Re: [PATCH V6 3/8] drm/panel: simple: Add support for auo_b133htn01 panel

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Jul 30, 2014 at 05:02:11PM +0530, Ajay kumar wrote:
> On Wed, Jul 30, 2014 at 4:21 PM, Thierry Reding
> <thierry.reding@xxxxxxxxx> wrote:
> > On Sat, Jul 26, 2014 at 12:52:05AM +0530, Ajay Kumar wrote:
> >> Add panel_desc structure for auo_b133htn01 eDP panel.
> >>
> >> Also, modify the panel_simple routines to support timing_parameter
> >> delays if mentioned in the panel_desc structure.
> >>
> >> Signed-off-by: Ajay Kumar <ajaykumar.rs@xxxxxxxxxxx>
> >> ---
> >>  .../devicetree/bindings/panel/auo,b133htn01.txt    |    7 +++
> >>  drivers/gpu/drm/panel/panel-simple.c               |   47 ++++++++++++++++++++
> >>  2 files changed, 54 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/panel/auo,b133htn01.txt
> >
> > I think this should be two patches, one which adds the delay parameters
> > and another which adds support for the new panel.
> Ok. Will split it.

I was going to propose that I split this up myself so you no longer have
to worry about it. I can easily apply the changes we discussed. But if
you prefer to keep it in one series that works for me too.

> > In general I think it would be good to have a description of these in
> > the struct panel_desc structure, something like this perhaps:
> >
> >         /**
> >          * @prepare: the time (in milliseconds) that it takes for the panel
> >          *           to become ready and start receiving video data
> >          * @enable: the time (in milliseconds) that it takes for the panel
> >          *          to display the first valid frame after starting to
> >          *          receive video data
> >          * @disable: the time (in milliseconds) that it takes for the panel
> >          *           to turn the display off (no content is visible)
> >          * @unprepare: the time (in milliseconds) that it takes for the panel
>                         to power down itself completely.
> >          */
> >         struct {
> >                 unsigned int prepare;
> >                 unsigned int enable;
> >                 unsigned int disable;
> >                 unsigned int unprepare;
> >         } delay;
> >
> > For prepare and enable delays this would mean that they should take
> > effect at the very end of the .prepare() and .enable() functions,
> > respectively. For disable in means that it should be at the end (for
> > example to take into account the time it takes for backlight to
> > completely turn off). For unprepare I have no idea what we would need it
> > for. And the new panel that you're adding in this patch doesn't use it
> > either, so perhaps it can just be left out (for now)?
> Actually, there was a typo.
> That should have been .unprepare_stage_delay = 50.
> This is needed because panels need some delay before powering
> them on again.
> As in, assume you are doing a test to turn on/off display continuously,
> Then, the delay between
> (N - 1)th cycle poweroff to Nth cycle poweron should be at least 500ms.
> That's what the datasheet says! And, somehow 50ms works fine for me.

Okay, that makes sense then.

Thierry

Attachment: pgpNLSICeT_Lu.pgp
Description: PGP signature


[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  Powered by Linux