Re: [PATCH] devicetree: Add generic IOMMU device tree bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tuesday 20 May 2014 17:39:12 Dave Martin wrote:
> On Tue, May 20, 2014 at 04:26:59PM +0100, Will Deacon wrote:
> > On Tue, May 20, 2014 at 02:23:47PM +0100, Arnd Bergmann wrote:
> > > 	Bit#   33222222 22221111 11111100 00000000
> > > 	       10987654 32109876 54321098 76543210
> > > phys.hi cell:  npt000ss bbbbbbbb dddddfff rrrrrrrr
> > > phys.mid cell: hhhhhhhh hhhhhhhh hhhhhhhh hhhhhhhh
> > > phys.lo cell:  llllllll llllllll llllllll llllllll
> > > 
> > > where:
> > > n is 0 if the address is relocatable, 1 otherwise
> > > p is 1 if the addressable region is "prefetchable", 0 otherwise
> > > t is 1 if the address is aliased (for non-relocatable I/O),
> > >  below 1 MB (for Memory), or below 64 KB (for relocatable I/O).
> > > ss is the space code, denoting the address space
> > > bbbbbbbb is the 8-bit Bus Number
> > > ddddd is the 5-bit Device Number
> > > fff is the 3-bit Function Number
> > > rrrrrrrr is the 8-bit Register Number
> > > hh...hh is a 32-bit unsigned number
> > > ll...ll is a 32-bit unsigned number
> > > 
> > > We can ignore n, p, t and r here, and use the same format for a DMA
> > > address, then define an empty "dma-ranges" property. That would
> > > imply that using b/d/f is sufficient to identify each master at the
> > > iommu. Any device outside of the PCI host but connected to the same
> > > iommu can use the same notation to list the logical b/d/f that gets
> > > sent to the IOMMU in bus master transactions.
> > > 
> > > Do you think this is sufficient for the ARM SMMU, or do we need
> > > something beyond that?
> > 
> > I think it can define the common-cases for the existing implementations,
> > yes. I anticipate Stream-IDs becoming > 16-bit in the near future though,
> > so we'd need extra bits if we're describing other devices coming into the
> > SMMU.
> > 
> > Note that we already have a binding for the current SMMU driver, so I'm not
> > really in a position to shift over to a new binding until the next version of
> > the SMMU architecture comes along...
> 
> How much code relies on the meaning of the nptsbdf bits?

Not much at all, I think this was defined mostly for open firmware
client interfaces, which we don't use with FDT.

n, t and r are probably only used in PCI functions that are listed
in DT, not in the host bridge.

b/d/f I think is mostly used for the interrupt-maps property, when
describing hardwired interrupts.

p and s are used when setting up the translation for inbound MMIO
and PIO.

	Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  Powered by Linux