Hello Linus,
On 07/10/2014 11:46 AM, Linus Walleij wrote:
> On Fri, Jul 4, 2014 at 10:24 PM, Javier Martinez Canillas
> <javier.martinez@xxxxxxxxxxxxxxx> wrote:
>
>> Some regulators on the MAX77686 PMIC have Dynamic Voltage Scaling
>> (DVS) support that allows output voltage to change dynamically.
>>
>> For MAX77686, these regulators are Buck regulators 2, 3 and 4.
>>
>> Each Buck output voltage is selected using a set of external
>> inputs: DVS1-3 and SELB2-4.
>>
>> DVS registers can be used to configure the output voltages for each
>> Buck regulator and which one is active is controled by DVSx lines.
>>
>> SELBx lines are used to control if individual Buck lines are ON or OFF.
>>
>> This patch adds support to configure the DVSx and SELBx lines
>> from DT and to setup and read the GPIO lines connected to them.
>>
>> Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
>> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>
> (...)
>> +#include <linux/gpio/consumer.h>
>
> THANKS for using modern interfaces!
>
Thanks to you and Alexandre for keep improving the GPIO subsystem!
>> +static void max77686_dt_parse_dvs_gpio(struct device *dev)
>> +{
>> + struct max77686_platform_data *pd = dev_get_platdata(dev);
>> + int i;
>> +
>> + /*
>> + * NOTE: we don't consider GPIO errors fatal; board may have some lines
>> + * directly pulled high or low and thus doesn't specify them.
>> + */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++)
>> + pd->buck_gpio_dvs[i] =
>> + devm_gpiod_get_index(dev, "max77686,pmic-buck-dvs", i);
>> +
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++)
>> + pd->buck_gpio_selb[i] =
>> + devm_gpiod_get_index(dev, "max77686,pmic-buck-selb", i);
>> +}
>
> Rob Jones has a patch cooking that adds gpio_get_array() so this thing
> merits also adding devm_gpiod_get_array() I think?
>
Yes, I just asked [0] Rob on the other thread if he is already implementing the
descriptor-based version of his devm_request_gpio_array() or if I should go and
implement it.
Now, I wonder if that can be done in a follow-up patch (e.g: use the new
devm_gpiod_get_array once it lands in Torvalds tree) since this series already
touches several subsystems (mfd, regulators, clk and rtc) so if possible I would
prefer to not add another cross-subsystem dependency :)
>> +/**
>> + * max77686_setup_gpios() - init DVS-related GPIOs
>> + * @dev: device whose platform data contains the dvs GPIOs information
>> + *
>> + * This function claims / initalizations GPIOs related to DVS if they are
>> + * defined. This may have the effect of switching voltages if the
>> + * pdata->buck_default_idx does not match the boot time state of pins.
>> + */
>> +int max77686_setup_gpios(struct device *dev)
>> +{
>> + struct max77686_platform_data *pd = dev_get_platdata(dev);
>> + int buck_default_idx = pd->buck_default_idx;
>> + int ret;
>> + int i;
>> +
>> + /* Set all SELB high to avoid glitching while DVS is changing */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++) {
>> + struct gpio_desc *gpio = pd->buck_gpio_selb[i];
>> +
>> + /* OK if some GPIOs aren't defined */
>> + if (IS_ERR(gpio))
>> + continue;
>> +
>> + ret = gpiod_direction_output_raw(gpio, 1);
>
> Why does this have to be raw? Usually that is not to be used.
>
Right, I can't think of a good reason why this has to be raw and not just use
gpiod_direction_output() which will check the active-low flag and set the value
accordingly. I'll change it on the next revision.
> Apart from this it looks OK.
>
Great, thanks a lot for your feedback.
> Yours,
> Linus Walleij
>
Best regards,
Javier
[0]: https://lkml.org/lkml/2014/7/10/722
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
