Hi Krzysztof, On 12/10/2014 10:21 PM, Chanwoo Choi wrote: > Hi Krzysztof, > > On Wed, Dec 10, 2014 at 7:07 PM, Krzysztof Kozlowski > <k.kozlowski@xxxxxxxxxxx> wrote: >> On wto, 2014-12-09 at 23:12 +0900, Chanwoo Choi wrote: >>> This patchset add new devfreq_event class to provide raw data to determine >>> current utilization of device which is used for devfreq governor. >>> >>> [Description of devfreq-event class] >>> This patchset add new devfreq_event class for devfreq_event device which provide >>> raw data (e.g., memory bus utilization/GPU utilization). This raw data from >>> devfreq_event data would be used for the governor of devfreq subsystem. >>> - devfreq_event device : Provide raw data for governor of existing devfreq device >>> - devfreq device : Monitor device state and change frequency/voltage of device >>> using the raw data from devfreq_event device >>> >>> The devfreq subsystem support generic DVFS(Dynamic Voltage/Frequency Scaling) >>> for Non-CPU Devices. The devfreq device would dertermine current device state >>> using various governor (e.g., ondemand, performance, powersave). After completed >>> determination of system state, devfreq device would change the frequency/voltage >>> of devfreq device according to the result of governor. >>> >>> But, devfreq governor must need basic data which indicates current device state. >>> Existing devfreq subsystem only consider devfreq device which check current system >>> state and determine proper system state using basic data. There is no subsystem >>> for device providing basic data to devfreq device. >>> >>> The devfreq subsystem must need devfreq_event device(data-provider device) for >>> existing devfreq device. So, this patch add new devfreq_event class for >>> devfreq_event device which read various basic data(e.g, memory bus utilization, >>> GPU utilization) and provide measured data to existing devfreq device through >>> standard APIs of devfreq_event class. >>> >>> The following description explains the feature of two kind of devfreq class: >>> - devfreq class (existing) >>> : devfreq consumer device use raw data from devfreq_event device for >>> determining proper current system state and change voltage/frequency >>> dynamically using various governors. >>> - devfreq_event class (new) >>> : Provide measured raw data to devfreq device for governor >>> >>> Also, the devfreq-event device would support various type event as following: >>> : DEVFREQ_EVENT_TYPE_RAW_DATA >>> : DEVFREQ_EVENT_TYPE_UTILIZATION >>> : DEVFREQ_EVENT_TYPE_BANDWIDTH >>> : DEVFREQ_EVENT_TYPE_LATENCY >>> >>> [For example] >>> If board dts includes PPMU_DMC0/DMC1/CPU event node, >>> would show following sysfs entry. Also devfreq driver(e.g., exynos4_bus.c) >>> can get the instance of devfreq-event device by using provided API and then >>> get raw data which reflect the current state of device. >>> >> >> Hi, >> >> Overall I like the idea. I understand that now devfreq devices (like >> exynos devfreq) should bind themselves to buses, not to PPMU. It makes >> sense to me because bus clock and bus voltage are properties of bus, not >> monitoring unit. >> >> I see that this is still a RFC so it would be hard to base current >> devfreq work on top of it. > > The goal of this patch set is not for devfreq device. This patch set > just is used for > devfreq-event device according to patch description. > > The devfreq must need devfreq-event device (e.g., exynos-ppmu.c) > but current devfreq subsystem have not been supported any reason for > exyons-ppmu.c as devfreq-event device. > > I discussed this same issue on following patch[1] which was posted to support > exynos4 busfreq by me. > [1] https://lkml.org/lkml/2014/3/14/132 > - [PATCHv2 8/8] devfreq: exynos4: Add busfreq driver for exynos4210/exynos4x12 > After discussion, I thought that devfreq-event class must be needed > before supporting > the dt of devfreq device. > > So, I think that devfreq have to support the devfreq-event subsystem > for exynos-ppmu. And then I'll work to support the device-tree of devfreq device > as next job. > >> >> One more general comment: you're adding a some API which is not used by >> current devfreq_event user (exynos). For example the exclusive flag or >> event types. I think it will be simpler to stick to the basic approach >> (reduced API). If some other user emerges then new API will be added. > > I think that devfreq-event must support both event_flag(e.g., exclusive flag) > and event_type(e.g., raw_data, utilization, bandwidth, latency) because > devfreq-event device (e.g., exynos-ppmu) would provide various event data. > For example, exynos-ppmu driver could support the utilization/bandwidth/latency > of each IP of Exynos SoC. I checked PPMU IP on Exynos TRM. > > Also, If specific devfreq-event device should be used on only one device driver, > devfrewq-event class have to support 'exclusive' flag. If > devfreq-event class don't > support the exclusive flag, devfreq-event could not guarantee the > integrity of event > from devfreq-event device. I'll drop 'exclusive' flag according to your comment. Thanks for your review. Best Regards, Chanwoo Choi -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |