Hi Chanwoo,
On 09.05.2014 03:06, Chanwoo Choi wrote:
On 04/26/2014 09:51 AM, Tomasz Figa wrote:
On 25.04.2014 03:16, Chanwoo Choi wrote:
[snip]
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a7";
+ reg = <0>;
+ clock-frequency = <1000000000>;
+ };
Why only one CPU? I believe Exynos3250 is dual core.
I'll add cpu1 information.
Also are physical IDs of the cores really 0 and 1? On Exynos4210 for example they are 0x900 and 0x901, while on Exynos4212 they are 0xa00 and 0xa01. Please check this.
The 'reg' property means only hardware id(hwid) of CPU.
You can check it on arm_dt_init_cpu_maps() in arch/arm/kernel/devtree.c.h.
or Documentation/devicetree/bindings/arm/cpus.txt.
Well, as described in Documentation/devicetree/bindings/arm/cpus.txt, on
32-bit ARM v7 or later CPUs the "reg" property should be equal to the
lower 24-bits of MPIDR value of given CPU, which in addition to core ID
includes also cluster ID, which can be non-zero, even on single cluster
SoCs (like it is on Exynos4210 and 4x12).
+ };
+
+ fixed-rate-clocks {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
[snip]
+ cmu: clock-controller@10030000 {
+ compatible = "samsung,exynos3250-cmu";
+ reg = <0x10030000 0x20000>;
+ #clock-cells = <1>;
+ };
+
+ rtc@10070000 {
Please add label to the node, so it can be referenced from board dts files added later (using the method I explained above).
OK, I'll add lable as following:
rtc_0: rtc@10070000 {
There is no need to suffix the RTC with _0, as there is just one RTC in
the SoC. So in this case rtc: rtc@10070000 will be enough.
+ compatible = "samsung,s3c6410-rtc";
+ reg = <0x10070000 0x100>;
+ interrupts = <0 73 0>, <0 74 0>;
+ status = "disabled";
+ };
[snip]
+ adc: adc@126C0000 {
+ compatible = "samsung,exynos-adc-v3";
+ reg = <0x126C0000 0x100>, <0x10020718 0x4>;
+ interrupts = <0 137 0>;
+ clock-names = "adc", "sclk_tsadc";
+ clocks = <&cmu CLK_TSADC>, <&cmu CLK_SCLK_TSADC>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ status = "disabled";
+ };
+
+ serial@13800000 {
Please add label.
OK, I'll add lable as following:
serial_0: serial@13800000 {
OK. In this case there are multiple instances of serial controller
available so the _0 suffix is fine.
+ compatible = "samsung,exynos4210-uart";
+ reg = <0x13800000 0x100>;
+ interrupts = <0 109 0>;
+ clocks = <&cmu CLK_UART0>, <&cmu CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+ status = "disabled";
+ };
+
+ serial@13810000 {
OK, I'll add lable as following:
serial_1: serial@13800000 {
OK.
Thanks for your review.
You're welcome. Thanks for addressing my comments.
Best regards,
Tomasz
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
