Re: [PATCH 1/1] ARM: dts: Add HS400 support for exynos5422-odroidxu3

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

the base patch in [0] has been applied now.

My patch was meanwhile

Tested-by: Anand Moon <linux.amoon@xxxxxxxxx>


Am 31.03.2015 um 14:27 schrieb Markus Reichl:
> Am 30.03.2015 um 17:51 schrieb Markus Reichl:
>> HS400 timing values are added for exynos5422-odroidxu3 board.
>> ---
>> This patch is analog to [0].
>> This patch needs [0] for the pin-ctrl definition of sd0_rclk.
>>
>> [0]: https://www.mail-archive.com/linux-samsung-soc%40vger.kernel.org/msg42902.html
>>
>> Signed-off-by: Markus Reichl <m.reichl@xxxxxxxxxxxxx>
>> ---
>>  arch/arm/boot/dts/exynos5422-odroidxu3.dts | 7 ++++++-
>>  1 file changed, 6 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
>> index a519c86..0408ec0 100644
>> --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
>> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
>> @@ -298,15 +298,20 @@
>>  
>>  &mmc_0 {
>>  	status = "okay";
>> +	num-slots = <1>;
>>  	broken-cd;
>>  	card-detect-delay = <200>;
>>  	samsung,dw-mshc-ciu-div = <3>;
>>  	samsung,dw-mshc-sdr-timing = <0 4>;
>>  	samsung,dw-mshc-ddr-timing = <0 2>;
>> +	samsung,dw-mshc-hs400-timing = <0 2>;
>> +	samsung,read-strobe-delay = <90>;
>>  	pinctrl-names = "default";
>> -	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
>> +	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8 &sd0_rclk>;
>>  	bus-width = <8>;
>>  	cap-mmc-highspeed;
>> +	mmc-hs200-1_8v;
>> +	mmc-hs400-1_8v;
>>  };
>>  
>>  &mmc_2 {
>>
> 
> hdparm -t /dev/mmcblk0
> 
> without this patch:
> /dev/mmcblk0:
>  Timing buffered disk reads: 230 MB in  3.01 seconds =  76.30 MB/sec
> 
> with this patch:
> /dev/mmcblk0:
>  Timing buffered disk reads: 588 MB in  3.00 seconds = 195.92 MB/sec
> 
> cat /sys/kernel/debug/mmc0/ios
> 
> without patch:
> clock:          52000000 Hz
> vdd:            7 (1.65 - 1.95 V)
> bus mode:       2 (push-pull)
> chip select:    0 (don't care)
> power mode:     2 (on)
> bus width:      3 (8 bits)
> timing spec:    8 (mmc DDR52)
> signal voltage: 0 (1.80 V)
> 
> with patch:
> clock:          200000000 Hz
> vdd:            7 (1.65 - 1.95 V)
> bus mode:       2 (push-pull)
> chip select:    0 (don't care)
> power mode:     2 (on)
> bus width:      3 (8 bits)
> timing spec:    10 (mmc HS400)
> signal voltage: 0 (1.80 V)
> 
> Best Regards
> 


-- 
Markus Reichl

Attachment: signature.asc
Description: OpenPGP digital signature


[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  Powered by Linux