks like mixing spaces and tabs (or is it just my mail
> program?).

My mistake. I'll fix it.

> 
>> +		};
>> +
>> +		cmu_g2d: clock-controller@12460000 {
>> +			compatible = "samsung,exynos5433-cmu-g2d";
>> +			reg = <0x12460000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"aclk_g2d_266",
>> +				"aclk_g2d_400";
>> +			clocks = <&xxti>,
>> +			       <&cmu_top CLK_ACLK_G2D_266>,
>> +			       <&cmu_top CLK_ACLK_G2D_400>;
>> +		};
>> +
>> +		cmu_disp: clock-controller@13b90000 {
>> +			compatible = "samsung,exynos5433-cmu-disp";
>> +			reg = <0x13b90000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_dsim1_disp",
>> +				"sclk_dsim0_disp",
>> +				"sclk_dsd_disp",
>> +				"sclk_decon_tv_eclk_disp",
>> +				"sclk_decon_vclk_disp",
>> +				"sclk_decon_eclk_disp",
>> +				"sclk_decon_tv_vclk_disp",
>> +				"aclk_disp_333";
>> +			clocks = <&xxti>,
>> +			       <&cmu_mif CLK_SCLK_DSIM1_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DSIM0_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DSD_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DECON_VCLK_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DECON_ECLK_DISP>,
>> +			       <&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>,
>> +			       <&cmu_mif CLK_ACLK_DISP_333>;
> 
> ditto

I'll fix it.

> 
>> +		};
>> +
>> +		cmu_aud: clock-controller@114c0000 {
>> +			compatible = "samsung,exynos5433-cmu-aud";
>> +			reg = <0x114c0000 0x1000>;
>> +			#clock-cells = <1>;
>> +		};
>> +
>> +		cmu_bus0: clock-controller@13600000 {
>> +			compatible = "samsung,exynos5433-cmu-bus0";
>> +			reg = <0x13600000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "aclk_bus0_400";
>> +			clocks = <&cmu_top CLK_ACLK_BUS0_400>;
>> +		};
>> +
>> +		cmu_bus1: clock-controller@14800000 {
>> +			compatible = "samsung,exynos5433-cmu-bus1";
>> +			reg = <0x14800000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "aclk_bus1_400";
>> +			clocks = <&cmu_top CLK_ACLK_BUS1_400>;
>> +		};
>> +
>> +		cmu_bus2: clock-controller@13400000 {
>> +			compatible = "samsung,exynos5433-cmu-bus2";
>> +			reg = <0x13400000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "aclk_bus2_400";
>> +			clocks = <&xxti>, <&cmu_mif CLK_ACLK_BUS2_400>;
>> +		};
>> +
>> +		cmu_g3d: clock-controller@14aa0000 {
>> +			compatible = "samsung,exynos5433-cmu-g3d";
>> +			reg = <0x14aa0000 0x2000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "aclk_g3d_400";
>> +			clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>;
>> +		};
>> +
>> +		cmu_gscl: clock-controller@13cf0000 {
>> +			compatible = "samsung,exynos5433-cmu-gscl";
>> +			reg = <0x13cf0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"aclk_gscl_111",
>> +				"aclk_gscl_333";
>> +			clocks = <&xxti>,
>> +				<&cmu_top CLK_ACLK_GSCL_111>,
>> +				<&cmu_top CLK_ACLK_GSCL_333>;
>> +		};
>> +
>> +		cmu_apollo: clock-controller@11900000 {
>> +			compatible = "samsung,exynos5433-cmu-apollo";
>> +			reg = <0x11900000 0x2000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "sclk_bus_pll_apollo";
>> +			clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_APOLLO>;
>> +		};
>> +
>> +		cmu_atlas: clock-controller@11800000 {
>> +			compatible = "samsung,exynos5433-cmu-atlas";
>> +			reg = <0x11800000 0x2000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "sclk_bus_pll_atlas";
>> +			clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>;
>> +		};
>> +
>> +		cmu_mscl: clock-controller@105d0000 {
>> +			compatible = "samsung,exynos5433-cmu-mscl";
>> +			reg = <0x150d0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_jpeg_mscl",
>> +				"aclk_mscl_400";
>> +			clocks = <&xxti>,
>> +			       <&cmu_top CLK_SCLK_JPEG_MSCL>,
>> +			       <&cmu_top CLK_ACLK_MSCL_400>;
> 
> ditto

I'll fix it.

> 
>> +		};
>> +
>> +		cmu_mfc: clock-controller@15280000 {
>> +			compatible = "samsung,exynos5433-cmu-mfc";
>> +			reg = <0x15280000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "aclk_mfc_400";
>> +			clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>;
>> +		};
>> +
>> +		cmu_hevc: clock-controller@14f80000 {
>> +			compatible = "samsung,exynos5433-cmu-hevc";
>> +			reg = <0x14f80000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk", "aclk_hevc_400";
>> +			clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>;
>> +		};
>> +
>> +		cmu_isp: clock-controller@146d0000 {
>> +			compatible = "samsung,exynos5433-cmu-isp";
>> +			reg = <0x146d0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"aclk_isp_dis_400",
>> +				"aclk_isp_400";
>> +			clocks = <&xxti>,
>> +			       <&cmu_top CLK_ACLK_ISP_DIS_400>,
>> +			       <&cmu_top CLK_ACLK_ISP_400>;
> 
> ditto

I'll fix it.

> 
>> +		};
>> +
>> +		cmu_cam0: clock-controller@120d0000 {
>> +			compatible = "samsung,exynos5433-cmu-cam0";
>> +			reg = <0x120d0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"aclk_cam0_333",
>> +				"aclk_cam0_400",
>> +				"aclk_cam0_552";
>> +			clocks = <&xxti>,
>> +			       <&cmu_top CLK_ACLK_CAM0_333>,
>> +			       <&cmu_top CLK_ACLK_CAM0_400>,
>> +			       <&cmu_top CLK_ACLK_CAM0_552>;
> 
> ditto

I'll fix it.

> 
>> +		};
>> +
>> +		cmu_cam1: clock-controller@145d0000 {
>> +			compatible = "samsung,exynos5433-cmu-cam1";
>> +			reg = <0x145d0000 0x1000>;
>> +			#clock-cells = <1>;
>> +
>> +			clock-names = "oscclk",
>> +				"sclk_isp_uart_cam1",
>> +				"sclk_isp_spi1_cam1",
>> +				"sclk_isp_spi0_cam1",
>> +				"aclk_cam1_333",
>> +				"aclk_cam1_400",
>> +				"aclk_cam1_552";
>> +			clocks = <&xxti>,
>> +			       <&cmu_top CLK_SCLK_ISP_UART_CAM1>,
>> +			       <&cmu_top CLK_SCLK_ISP_SPI1_CAM1>,
>> +			       <&cmu_top CLK_SCLK_ISP_SPI0_CAM1>,
>> +			       <&cmu_top CLK_ACLK_CAM1_333>,
>> +			       <&cmu_top CLK_ACLK_CAM1_400>,
>> +			       <&cmu_top CLK_ACLK_CAM1_552>;
> 
> ditto

I'll fix it.

> 
>> +		};
>> +
>> +		tmu_atlas0: tmu@10060000 {
>> +			compatible = "samsung,exynos5433-tmu";
>> +			reg = <0x10060000 0x200>;
>> +			interrupts = <0 95 0>;
>> +			clocks = <&cmu_peris CLK_PCLK_TMU0_APBIF>,
>> +				 <&cmu_peris CLK_SCLK_TMU0>;
>> +			clock-names = "tmu_apbif", "tmu_sclk";
>> +			#include "exynos5433-tmu-sensor-conf.dtsi"
>> +			status = "disabled";
>> +		};
>> +
>> +		tmu_atlas1: tmu@10068000 {
>> +			compatible = "samsung,exynos5433-tmu";
>> +			reg = <0x10068000 0x200>;
>> +			interrupts = <0 96 0>;
>> +			clocks = <&cmu_peris CLK_PCLK_TMU0_APBIF>,
>> +				 <&cmu_peris CLK_SCLK_TMU0>;
>> +			clock-names = "tmu_apbif", "tmu_sclk";
>> +			#include "exynos5433-tmu-sensor-conf.dtsi"
>> +			status = "disabled";
>> +		};
>> +
>> +		tmu_g3d: tmu@10070000 {
>> +			compatible = "samsung,exynos5433-tmu";
>> +			reg = <0x10070000 0x200>;
>> +			interrupts = <0 99 0>;
>> +			clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
>> +				 <&cmu_peris CLK_SCLK_TMU1>;
>> +			clock-names = "tmu_apbif", "tmu_sclk";
>> +			#include "exynos5433-tmu-g3d-sensor-conf.dtsi"
>> +			status = "disabled";
>> +		};
>> +
>> +		tmu_apollo: tmu@10078000 {
>> +			compatible = "samsung,exynos5433-tmu";
>> +			reg = <0x10078000 0x200>;
>> +			interrupts = <0 115 0>;
>> +			clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
>> +				 <&cmu_peris CLK_SCLK_TMU1>;
>> +			clock-names = "tmu_apbif", "tmu_sclk";
>> +			#include "exynos5433-tmu-sensor-conf.dtsi"
>> +			status = "disabled";
>> +		};
>> +
>> +		tmu_isp: tmu@1007c000 {
>> +			compatible = "samsung,exynos5433-tmu";
>> +			reg = <0x1007c000 0x200>;
>> +			interrupts = <0 94 0>;
>> +			clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
>> +				 <&cmu_peris CLK_SCLK_TMU1>;
>> +			clock-names = "tmu_apbif", "tmu_sclk";
>> +			#include "exynos5433-tmu-sensor-conf.dtsi"
>> +			status = "disabled";
>> +		};
>> +
>> +		mct@101c0000 {
>> +			compatible = "samsung,exynos5433-mct",
> 
> Why 5433-mct compatible?

It is not necessary. I'll remove it.

> 
>> +				     "samsung,exynos4210-mct";
>> +			reg = <0x101c0000 0x800>;
>> +			interrupts = <0 102 0>, <0 103 0>, <0 104 0>, <0 105 0>,
>> +				<0 106 0>, <0 107 0>, <0 108 0>, <0 109 0>,
>> +				<0 110 0>, <0 111 0>, <0 112 0>, <0 113 0>;
>> +			clocks = <&xxti>,
>> +			         <&cmu_peris CLK_PCLK_MCT>;
>> +			clock-names = "fin_pll", "mct";
>> +		};
>> +
>> +		pinctrl_alive: pinctrl@10580000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x10580000 0x1A20>, <0x11090000 0x100>;
> 
> Can you switch to lowercase hex?	

OK.

> 
>> +
>> +			wakeup-interrupt-controller {
>> +				compatible = "samsung,exynos7-wakeup-eint";
>> +				interrupts = <0 16 0>;
>> +			};
>> +		};
>> +
>> +		pinctrl_aud: pinctrl@114b0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x114b0000 0x1000>;
>> +			interrupts = <0 68 0>;
>> +		};
>> +
>> +		pinctrl_cpif: pinctrl@10fe0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x10fe0000 0x1000>;
>> +			interrupts = <0 179 0>;
>> +		};
>> +
>> +		pinctrl_ese: pinctrl@14ca0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x14ca0000 0x1000>;
>> +			interrupts = <0 413 0>;
>> +		};
>> +
>> +		pinctrl_finger: pinctrl@14cb0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x14cb0000 0x1000>;
>> +			interrupts = <0 414 0>;
>> +		};
>> +
>> +		pinctrl_fsys: pinctrl@15690000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x15690000 0x1000>;
>> +			interrupts = <0 229 0>;
>> +		};
>> +
>> +		pinctrl_imem: pinctrl@11090000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x11090000 0x1000>;
>> +			interrupts = <0 325 0>;
>> +		};
>> +
>> +		pinctrl_nfc: pinctrl@14cd0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x14cd0000 0x1000>;
>> +			interrupts = <0 441 0>;
>> +		};
>> +
>> +		pinctrl_peric: pinctrl@14cc0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x14cc0000 0x1100>;
>> +			interrupts = <0 440 0>;
>> +		};
>> +
>> +		pinctrl_touch: pinctrl@14ce0000 {
>> +			compatible = "samsung,exynos5433-pinctrl";
>> +			reg = <0x14ce0000 0x1100>;
>> +			interrupts = <0 442 0>;
>> +		};
>> +
>> +		rtc: rtc@10590000 {
>> +			compatible = "samsung,exynos3250-rtc";
>> +			reg = <0x10590000 0x100>;
>> +			interrupts = <0 385 0>, <0 386 0>;
>> +			status = "disabled";
>> +		};
>> +
>> +		pmu_system_controller: system-controller@105c0000 {
>> +			compatible = "samsung,exynos5433-pmu", "syscon";
>> +			reg = <0x105c0000 0x5008>;
>> +			#clock-cells = <1>;
>> +			clock-names = "clkout16";
>> +			clocks = <&xxti>;
>> +		};
>> +
>> +		gic: interrupt-controller@11001000 {
>> +			compatible = "arm,gic-400";
>> +			#interrupt-cells = <3>;
>> +			interrupt-controller;
>> +			reg =	<0x11001000 0x1000>,
>> +				<0x11002000 0x2000>,
>> +				<0x11004000 0x2000>,
>> +				<0x11006000 0x2000>;
>> +			interrupts = <1 9 0xf04>;
>> +		};
>> +
>> +		lpass: lpass@11400000 {
>> +			compatible = "samsung,exynos5433-lpass";
>> +			reg = <0x11400000 0x100>;
>> +			samsung,pmu-syscon = <&pmu_system_controller>;
>> +			status = "disabled";
>> +		};
>> +
>> +		i2s0: i2s0@11440000 {
>> +			compatible = "samsung,exynos7-i2s";
>> +			reg = <0x11440000 0x100>;
>> +			dmas = <&adma 0 &adma 2>;
>> +			dma-names = "tx", "rx";
>> +			interrupts = <0 70 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_aud CLK_PCLK_AUD_I2S>,
>> +				 <&cmu_aud CLK_SCLK_AUD_I2S>,
>> +				 <&cmu_aud CLK_SCLK_I2S_BCLK>;
>> +			clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&i2s0_bus>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mipi_phy: video-phy@105C0708 {
>> +			compatible = "samsung,exynos5433-mipi-video-phy";
>> +			#phy-cells = <1>;
>> +			samsung,pmu-syscon = <&pmu_system_controller>;
>> +			samsung,cam0-sysreg = <&syscon_cam0>;
>> +			samsung,cam1-sysreg = <&syscon_cam1>;
>> +			samsung,disp-sysreg = <&syscon_disp>;
>> +		};
>> +
>> +		decon: decon@13800000 {
>> +			compatible = "samsung,exynos5433-decon";
>> +			reg = <0x13800000 0x2104>;
>> +			clocks = <&cmu_disp CLK_PCLK_DECON>,
>> +				 <&cmu_disp CLK_ACLK_DECON>,
>> +				 <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
>> +				 <&cmu_disp CLK_ACLK_XIU_DECON0X>,
>> +				 <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
>> +				 <&cmu_disp CLK_SCLK_DECON_VCLK>,
>> +				 <&cmu_disp CLK_SCLK_DECON_ECLK>;
>> +			clock-names = "pclk", "aclk_decon", "aclk_smmu_decon0x",
>> +				      "aclk_xiu_decon0x", "pclk_smmu_decon0x",
>> +				      "sclk_decon_vclk", "sclk_decon_eclk";
>> +			interrupt-names = "fifo", "vsync", "lcd_sys";
>> +			interrupts = <0 201 0>, <0 202 0>, <0 203 0>;
>> +			samsung,disp-sysreg = <&syscon_disp>;
>> +			status = "disabled";
>> +			iommus = <&sysmmu_decon0x>, <&sysmmu_decon1x>;
>> +			iommu-names = "m0", "m1";
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				port@0 {
>> +					reg = <0>;
>> +					decon_to_mic: endpoint {
>> +						remote-endpoint = <&mic_to_decon>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		dsi: dsi@13900000 {
>> +			compatible = "samsung,exynos5433-mipi-dsi";
>> +			reg = <0x13900000 0xC0>;
>> +			interrupts = <0 205 0>;
>> +			phys = <&mipi_phy 1>;
>> +			phy-names = "dsim";
>> +			clocks = <&cmu_disp CLK_PCLK_DSIM0>,
>> +				 <&cmu_disp CLK_PHYCLK_MIPIDPHY0_BITCLKDIV8>,
>> +				 <&cmu_disp CLK_PHYCLK_MIPIDPHY0_RXCLKESC0>,
>> +				 <&cmu_disp CLK_SCLK_RGB_VCLK_TO_DSIM0>,
>> +				 <&cmu_disp CLK_SCLK_DSIM0>;
>> +			clock-names = "bus_clk",
>> +				      "phyclk_mipidphy0_bitclkdiv8",
>> +				      "phyclk_mipidphy0_rxclkesc0",
>> +				      "sclk_rgb_vclk_to_dsim0",
>> +				      "sclk_mipi";
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				port@0 {
>> +					reg = <0>;
>> +					dsi_to_mic: endpoint {
>> +						remote-endpoint = <&mic_to_dsi>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		mic: mic@13930000 {
>> +			compatible = "samsung,exynos5433-mic";
>> +			reg = <0x13930000 0x48>;
>> +			clocks = <&cmu_disp CLK_PCLK_MIC0>,
>> +				 <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
>> +			clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
>> +			samsung,disp-syscon = <&syscon_disp>;
>> +			status = "disabled";
>> +
>> +			ports {
>> +				#address-cells = <1>;
>> +				#size-cells = <0>;
>> +
>> +				port@0 {
>> +					reg = <0>;
>> +					mic_to_decon: endpoint {
>> +						remote-endpoint = <&decon_to_mic>;
>> +					};
>> +				};
>> +
>> +				port@1 {
>> +					reg = <1>;
>> +					mic_to_dsi: endpoint {
>> +						remote-endpoint = <&dsi_to_mic>;
>> +					};
>> +				};
>> +			};
>> +		};
>> +
>> +		syscon_disp: syscon@13B80000 {
> 
> Here and everywhere below - lowercase hex please.

OK. I'll modify them.

> 
>> +			compatible = "samsung,exynos5433-sysreg", "syscon";
>> +			reg = <0x13B80000 0x1010>;
>> +		};
>> +
>> +		syscon_cam0: syscon@120F0000 {
>> +			compatible = "samsung,exynos5433-sysreg", "syscon";
>> +			reg = <0x120F0000 0x1020>;
>> +		};
>> +
>> +		syscon_cam1: syscon@145F0000 {
>> +			compatible = "samsung,exynos5433-sysreg", "syscon";
>> +			reg = <0x145F0000 0x1038>;
>> +		};
>> +
>> +		sysmmu_gscl0: sysmmu@0x13C80000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13C80000 0x1000>;
>> +			interrupts = <0 288 0>;
>> +			clock-names = "aclk", "pclk";
>> +			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL0>,
>> +				<&cmu_gscl CLK_PCLK_SMMU_GSCL0>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_gscl1: sysmmu@0x13C90000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13C90000 0x1000>;
>> +			interrupts = <0 290 0>;
>> +			clock-names = "aclk", "pclk";
>> +			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL1>,
>> +			       <&cmu_gscl CLK_PCLK_SMMU_GSCL1>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_gscl2: sysmmu@0x13CA0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13CA0000 0x1000>;
>> +			interrupts = <0 292 0>;
>> +			clock-names = "aclk", "pclk";
>> +			clocks = <&cmu_gscl CLK_ACLK_SMMU_GSCL2>,
>> +			       <&cmu_gscl CLK_PCLK_SMMU_GSCL2>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_decon0x: sysmmu@0x13A00000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13A00000 0x1000>;
>> +			interrupts = <0 192 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
>> +			       <&cmu_disp CLK_ACLK_SMMU_DECON0X>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_decon1x: sysmmu@0x13A10000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13A10000 0x1000>;
>> +			interrupts = <0 194 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_disp CLK_PCLK_SMMU_DECON1X>,
>> +			       <&cmu_disp CLK_ACLK_SMMU_DECON1X>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_tv0x: sysmmu@0x13A20000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13A20000 0x1000>;
>> +			interrupts = <0 214 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_disp CLK_PCLK_SMMU_TV0X>,
>> +			       <&cmu_disp CLK_ACLK_SMMU_TV0X>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_tv1x: sysmmu@0x13A30000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x13A30000 0x1000>;
>> +			interrupts = <0 216 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_disp CLK_PCLK_SMMU_TV1X>,
>> +			       <&cmu_disp CLK_ACLK_SMMU_TV1X>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_mfc_0: sysmmu@0x15200000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x15200000 0x1000>;
>> +			interrupts = <0 352 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_mfc CLK_PCLK_SMMU_MFC_0>,
>> +			       <&cmu_mfc CLK_ACLK_SMMU_MFC_0>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_mfc_1: sysmmu@0x15210000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x15210000 0x1000>;
>> +			interrupts = <0 354 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_mfc CLK_PCLK_SMMU_MFC_1>,
>> +			       <&cmu_mfc CLK_ACLK_SMMU_MFC_1>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_jpeg: sysmmu@0x15060000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x15060000 0x1000>;
>> +			interrupts = <0 408 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_mscl CLK_PCLK_SMMU_JPEG>,
>> +			       <&cmu_mscl CLK_ACLK_SMMU_JPEG>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_flite_a: sysmmu@0x12150000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x12150000 0x1000>;
>> +			interrupts = <0 128 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam0 CLK_PCLK_SMMU_LITE_A>,
>> +				<&cmu_cam0 CLK_ACLK_SMMU_LITE_A>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_flite_b: sysmmu@0x12160000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x12160000 0x1000>;
>> +			interrupts = <0 130 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam0 CLK_PCLK_SMMU_LITE_B>,
>> +				<&cmu_cam0 CLK_ACLK_SMMU_LITE_B>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_flite_d: sysmmu@0x12170000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x12170000 0x1000>;
>> +			interrupts = <0 132 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam0 CLK_PCLK_SMMU_LITE_D>,
>> +				<&cmu_cam0 CLK_ACLK_SMMU_LITE_D>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_3aa0: sysmmu@0x12180000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x12180000 0x1000>;
>> +			interrupts = <0 137 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam0 CLK_PCLK_SMMU_3AA0>,
>> +				<&cmu_cam0 CLK_ACLK_SMMU_3AA0>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_3aa1: sysmmu@0x121A0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x121A0000 0x1000>;
>> +			interrupts = <0 147 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam0 CLK_PCLK_SMMU_3AA1>,
>> +				<&cmu_cam0 CLK_ACLK_SMMU_3AA1>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_flite_c: sysmmu@0x142B0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x142B0000 0x1000>;
>> +			interrupts = <0 160 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam1 CLK_PCLK_SMMU_LITE_C>,
>> +				<&cmu_cam1 CLK_ACLK_SMMU_LITE_C>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_fd: sysmmu@0x142C0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x142C0000 0x1000>;
>> +			interrupts = <0 162 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_cam1 CLK_PCLK_SMMU_FD>,
>> +				<&cmu_cam1 CLK_ACLK_SMMU_FD>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_cpu: sysmmu@0x142D0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x142D0000 0x1000>;
>> +			interrupts = <0 169 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_ISPCPU>,
>> +				<&cmu_isp CLK_ACLK_SMMU_ISPCPU>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_isp: sysmmu@0x14320000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x14320000 0x1000>;
>> +			interrupts = <0 346 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_ISP>,
>> +				<&cmu_isp CLK_ACLK_SMMU_ISP>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_drc: sysmmu@0x14330000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x14330000 0x1000>;
>> +			interrupts = <0 338 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_DRC>,
>> +				<&cmu_isp CLK_ACLK_SMMU_DRC>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_scc: sysmmu@0x14340000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x14340000 0x1000>;
>> +			interrupts = <0 340 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_SCALERC>,
>> +				<&cmu_isp CLK_ACLK_SMMU_SCALERC>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_dis0: sysmmu@0x143A0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x143A0000 0x1000>;
>> +			interrupts = <0 342 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_DIS0>,
>> +				<&cmu_isp CLK_ACLK_SMMU_DIS0>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_dis1: sysmmu@0x143B0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x143B0000 0x1000>;
>> +			interrupts = <0 344 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_DIS1>,
>> +				<&cmu_isp CLK_ACLK_SMMU_DIS1>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_scp: sysmmu@0x143C0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x143C0000 0x1000>;
>> +			interrupts = <0 336 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_SCALERP>,
>> +				<&cmu_isp CLK_ACLK_SMMU_SCALERP>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		sysmmu_fimc_3dnr: sysmmu@0x143D0000 {
>> +			compatible = "samsung,exynos-sysmmu";
>> +			reg = <0x143D0000 0x1000>;
>> +			interrupts = <0 349 0>;
>> +			clock-names = "pclk", "aclk";
>> +			clocks = <&cmu_isp CLK_PCLK_SMMU_3DNR>,
>> +				<&cmu_isp CLK_ACLK_SMMU_3DNR>;
>> +			#iommu-cells = <0>;
>> +		};
>> +
>> +		serial_0: serial@14c10000 {
>> +			compatible = "samsung,exynos5433-uart";
>> +			reg = <0x14c10000 0x100>;
>> +			interrupts = <0 421 0>;
>> +			clocks = <&cmu_peric CLK_PCLK_UART0>,
>> +				<&cmu_peric CLK_SCLK_UART0>;
>> +			clock-names = "uart", "clk_uart_baud0";
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&uart0_bus>;
>> +			status = "disabled";
>> +		};
>> +
>> +		serial_1: serial@14c20000 {
>> +			compatible = "samsung,exynos5433-uart";
>> +			reg = <0x14c20000 0x100>;
>> +			interrupts = <0 422 0>;
>> +			clocks = <&cmu_peric CLK_PCLK_UART1>,
>> +				<&cmu_peric CLK_SCLK_UART1>;
>> +			clock-names = "uart", "clk_uart_baud0";
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&uart1_bus>;
>> +			status = "disabled";
>> +		};
>> +
>> +		serial_2: serial@14c30000 {
>> +			compatible = "samsung,exynos5433-uart";
>> +			reg = <0x14c30000 0x100>;
>> +			interrupts = <0 423 0>;
>> +			clocks = <&cmu_peric CLK_PCLK_UART2>,
>> +				<&cmu_peric CLK_SCLK_UART2>;
>> +			clock-names = "uart", "clk_uart_baud0";
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&uart2_bus>;
> 
> Just like rest of serials, this should be also disabled.

OK. I'll add it.

> 
>> +		};
>> +
>> +		serial_3: serial@11460000 {
>> +			compatible = "samsung,exynos5433-uart";
>> +			reg = <0x11460000 0x100>;
>> +			interrupts = <0 67 0>;
>> +			clocks = <&cmu_aud CLK_PCLK_AUD_UART>,
>> +				<&cmu_aud CLK_SCLK_AUD_UART>;
>> +			clock-names = "uart", "clk_uart_baud0";
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&uart_aud_bus>;
>> +			status = "disabled";
>> +		};
>> +
>> +		spi_0: spi@14d20000 {
>> +			compatible = "samsung,exynos5433-spi";
>> +			reg = <0x14d20000 0x100>;
>> +			interrupts = <0 432 0>;
>> +			dmas = <&pdma0 9>, <&pdma0 8>;
>> +			dma-names = "tx", "rx";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_peric CLK_PCLK_SPI0>,
>> +				<&cmu_peric CLK_SCLK_SPI0>,
>> +				<&cmu_peric CLK_SCLK_IOCLK_SPI0>;
>> +			clock-names = "spi", "spi_busclk0", "spi_ioclk";
>> +			samsung,spi-src-clk = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi0_bus>;
>> +			num-cs = <1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		spi_1: spi@14d30000 {
>> +			compatible = "samsung,exynos5433-spi";
>> +			reg = <0x14d30000 0x100>;
>> +			interrupts = <0 433 0>;
>> +			dmas = <&pdma0 11>, <&pdma0 10>;
>> +			dma-names = "tx", "rx";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_peric CLK_PCLK_SPI1>,
>> +				<&cmu_peric CLK_SCLK_SPI1>,
>> +				<&cmu_peric CLK_SCLK_IOCLK_SPI1>;
>> +			clock-names = "spi", "spi_busclk0", "spi_ioclk";
>> +			samsung,spi-src-clk = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi1_bus>;
>> +			num-cs = <1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		spi_2: spi@14d40000 {
>> +			compatible = "samsung,exynos5433-spi";
>> +			reg = <0x14d40000 0x100>;
>> +			interrupts = <0 434 0>;
>> +			dmas = <&pdma0 13>, <&pdma0 12>;
>> +			dma-names = "tx", "rx";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_peric CLK_PCLK_SPI2>,
>> +				 <&cmu_peric CLK_SCLK_SPI2>,
>> +				 <&cmu_peric CLK_SCLK_IOCLK_SPI2>;
>> +			clock-names = "spi", "spi_busclk0", "spi_ioclk";
>> +			samsung,spi-src-clk = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi2_bus>;
>> +			num-cs = <1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		spi_3: spi@14d50000 {
>> +			compatible = "samsung,exynos5433-spi";
>> +			reg = <0x14d50000 0x100>;
>> +			interrupts = <0 447 0>;
>> +			dmas = <&pdma0 23>, <&pdma0 22>;
>> +			dma-names = "tx", "rx";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_peric CLK_PCLK_SPI3>,
>> +				<&cmu_peric CLK_SCLK_SPI3>,
>> +				<&cmu_peric CLK_SCLK_IOCLK_SPI3>;
>> +			clock-names = "spi", "spi_busclk0", "spi_ioclk";
>> +			samsung,spi-src-clk = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi3_bus>;
>> +			num-cs = <1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		spi_4: spi@14d00000 {
>> +			compatible = "samsung,exynos5433-spi";
>> +			reg = <0x14d00000 0x100>;
>> +			interrupts = <0 412 0>;
>> +			dmas = <&pdma0 25>, <&pdma0 24>;
>> +			dma-names = "tx", "rx";
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			clocks = <&cmu_peric CLK_PCLK_SPI4>,
>> +				<&cmu_peric CLK_SCLK_SPI4>,
>> +				<&cmu_peric CLK_SCLK_IOCLK_SPI4>;
>> +			clock-names = "spi", "spi_busclk0", "spi_ioclk";
>> +			samsung,spi-src-clk = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&spi4_bus>;
>> +			num-cs = <1>;
>> +			status = "disabled";
>> +		};
>> +
>> +		adc: adc@14d10000 {
>> +			compatible = "samsung,exynos7-adc";
>> +			reg = <0x14d10000 0x100>;
>> +			interrupts = <0 438 0>;
>> +			clock-names = "adc";
>> +			clocks = <&cmu_peric CLK_PCLK_ADCIF>;
>> +			#io-channel-cells = <1>;
>> +			io-channel-ranges;
>> +			status = "disabled";
>> +		};
>> +
>> +		pwm: pwm@14dd0000 {
>> +			compatible = "samsung,exynos4210-pwm";
>> +			reg = <0x14dd0000 0x100>;
>> +			interrupts = <0 416 0>, <0 417 0>,
>> +				<0 418 0>, <0 419 0>, <0 420 0>;
>> +			samsung,pwm-outputs = <0>, <1>, <2>, <3>;
>> +			clocks = <&cmu_peric CLK_PCLK_PWM>;
>> +			clock-names = "timers";
>> +			#pwm-cells = <3>;
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_0: hsi2c@14e40000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14e40000 0x1000>;
>> +			interrupts = <0 428 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c0_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C0>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_1: hsi2c@14e50000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14e50000 0x1000>;
>> +			interrupts = <0 429 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c1_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C1>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_2: hsi2c@14e60000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14e60000 0x1000>;
>> +			interrupts = <0 430 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c2_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C2>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_3: hsi2c@14e70000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14e70000 0x1000>;
>> +			interrupts = <0 431 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c3_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C3>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_4: hsi2c@14ec0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14ec0000 0x1000>;
>> +			interrupts = <0 424 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c4_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C4>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_5: hsi2c@14ed0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14ed0000 0x1000>;
>> +			interrupts = <0 425 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c5_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C5>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_6: hsi2c@14ee0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14ee0000 0x1000>;
>> +			interrupts = <0 426 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c6_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C6>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_7: hsi2c@14ef0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14ef0000 0x1000>;
>> +			interrupts = <0 427 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c7_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C7>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_8: hsi2c@14d90000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14d90000 0x1000>;
>> +			interrupts = <0 443 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c8_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C8>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_9: hsi2c@14da0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14da0000 0x1000>;
>> +			interrupts = <0 444 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c9_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C9>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_10: hsi2c@14de0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14de0000 0x1000>;
>> +			interrupts = <0 445 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c10_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C10>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		hsi2c_11: hsi2c@14df0000 {
>> +			compatible = "samsung,exynos7-hsi2c";
>> +			reg = <0x14df0000 0x1000>;
>> +			interrupts = <0 446 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			pinctrl-names = "default";
>> +			pinctrl-0 = <&hs_i2c11_bus>;
>> +			clocks = <&cmu_peric CLK_PCLK_HSI2C11>;
>> +			clock-names = "hsi2c";
>> +			status = "disabled";
>> +		};
>> +
>> +		usbdrd30: usb@15400000 {
>> +			compatible = "samsung,exynos5250-dwusb3";
>> +			clocks = <&cmu_fsys CLK_ACLK_USBDRD30>,
>> +				<&cmu_fsys CLK_SCLK_USBDRD30>;
>> +			clock-names = "usbdrd30", "usbdrd30_susp_clk";
>> +			assigned-clocks =
>> +				<&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
>> +				<&cmu_top CLK_MOUT_SCLK_USBDRD30>,
>> +				<&cmu_top CLK_DIV_SCLK_USBDRD30>;
>> +			assigned-clock-parents =
>> +				<&cmu_top CLK_SCLK_USBDRD30_FSYS>,
>> +				<&cmu_top CLK_MOUT_BUS_PLL_USER>;
>> +			assigned-clock-rates = <0>, <0>, <66700000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			status = "disabled";
>> +
>> +			dwc3 {
>> +				compatible = "snps,dwc3";
>> +				reg = <0x15400000 0x10000>;
>> +				interrupts = <0 231 0>;
>> +				phys = <&usbdrd30_phy 0>, <&usbdrd30_phy 1>;
>> +				phy-names = "usb2-phy", "usb3-phy";
>> +			};
>> +
>> +		};
>> +
>> +		usbdrd30_phy: phy@15500000 {
>> +			compatible = "samsung,exynos5433-usbdrd-phy";
>> +			reg = <0x15500000 0x100>;
>> +			clocks = <&cmu_fsys CLK_ACLK_USBDRD30>, <&xxti>,
>> +				<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK>,
>> +				<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK>,
>> +				<&cmu_fsys CLK_SCLK_USBDRD30>;
>> +			clock-names = "phy", "ref", "phy_utmi", "phy_pipe", "itp";
>> +			assigned-clocks =
>> +				<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
>> +				<&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>;
>> +			assigned-clock-parents =
>> +				<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
>> +				<&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>;
>> +			#phy-cells = <1>;
>> +			samsung,pmu-syscon = <&pmu_system_controller>;
>> +			status = "disabled";
>> +		};
>> +
>> +		usbhost30_phy: phy@15580000 {
>> +			compatible = "samsung,exynos5433-usbdrd-phy";
>> +			reg = <0x15580000 0x100>;
>> +			clocks = <&cmu_fsys CLK_ACLK_USBHOST30>, <&xxti>,
>> +				<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK>,
>> +				<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK>,
>> +				<&cmu_fsys CLK_SCLK_USBHOST30>;
>> +			clock-names = "phy", "ref", "phy_utmi", "phy_pipe",
>> +					"itp";
>> +			assigned-clocks =
>> +				<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
>> +				<&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>;
>> +			assigned-clock-parents =
>> +				<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
>> +				<&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
>> +			#phy-cells = <1>;
>> +			samsung,pmu-syscon = <&pmu_system_controller>;
>> +			status = "disabled";
>> +		};
>> +
>> +		usbhost30: usb@15a00000 {
>> +			compatible = "samsung,exynos5250-dwusb3";
>> +			clocks = <&cmu_fsys CLK_ACLK_USBHOST30>,
>> +				<&cmu_fsys CLK_SCLK_USBHOST30>;
>> +			clock-names = "usbdrd30", "usbdrd30_susp_clk";
>> +			assigned-clocks =
>> +				<&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
>> +				<&cmu_top CLK_MOUT_SCLK_USBHOST30>,
>> +				<&cmu_top CLK_DIV_SCLK_USBHOST30>;
>> +			assigned-clock-parents =
>> +				<&cmu_top CLK_SCLK_USBHOST30_FSYS>,
>> +				<&cmu_top CLK_MOUT_BUS_PLL_USER>;
>> +			assigned-clock-rates = <0>, <0>, <66700000>;
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +			status = "disabled";
>> +
>> +			usbdrd_dwc3_0: dwc3 {
>> +				compatible = "snps,dwc3";
>> +				reg = <0x15a00000 0x10000>;
>> +				interrupts = <0 244 0>;
>> +				phys = <&usbhost30_phy 0>, <&usbhost30_phy 1>;
>> +				phy-names = "usb2-phy", "usb3-phy";
>> +			};
>> +		};
>> +
>> +		mshc_0: mshc@15540000 {
>> +			compatible = "samsung,exynos7-dw-mshc-smu";
>> +			interrupts = <0 225 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x15540000 0x2000>;
>> +			clocks = <&cmu_fsys CLK_ACLK_MMC0>,
>> +				<&cmu_fsys CLK_SCLK_MMC0>;
>> +			clock-names = "biu", "ciu";
>> +			fifo-depth = <0x40>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mshc_1: mshc@15550000 {
>> +			compatible = "samsung,exynos7-dw-mshc-smu";
>> +			interrupts = <0 226 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x15550000 0x2000>;
>> +			clocks = <&cmu_fsys CLK_ACLK_MMC1>,
>> +				<&cmu_fsys CLK_SCLK_MMC1>;
>> +			clock-names = "biu", "ciu";
>> +			fifo-depth = <0x40>;
>> +			status = "disabled";
>> +		};
>> +
>> +		mshc_2: mshc@15560000 {
>> +			compatible = "samsung,exynos7-dw-mshc-smu";
>> +			interrupts = <0 227 0>;
>> +			#address-cells = <1>;
>> +			#size-cells = <0>;
>> +			reg = <0x15560000 0x2000>;
>> +			clocks = <&cmu_fsys CLK_ACLK_MMC2>,
>> +				<&cmu_fsys CLK_SCLK_MMC2>;
>> +			clock-names = "biu", "ciu";
>> +			fifo-depth = <0x40>;
>> +			status = "disabled";
>> +		};
>> +
>> +		amba {
>> +			compatible = "arm,amba-bus";
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges;
>> +
>> +			pdma0: pdma@15610000 {
>> +				compatible = "arm,pl330", "arm,primecell";
>> +				reg = <0x15610000 0x1000>;
>> +				interrupts = <0 228 0>;
>> +				clocks = <&cmu_fsys CLK_PDMA0>;
>> +				clock-names = "apb_pclk";
>> +				#dma-cells = <1>;
>> +				#dma-channels = <8>;
>> +				#dma-requests = <32>;
>> +			};
>> +
>> +			pdma1: pdma@15600000 {
>> +				compatible = "arm,pl330", "arm,primecell";
>> +				reg = <0x15600000 0x1000>;
>> +				interrupts = <0 246 0>;
>> +				clocks = <&cmu_fsys CLK_PDMA1>;
>> +				clock-names = "apb_pclk";
>> +				#dma-cells = <1>;
>> +				#dma-channels = <8>;
>> +				#dma-requests = <32>;
>> +			};
>> +
>> +			adma: adma@11420000 {
>> +				compatible = "arm,pl330", "arm,primecell";
>> +				reg = <0x11420000 0x1000>;
>> +				interrupts = <0 73 0>;
>> +				clocks = <&cmu_aud CLK_ACLK_DMAC>;
>> +				clock-names = "apb_pclk";
>> +				#dma-cells = <1>;
>> +				#dma-channels = <8>;
>> +				#dma-requests = <32>;
>> +			};
>> +		};
>> +	};
>> +
>> +	timer: timer {
>> +		compatible = "arm,armv8-timer";
>> +		interrupts = <1 13 0xff04>,
>> +			     <1 14 0xff04>,
>> +			     <1 11 0xff04>,
>> +			     <1 10 0xff04>;
> 
> Please use human friendly names from
> dt-bindings/interrupt-controller/arm-gic.h. Something like this:
> https://git.kernel.org/cgit/linux/kernel/git/krzk/linux.git/commit/?h=next/dt64&id=36d1c9cd07cd6a065f1dde3cbbfe3a9867d693a4

Thanks for reference. I'll modify it.

Best Regards,
Chanwoo Choi


--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  Powered by Linux