On pon, 2014-12-01 at 23:34 +0900, Tomasz Figa wrote: > 2014-12-01 17:37 GMT+09:00 Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>: > > > > On nie, 2014-11-30 at 21:19 +0900, Tomasz Figa wrote: > >> Hi Krzysztof, > >> (...) > > > >> Also isn't a similar problem happening due to power domains? I believe > >> the whole maudio block is located in a separate power domain but > >> somehow it doesn't get turned off? > > > > There is Maudio power domain... but I think it is not related here. > > Could you somehow check what happens when the maudio power domain is > turned off and maudio pin controller is accessed? Could you also check > the difference in power consumption with this domain powered on and > off? Hi Tomasz, Some time ago you asked for some details of Exynos5420 Maudio domain behavior. Here it goes: 1. mau domain ON, EPL: OFF: boot hang (this was behavior after adding runtime PM to pl330 driver) 2. maud domain OFF, EPLL OFF: boot hang 3. maud domain ON, EPLL ON: works (current linux-next and mainline) 4. maud domain OFF, EPLL ON: works, almost the same energy consumption as in (3) (diff: 0.1% so it is smaller than measuring accuracy). However an unspecified imprecise abort shows up in (4): [ 11.911628] Freeing unused kernel memory: 328K (c0674000 - c06c6000) [ 12.122695] usb 5-1.4: new high-speed USB device number 3 using exynos-ehci [ 12.190011] Unhandled fault: imprecise external abort (0x1406) at 0x00000000 [ 12.219062] usb 5-1.4: New USB device found, idVendor=0b95, idProduct=772a [ 12.224548] usb 5-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 12.231794] usb 5-1.4: Product: AX88772 [ 12.235681] usb 5-1.4: Manufacturer: ASIX Elec. Corp. [ 12.240707] usb 5-1.4: SerialNumber: 000001 [ 12.248835] asix 5-1.4:1.0 (unnamed net_device) (uninitialized): invalid hw address, using random root@(none):/# Best regards, Krzysztof > > > Pinctrl driver does not have runtime PM and is not attached to a domain. > > I thought about other solution to this problem (with utilization of > > power domains): > > - add runtime PM to pinctrl and audss clocks, > > - attach pinctrl and audss clocks to maudio power domain, > > - enable the clock when power domain is turned on. > > However almost the same changes had to be added to pinctrl and audss > > clocks drivers (replace clock_enable() with pm_runtime_get_sync()). > > Well, if the dependency is there due to hardware design, I think it > needs to be reflected in the drivers as well. > > Few other issues that came to my mind: > > - Your previous patch added clock control only to pinctrl operations. > Shouldn't GPIO operations be included as well? > > - If power domain dependency is there too, what happens with GPIO > pins if the domain is powered off? If they lose their states, wouldn't > it necessary to keep the domain powered on whenever there is some GPIO > pin requested (which usually = in use)? (I'd assume that special > functions shouldn't take a reference on runtime PM, because they are > related to IP blocks in the same PM domain, which will implicitly keep > the domain powered on.) > > - Doesn't the clock controller also lose its state whenever the power > domain is powered off? I guess that would be similar to ISP clock > controller, issues of which are still not resolved in mainline. > Sylwester could tell you more about this, I guess. > > Best regards, > Tomasz -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |