On 12/23/2014 04:48 AM, Marek Szyprowski wrote:
> -static void l2c310_resume(void)
> +static void l2c310_configure(void __iomem *base)
> {
> - void __iomem *base = l2x0_base;
> + unsigned revision;
>
> - if (!(readl_relaxed(base + L2X0_CTRL) & L2X0_CTRL_EN)) {
> - unsigned revision;
> -
> - /* restore pl310 setup */
> - writel_relaxed(l2x0_saved_regs.tag_latency,
> - base + L310_TAG_LATENCY_CTRL);
> - writel_relaxed(l2x0_saved_regs.data_latency,
> - base + L310_DATA_LATENCY_CTRL);
> - writel_relaxed(l2x0_saved_regs.filter_end,
> - base + L310_ADDR_FILTER_END);
> - writel_relaxed(l2x0_saved_regs.filter_start,
> - base + L310_ADDR_FILTER_START);
> -
> - revision = readl_relaxed(base + L2X0_CACHE_ID) &
> - L2X0_CACHE_ID_RTL_MASK;
> -
> - if (revision >= L310_CACHE_ID_RTL_R2P0)
> - l2c_write_sec(l2x0_saved_regs.prefetch_ctrl, base,
> - L310_PREFETCH_CTRL);
> - if (revision >= L310_CACHE_ID_RTL_R3P0)
> - l2c_write_sec(l2x0_saved_regs.pwr_ctrl, base,
> - L310_POWER_CTRL);
> -
> - l2c_enable(base, l2x0_saved_regs.aux_ctrl, 8);
> -
> - /* Re-enable full-line-of-zeros for Cortex-A9 */
> - if (l2x0_saved_regs.aux_ctrl & L310_AUX_CTRL_FULL_LINE_ZERO)
> - set_auxcr(get_auxcr() | BIT(3) | BIT(2) | BIT(1));
> - }
> + /* restore pl310 setup */
> + writel_relaxed(l2x0_saved_regs.tag_latency,
> + base + L310_TAG_LATENCY_CTRL);
> + writel_relaxed(l2x0_saved_regs.data_latency,
> + base + L310_DATA_LATENCY_CTRL);
> + writel_relaxed(l2x0_saved_regs.filter_end,
> + base + L310_ADDR_FILTER_END);
> + writel_relaxed(l2x0_saved_regs.filter_start,
> + base + L310_ADDR_FILTER_START);
> +
^^ The above change broke AM437xx. Looks like the change causes the
following behavior difference on AM437x. For some reason, touching any
of the above 4 registers(even with the values read from the same
registers) causes AM437x to go beserk. Comment the 4 writes and we
reach shell. looks like l2c310_resume is not invoked prior to this
series. :(.. now that we reuse that logic to actually do programming,
we start to see the problem.
one option might be to write only those registers that differ from
saved_registers (example: unmodified values dont need reprogramming).
Looks like the following also need addressing:
data->save is called twice (once more after l2cof_init)
l2c310_init_fns also needs l2c310_configure
will be nice to use l2x0_data only after we kmemdup data in __l2c_init
if you'd like to split this up in pieces, [1] might be nice - will go
good to change the pl310, aurora etc in each chunks to enable better
review.
[1]
https://github.com/nmenon/linux-2.6-playground/commits/temp/l2c-patch2-splitup
--
Regards,
Nishanth Menon
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
