Hi,
I mentioned overheating problem of Odroid XU3-Lite after enabling
cpufreq-dt (when busy in a quite warm room). [0]
The patchset tries to fix this by adding CPU cooling device.
Unfortunately apparently I screwed something because on next-20160216
it does not help.
The fan works at full but CPU cooler is not enabled.
Patchset adds 2 additional trip points (so total 5). First 3 trip
points enable the fan. The new two trip points should trigger CPU
cooler.
However after reaching last fan trip point, the thermal zone stops
sending updates to the step-wise governor.
The last log for thermal_zone0 is:
[ 1366.604672] thermal thermal_zone0: last_temperature=71000, current_temperature=71000
[ 1366.604699] thermal thermal_zone0: Trip0[type=0,temp=50000]:trend=0,throttle=1
instance->upper:
instance->lower:
throttle:
[ 1366.604713] thermal cooling_device0: cur_state=0, 1, 0, throttle: 1
[ 1366.604725] thermal cooling_device0: CUR_state=0, 1, 0, throttle: 1
[ 1366.604735] thermal cooling_device0: old_target=1, target=1
[ 1366.604754] thermal thermal_zone0: Trip1[type=0,temp=60000]:trend=0,throttle=1
[ 1366.604776] thermal cooling_device0: cur_state=0, 2, 1, throttle: 1
[ 1366.604786] thermal cooling_device0: CUR_state=0, 2, 1, throttle: 1
[ 1366.604796] thermal cooling_device0: old_target=2, target=2
[ 1366.604810] thermal thermal_zone0: Trip2[type=0,temp=70000]:trend=0,throttle=1
[ 1366.604821] thermal cooling_device0: cur_state=0, 3, 2, throttle: 1
[ 1366.604832] thermal cooling_device0: CUR_state=0, 3, 2, throttle: 1
[ 1366.604841] thermal cooling_device0: old_target=3, target=3
[ 1366.604856] thermal thermal_zone0: Trip4[type=1,temp=90000]:trend=0,throttle=0
[ 1366.604869] thermal cooling_device1: cur_state=0, 3, 0, throttle: 0
[ 1366.604879] thermal cooling_device1: CUR_state=0, 3, 0, throttle: 0
[ 1366.604889] thermal cooling_device1: old_target=-1, target=-1
[ 1366.604901] thermal cooling_device2: cur_state=0, 3, 0, throttle: 0
[ 1366.604911] thermal cooling_device2: CUR_state=0, 3, 0, throttle: 0
[ 1366.604921] thermal cooling_device2: old_target=-1, target=-1
[ 1366.604935] thermal thermal_zone0: Trip5[type=1,temp=110000]:trend=0,throttle=0
[ 1366.604946] thermal cooling_device1: cur_state=0, 7, 7, throttle: 0
[ 1366.604957] thermal cooling_device1: CUR_state=0, 7, 7, throttle: 0
[ 1366.604967] thermal cooling_device1: old_target=-1, target=-1
[ 1366.604977] thermal cooling_device2: cur_state=0, 11, 11, throttle: 0
[ 1366.604988] thermal cooling_device2: CUR_state=0, 11, 11, throttle: 0
[ 1366.604997] thermal cooling_device2: old_target=-1, target=-1
After this, the temperature in zone0 rises but cooling devices do not
receive any pokes...
Did I make some mistake or this is thermal issue?
[0] http://www.spinics.net/lists/arm-kernel/msg482748.html
Best regards,
Krzysztof
Krzysztof Kozlowski (3):
ARM: dts: Add cooling levels for CPUs on exynos5420
ARM: dts: Add cooling levels for CPUs on exynos5422/5800
ARM: dts: Don't overheat the Odroid XU3-Lite on high load
arch/arm/boot/dts/exynos5420-cpus.dtsi | 6 ++++
arch/arm/boot/dts/exynos5422-cpu-thermal.dtsi | 41 +++++++++++++++++++++++++++
arch/arm/boot/dts/exynos5422-cpus.dtsi | 6 ++++
3 files changed, 53 insertions(+)
--
2.5.0
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
