hi Krzysztof,
On 22 October 2015 at 18:34, Anand Moon <linux.amoon@xxxxxxxxx> wrote:
> hi Krzysztof,
>
> On 22 October 2015 at 06:31, Krzysztof Kozlowski
> <k.kozlowski@xxxxxxxxxxx> wrote:
>> On 20.10.2015 21:56, Anand Moon wrote:
>>> Changes need for host controller to detect UHS-I highspeed cards.
>>> Changes in VDDQ_MMC2 voltage range help scale
>>> the required voltage to detect and load the microSD cards.
>>
>> Thanks for updating description of commit.
>>
>>>
>>> Signed-off-by: Anand Moon <linux.amoon@xxxxxxxxx>
>>> ---
>>> Changes based on git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung.git v4.4-next/dt-samsung branch
>>>
>>> Changes:
>>> Drop the ranp_delay for LDO9.
>>>
>>> Thanks to : Krzysztof, Doug Anderson, Jaehoon Chung for helping
>>> me out figure out the mmc core requirement.
>>>
>>> Also drop the previous changes:
>>> use cd-gpio method to detect sd-card.
>>> Added UHS-I bus speed support.
>>>
>>> [ 4.713553] random: nonblocking pool is initialized
>>> [ 4.718423] 14530000.hdmi supply hdmi-en not found, using dummy regulator
>>> [ 4.726206] exynos-drm exynos-drm: bound 14400000.fimd (ops fimd_component_ops)
>>> [ 4.732555] exynos-drm exynos-drm: bound 14450000.mixer (ops mixer_component_ops)
>>> [ 4.740180] exynos-drm exynos-drm: bound 14530000.hdmi (ops hdmi_component_ops)
>>> [ 4.746936] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
>>> [ 4.753428] [drm] No driver support for vblank timestamp query.
>>> [ 4.940794] Console: switching to colour frame buffer device 274x77
>>> [ 4.995344] exynos-drm exynos-drm: fb0: frame buffer device
>>> [ 5.024573] [drm] Initialized exynos 1.0.0 20110530 on minor 0
>>> [ 5.031164] exynos-dwc3 usb@12000000: no suspend clk specified
>>> [ 5.054571] usb 2-1: new full-speed USB device number 2 using exynos-ohci
>>> [ 5.159527] dwmmc_exynos 12220000.mmc: Busy; trying anyway
>>> [ 5.163705] mmc_host mmc1: Timeout sending command (cmd 0x202000 arg 0x0 status 0x0)
>>> ---
>>> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 7 ++++++-
>>> 1 file changed, 6 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> index 1af5bdc..a4be3e0 100644
>>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
>>> @@ -182,9 +182,10 @@
>>>
>>> ldo13_reg: LDO13 {
>>> regulator-name = "vdd_ldo13";
>>> - regulator-min-microvolt = <2800000>;
>>> + regulator-min-microvolt = <1800000>;
>>
>> You did not convinced me in previous discussion about the change to
>> 1.8V. I said that:
>>> On the same diagram few lines below:
>>> VDDQ_MMC2: 2.8V 250mA
>>
>> You responded:
>>> You are correct.
>>
>> So I am confused. Are you sure that this SD card block can/should
>> operate on 1.8V? Have you actually tried this?
>>
>
> Look like I missed this point. Here is the link I would like to share.
>
> http://www.hjreggel.net/cardspeed/cs_sdxc.html
> Section: Summary of SD modes
>
> https://en.wikipedia.org/wiki/Secure_Digital
> Section: Power consumption
>
> Their different requirement for voltage requirement for UHS-I, the max
> value is around 3.3V
Do you have any comment on this voltage selection for UHS-I card (1.8V).
>
>>> regulator-max-microvolt = <2800000>;
>>> regulator-always-on;
>>> + regulator-ramp-delay = <12000>;
>>
>> NAK
>>
>> We've been talking about this. Sooo maaaanyyyy times.
>>
>> If you are going to send v3 please come up with detailed reasoning,
>> which will convince my stubborn mind.
>>
>
> Look like I missed this point. my typo. Will drop this in next version.
> No matter I try hard, it turn out I make silly and annoying mistake.
>
> -Anand Moon
>
Well I will drop this.
>> Best regards,
>> Krzysztof
>>
>>> };
>>>
>>> ldo15_reg: LDO15 {
>>> @@ -213,6 +214,7 @@
>>> regulator-min-microvolt = <2800000>;
>>> regulator-max-microvolt = <2800000>;
>>> regulator-always-on;
>>> + regulator-ramp-delay = <12000>;
>>> };
>>>
>>> ldo24_reg: LDO24 {
>>> @@ -338,6 +340,7 @@
>>> samsung,dw-mshc-ddr-timing = <0 2>;
>>> samsung,dw-mshc-hs400-timing = <0 2>;
>>> samsung,read-strobe-delay = <90>;
>>> + vmmc-supply = <&ldo3_reg>;
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_cd &sd0_rclk>;
>>> bus-width = <8>;
>>> @@ -355,6 +358,8 @@
>>> pinctrl-names = "default";
>>> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus1 &sd2_bus4>;
>>> bus-width = <4>;
>>> + vmmc-supply = <&ldo19_reg>;
>>> + vqmmc-supply = <&ldo13_reg>;
>>> cap-sd-highspeed;
>>> };
>>>
>>>
>>
I will take care on not repeating my mistake again.
-Anand Moon
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
