Hello Lee,
Thanks a lot for your feedback.
On 07/09/2014 05:13 PM, Lee Jones wrote:
> I'd really like Linus Walleij to look over this if possible.
>
Ok, I'll cc Linus when posting the next version of the series.
> On Fri, 04 Jul 2014, Javier Martinez Canillas wrote:
>> Some regulators on the MAX77686 PMIC have Dynamic Voltage Scaling
>> (DVS) support that allows output voltage to change dynamically.
>>
>> For MAX77686, these regulators are Buck regulators 2, 3 and 4.
>>
>> Each Buck output voltage is selected using a set of external
>> inputs: DVS1-3 and SELB2-4.
>>
>> DVS registers can be used to configure the output voltages for each
>> Buck regulator and which one is active is controled by DVSx lines.
>>
>> SELBx lines are used to control if individual Buck lines are ON or OFF.
>>
>> This patch adds support to configure the DVSx and SELBx lines
>> from DT and to setup and read the GPIO lines connected to them.
>>
>> Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
>> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@xxxxxxxxxxx>
>> ---
>>
>> Changes since v6:
>> - Add a comment that max77686_read_gpios() function can sleep.
>> Sugggested by Krzysztof Kozlowski
>> ---
>> drivers/mfd/max77686.c | 119 +++++++++++++++++++++++++++++++++++++++++++
>> include/linux/mfd/max77686.h | 18 ++++---
>> 2 files changed, 129 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/mfd/max77686.c b/drivers/mfd/max77686.c
>> index 8650832..d193873 100644
>> --- a/drivers/mfd/max77686.c
>> +++ b/drivers/mfd/max77686.c
>> @@ -32,8 +32,10 @@
>> #include <linux/mfd/core.h>
>> #include <linux/mfd/max77686.h>
>> #include <linux/mfd/max77686-private.h>
>> +#include <linux/gpio/consumer.h>
>> #include <linux/err.h>
>> #include <linux/of.h>
>> +#include <linux/export.h>
>>
>> #define I2C_ADDR_RTC (0x0C >> 1)
>>
>> @@ -101,9 +103,119 @@ static const struct of_device_id max77686_pmic_dt_match[] = {
>> {},
>> };
>>
>> +static void max77686_dt_parse_dvs_gpio(struct device *dev)
>> +{
>> + struct max77686_platform_data *pd = dev_get_platdata(dev);
>> + int i;
>> +
>> + /*
>> + * NOTE: we don't consider GPIO errors fatal; board may have some lines
>> + * directly pulled high or low and thus doesn't specify them.
>> + */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++)
>> + pd->buck_gpio_dvs[i] =
>> + devm_gpiod_get_index(dev, "max77686,pmic-buck-dvs", i);
>> +
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++)
>> + pd->buck_gpio_selb[i] =
>> + devm_gpiod_get_index(dev, "max77686,pmic-buck-selb", i);
>> +}
>
> Not sure why you've pulled this out for parse_dt_pdata()?
>
Ok, I'll remove that function and put the code in max77686_i2c_parse_dt_pdata().
>> +/**
>> + * max77686_setup_gpios() - init DVS-related GPIOs
>> + * @dev: device whose platform data contains the dvs GPIOs information
>> + *
>> + * This function claims / initalizations GPIOs related to DVS if they are
>
> s/initialzations/initialises
>
Right, will fix the typo.
>> + * defined. This may have the effect of switching voltages if the
>
> s/if the/if
>
Ditto.
>> + * pdata->buck_default_idx does not match the boot time state of pins.
>> + */
>> +int max77686_setup_gpios(struct device *dev)
>> +{
>> + struct max77686_platform_data *pd = dev_get_platdata(dev);
>> + int buck_default_idx = pd->buck_default_idx;
>
> You're saving 4 characters once here. Just use the variable in pd.
>
Ok
>> + int ret;
>> + int i;
>
> Don't you want some locking around this?
>
This function is only called in the max77686 and max77802 regulator drivers
probe functions and we expect to have either one of those in a system but never
both so this function can't really be executed concurrently.
And even in the case that a system has both max77686 and max77802 PMICs, all the
data accessed is local to the driver's struct device so I think there is no need
to add any locking here.
>> + /* Set all SELB high to avoid glitching while DVS is changing */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++) {
>> + struct gpio_desc *gpio = pd->buck_gpio_selb[i];
>> +
>> + /* OK if some GPIOs aren't defined */
>> + if (IS_ERR(gpio))
>> + continue;
>> +
>> + ret = gpiod_direction_output_raw(gpio, 1);
>> + if (ret) {
>> + dev_err(dev, "can't set gpio[%d] dir: %d\n", i, ret);
>> + return ret;
>> + }
>> + }
>> +
>> + /* Set our initial setting */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_dvs); i++) {
>> + struct gpio_desc *gpio = pd->buck_gpio_dvs[i];
>> +
>> + /* OK if some GPIOs aren't defined */
>> + if (IS_ERR(gpio))
>> + continue;
>> +
>> + /* If a GPIO is valid, set it */
>> + gpiod_direction_output(gpio, (buck_default_idx >> i) & 1);
>> + if (ret) {
>> + dev_err(dev, "can't set gpio[%d]: dir %d\n", i, ret);
>> + return ret;
>> + }
>> + }
>> +
>> + /* Now set SELB low to take effect */
>> + for (i = 0; i < ARRAY_SIZE(pd->buck_gpio_selb); i++) {
>> + struct gpio_desc *gpio = pd->buck_gpio_selb[i];
>> +
>> + if (!IS_ERR(gpio))
>> + gpiod_set_value(gpio, 0);
>> + }
>> +
>> + return 0;
>> +}
>> +EXPORT_SYMBOL_GPL(max77686_setup_gpios);
>> +
>> +/**
>> + * max77686_read_gpios() - read the current state of the dvs GPIOs
>> + * @pdata: platform data that contains the dvs GPIOs information
>> + *
>> + * We call this function at bootup to detect what slot the firmware was
>> + * using for the DVS GPIOs. That way we can properly preserve the firmware's
>> + * voltage settings
>> + *
>> + * This function can sleep so must not be called from atomic context.
>> + */
>> +int max77686_read_gpios(struct max77686_platform_data *pdata)
>> +{
>> + int buck_default_idx = pdata->buck_default_idx;
>
> Remove this, it adds very little.
>
Ok.
>> + int result = 0;
>> + int i;
>> +
>> + for (i = 0; i < ARRAY_SIZE(pdata->buck_gpio_dvs); i++) {
>> + struct gpio_desc *gpio = pdata->buck_gpio_dvs[i];
>> +
>> + /* OK if some GPIOs aren't defined; we'll use default */
>> + if (IS_ERR(gpio)) {
>> + result |= buck_default_idx & (1 << i);
>
> s/(1 << i)/BIT(i)/
>
Ok.
>> + continue;
>> + }
>> +
>> + if (gpiod_get_value_cansleep(gpio))
>> + result |= 1 << i;
>
> Same here.
>
Ok.
>> + }
>> +
>> + return result;
>> +}
>> +EXPORT_SYMBOL_GPL(max77686_read_gpios);
>> +
>> static struct max77686_platform_data *max77686_i2c_parse_dt_pdata(struct device
>> *dev)
>> {
>> + struct device_node *np = dev->of_node;
>> struct max77686_platform_data *pd;
>>
>> pd = devm_kzalloc(dev, sizeof(*pd), GFP_KERNEL);
>> @@ -111,6 +223,13 @@ static struct max77686_platform_data *max77686_i2c_parse_dt_pdata(struct device
>> return NULL;
>>
>> dev->platform_data = pd;
>> +
>> + /* Read default index and ignore errors, since default is 0 */
>> + of_property_read_u32(np, "max77686,pmic-buck-default-dvs-idx",
>
> If it doesn't already have one, this needs a DT Ack and associated
> documentation.
>
Yes, these DT binding properties are documented in Patch 17/24 "mfd: max77686:
Add documentation for DVS bindings" and I've cc'ed devicetree@xxxxxxxxxxxxxxx so
hopefully I can get some feedback/ack from DT maintainers.
>> + &pd->buck_default_idx);
>> +
>> + max77686_dt_parse_dvs_gpio(dev);
>
> Bring code back into here and remove the call.
>
Sure, will do.
>> return pd;
>> }
>>
>> diff --git a/include/linux/mfd/max77686.h b/include/linux/mfd/max77686.h
>> index 4cbcc13..46a736b 100644
>> --- a/include/linux/mfd/max77686.h
>> +++ b/include/linux/mfd/max77686.h
>> @@ -99,15 +99,17 @@ struct max77686_platform_data {
>> struct max77686_opmode_data *opmode_data;
>>
>> /*
>> - * GPIO-DVS feature is not enabled with the current version of
>> - * MAX77686 driver. Buck2/3/4_voltages[0] is used as the default
>> - * voltage at probe. DVS/SELB gpios are set as OUTPUT-LOW.
>> + * GPIO-DVS feature is not fully enabled with the current version of
>> + * MAX77686 driver, but the driver does support using a DVS index other
>> + * than the default of 0.
>> */
>> - int buck234_gpio_dvs[3]; /* GPIO of [0]DVS1, [1]DVS2, [2]DVS3 */
>> - int buck234_gpio_selb[3]; /* [0]SELB2, [1]SELB3, [2]SELB4 */
>> - unsigned int buck2_voltage[8]; /* buckx_voltage in uV */
>> - unsigned int buck3_voltage[8];
>> - unsigned int buck4_voltage[8];
>> + struct gpio_desc *buck_gpio_dvs[3]; /* GPIO of [0]DVS1, [1]DVS2, [2]DVS3 */
>> + int buck_default_idx; /* Default value of DVS1, 2, 3 */
>> +
>> + struct gpio_desc *buck_gpio_selb[3]; /* Buck regulators 2, 3, 4 */
>> };
>>
>> +extern int max77686_setup_gpios(struct device *dev);
>> +extern int max77686_read_gpios(struct max77686_platform_data *pdata);
>> +
>> #endif /* __LINUX_MFD_MAX77686_H */
>
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
