On 03.11.2015 18:16, Pavel Fedin wrote:
> The chip is smsc9115, connected via SROMc bank 3. Additionally, some GPIO
> initialization is required.
>
> Signed-off-by: Pavel Fedin <p.fedin@xxxxxxxxxxx>
> ---
> arch/arm/boot/dts/exynos5410-smdk5410.dts | 40 +++++++++++++++++++++++++++++++
> 1 file changed, 40 insertions(+)
>
> diff --git a/arch/arm/boot/dts/exynos5410-smdk5410.dts b/arch/arm/boot/dts/exynos5410-smdk5410.dts
> index cebeaab..f41952f 100644
> --- a/arch/arm/boot/dts/exynos5410-smdk5410.dts
> +++ b/arch/arm/boot/dts/exynos5410-smdk5410.dts
> @@ -61,6 +61,27 @@
> disable-wp;
> };
>
> +&pinctrl_0 {
> + srom_ctl: srom-ctl {
> + samsung,pins = "gpy0-3", "gpy0-4", "gpy0-5",
> + "gpy1-0", "gpy1-1", "gpy1-2", "gpy1-3";
> + samsung,pin-function = <2>;
> + samsung,pin-drv = <0>;
> + };
> +
> + srom_ebi: srom-ebi {
> + samsung,pins = "gpy3-0", "gpy3-1", "gpy3-2", "gpy3-3",
> + "gpy3-4", "gpy3-5", "gpy3-6", "gpy3-7",
> + "gpy5-0", "gpy5-1", "gpy5-2", "gpy5-3",
> + "gpy5-4", "gpy5-5", "gpy5-6", "gpy5-7",
> + "gpy6-0", "gpy6-1", "gpy6-2", "gpy6-3",
> + "gpy6-4", "gpy6-5", "gpy6-6", "gpy6-7";
> + samsung,pin-function = <2>;
> + samsung,pin-pud = <3>;
> + samsung,pin-drv = <0>;
> + };
> +};
> +
> &uart0 {
> status = "okay";
> };
> @@ -72,3 +93,22 @@
> &uart2 {
> status = "okay";
> };
> +
> +&sromc {
Put sromc in alphabetical order.
> + pinctrl-names = "default";
> + pinctrl-0 = <&srom_ctl>, <&srom_ebi>;
> +
> + ethernet@3 {
> + compatible = "smsc,lan9115";
> + reg = <3 0 0x10000>;
> + phy-mode = "mii";
> + interrupt-parent = <&gpx0>;
> + interrupts = <5 8>;
s/8/IRQ_TYPE_LEVEL_LOW/
(is this really level low interrupt?)
> + reg-io-width = <2>;
> + smsc,irq-push-pull;
> + smsc,force-internal-phy;
> +
> + samsung,srom-page-mode = <1>;
> + samsung,srom-timing = <9 12 1 9 1 1>;
Some other DTS include regulators: vddvario-supply and vdd33a-supply. It
seems that they are not described in SMSC911x bindings but in
GPMC-eth... but the smsc911x driver is requesting them. Could you
investigate that? I think these regulators should be provided (and
SMSC911x bindings should be updated).
> + };
> +};
I don't have the board schematics so I couldn't verify the GPIOs.
Overall looks good.
Best regards,
Krzysztof
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
