On Wednesday 30 April 2014 08:54 AM, Vivek Gautam wrote:
> Hi Kishon, Tomasz,
>
>
> On Mon, Apr 28, 2014 at 11:47 AM, Vivek Gautam <gautam.vivek@xxxxxxxxxxx> wrote:
>> Add a new driver for the USB 3.0 PHY on Exynos5 series of SoCs.
>> The new driver uses the generic PHY framework and will interact
>> with DWC3 controller present on Exynos5 series of SoCs.
>> Thereby, removing old phy-samsung-usb3 driver and related code
>> used untill now which was based on usb/phy framework.
>>
>> Signed-off-by: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
>> ---
>
> Does this patch looks Ok now ?
fine by me. Tomasz, if you are OK with this patch pls give you Acked by.
Cheers
Kishon
> Actually we plan to get this in for 3.16, so if things are good we can
> get a go ahead for this :-)
>
>>
>> Changes from v6:
>> - Addressed review comments:
>> -- Sorted config entries in Kconfig and Makefile
>> -- Made #define to_usbdrd_phy(inst) to a static inline routine.
>> -- Restructured exynos5_rate_to_clk() as suggested.
>> -- Amended 'val' field for regmap_update_bits() in the routine
>> exynos5_usbdrd_phy_isol().
>> -- Removed sentinel entry from exynos5_usbdrd_phy_cfg[] struct.
>> -- Removed check for 'match' entry in probe().
>>
>> .../devicetree/bindings/phy/samsung-phy.txt | 40 ++
>> drivers/phy/Kconfig | 11 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-exynos5-usbdrd.c | 627 ++++++++++++++++++++
>> 4 files changed, 679 insertions(+)
>> create mode 100644 drivers/phy/phy-exynos5-usbdrd.c
>>
>> diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>> index b422e38..51efe4c 100644
>> --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt
>> +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt
>> @@ -114,3 +114,43 @@ Example:
>> compatible = "samsung,exynos-sataphy-i2c";
>> reg = <0x38>;
>> };
>> +
>> +Samsung Exynos5 SoC series USB DRD PHY controller
>> +--------------------------------------------------
>> +
>> +Required properties:
>> +- compatible : Should be set to one of the following supported values:
>> + - "samsung,exynos5250-usbdrd-phy" - for exynos5250 SoC,
>> + - "samsung,exynos5420-usbdrd-phy" - for exynos5420 SoC.
>> +- reg : Register offset and length of USB DRD PHY register set;
>> +- clocks: Clock IDs array as required by the controller
>> +- clock-names: names of clocks correseponding to IDs in the clock property;
>> + Required clocks:
>> + - phy: main PHY clock (same as USB DRD controller i.e. DWC3 IP clock),
>> + used for register access.
>> + - ref: PHY's reference clock (usually crystal clock), used for
>> + PHY operations, associated by phy name. It is used to
>> + determine bit values for clock settings register.
>> + For Exynos5420 this is given as 'sclk_usbphy30' in CMU.
>> +- samsung,pmu-syscon: phandle for PMU system controller interface, used to
>> + control pmu registers for power isolation.
>> +- samsung,pmu-offset: phy power control register offset to pmu-system-controller
>> + base.
>> +- #phy-cells : from the generic PHY bindings, must be 1;
>> +
>> +For "samsung,exynos5250-usbdrd-phy" and "samsung,exynos5420-usbdrd-phy"
>> +compatible PHYs, the second cell in the PHY specifier identifies the
>> +PHY id, which is interpreted as follows:
>> + 0 - UTMI+ type phy,
>> + 1 - PIPE3 type phy,
>> +
>> +Example:
>> + usb3_phy: usbphy@12100000 {
>> + compatible = "samsung,exynos5250-usbdrd-phy";
>> + reg = <0x12100000 0x100>;
>> + clocks = <&clock 286>, <&clock 1>;
>> + clock-names = "phy", "ref";
>> + samsung,pmu-syscon = <&pmu_system_controller>;
>> + samsung,pmu-offset = <0x704>;
>> + #phy-cells = <1>;
>> + };
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 3bb05f1..daa1707 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -159,6 +159,17 @@ config PHY_EXYNOS5250_USB2
>> particular SoC is compiled in the driver. In case of Exynos 5250 four
>> phys are available - device, host, HSIC0 and HSIC.
>>
>> +config PHY_EXYNOS5_USBDRD
>> + tristate "Exynos5 SoC series USB DRD PHY driver"
>> + depends on ARCH_EXYNOS5 && OF
>> + depends on HAS_IOMEM
>> + select GENERIC_PHY
>> + select MFD_SYSCON
>> + help
>> + Enable USB DRD PHY support for Exynos 5 SoC series.
>> + This driver provides PHY interface for USB 3.0 DRD controller
>> + present on Exynos5 SoC series.
>> +
>> config PHY_XGENE
>> tristate "APM X-Gene 15Gbps PHY support"
>> depends on HAS_IOMEM && OF && (ARM64 || COMPILE_TEST)
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index 2faf78e..333ba98 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -17,4 +17,5 @@ obj-$(CONFIG_PHY_SAMSUNG_USB2) += phy-samsung-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS4210_USB2) += phy-exynos4210-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS4X12_USB2) += phy-exynos4x12-usb2.o
>> obj-$(CONFIG_PHY_EXYNOS5250_USB2) += phy-exynos5250-usb2.o
>> +obj-$(CONFIG_PHY_EXYNOS5_USBDRD) += phy-exynos5-usbdrd.o
>> obj-$(CONFIG_PHY_XGENE) += phy-xgene.o
>> diff --git a/drivers/phy/phy-exynos5-usbdrd.c b/drivers/phy/phy-exynos5-usbdrd.c
>> new file mode 100644
>> index 0000000..bc381e3
>> --- /dev/null
>> +++ b/drivers/phy/phy-exynos5-usbdrd.c
>> @@ -0,0 +1,627 @@
>> +/*
>> + * Samsung EXYNOS5 SoC series USB DRD PHY driver
>> + *
>> + * Phy provider for USB 3.0 DRD controller on Exynos5 SoC series
>> + *
>> + * Copyright (C) 2014 Samsung Electronics Co., Ltd.
>> + * Author: Vivek Gautam <gautam.vivek@xxxxxxxxxxx>
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/io.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/phy/phy.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/mutex.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/regmap.h>
>> +
>> +/* Exynos USB PHY registers */
>> +#define EXYNOS5_FSEL_9MHZ6 0x0
>> +#define EXYNOS5_FSEL_10MHZ 0x1
>> +#define EXYNOS5_FSEL_12MHZ 0x2
>> +#define EXYNOS5_FSEL_19MHZ2 0x3
>> +#define EXYNOS5_FSEL_20MHZ 0x4
>> +#define EXYNOS5_FSEL_24MHZ 0x5
>> +#define EXYNOS5_FSEL_50MHZ 0x7
>> +
>> +/* EXYNOS5: USB 3.0 DRD PHY registers */
>> +#define EXYNOS5_DRD_LINKSYSTEM 0x04
>> +
>> +#define LINKSYSTEM_FLADJ_MASK (0x3f << 1)
>> +#define LINKSYSTEM_FLADJ(_x) ((_x) << 1)
>> +#define LINKSYSTEM_XHCI_VERSION_CONTROL BIT(27)
>> +
>> +#define EXYNOS5_DRD_PHYUTMI 0x08
>> +
>> +#define PHYUTMI_OTGDISABLE BIT(6)
>> +#define PHYUTMI_FORCESUSPEND BIT(1)
>> +#define PHYUTMI_FORCESLEEP BIT(0)
>> +
>> +#define EXYNOS5_DRD_PHYPIPE 0x0c
>> +
>> +#define EXYNOS5_DRD_PHYCLKRST 0x10
>> +
>> +#define PHYCLKRST_EN_UTMISUSPEND BIT(31)
>> +
>> +#define PHYCLKRST_SSC_REFCLKSEL_MASK (0xff << 23)
>> +#define PHYCLKRST_SSC_REFCLKSEL(_x) ((_x) << 23)
>> +
>> +#define PHYCLKRST_SSC_RANGE_MASK (0x03 << 21)
>> +#define PHYCLKRST_SSC_RANGE(_x) ((_x) << 21)
>> +
>> +#define PHYCLKRST_SSC_EN BIT(20)
>> +#define PHYCLKRST_REF_SSP_EN BIT(19)
>> +#define PHYCLKRST_REF_CLKDIV2 BIT(18)
>> +
>> +#define PHYCLKRST_MPLL_MULTIPLIER_MASK (0x7f << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF (0x19 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF (0x32 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF (0x68 << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF (0x7d << 11)
>> +#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF (0x02 << 11)
>> +
>> +#define PHYCLKRST_FSEL_UTMI_MASK (0x7 << 5)
>> +#define PHYCLKRST_FSEL_PIPE_MASK (0x7 << 8)
>> +#define PHYCLKRST_FSEL(_x) ((_x) << 5)
>> +#define PHYCLKRST_FSEL_PAD_100MHZ (0x27 << 5)
>> +#define PHYCLKRST_FSEL_PAD_24MHZ (0x2a << 5)
>> +#define PHYCLKRST_FSEL_PAD_20MHZ (0x31 << 5)
>> +#define PHYCLKRST_FSEL_PAD_19_2MHZ (0x38 << 5)
>> +
>> +#define PHYCLKRST_RETENABLEN BIT(4)
>> +
>> +#define PHYCLKRST_REFCLKSEL_MASK (0x03 << 2)
>> +#define PHYCLKRST_REFCLKSEL_PAD_REFCLK (0x2 << 2)
>> +#define PHYCLKRST_REFCLKSEL_EXT_REFCLK (0x3 << 2)
>> +
>> +#define PHYCLKRST_PORTRESET BIT(1)
>> +#define PHYCLKRST_COMMONONN BIT(0)
>> +
>> +#define EXYNOS5_DRD_PHYREG0 0x14
>> +#define EXYNOS5_DRD_PHYREG1 0x18
>> +
>> +#define EXYNOS5_DRD_PHYPARAM0 0x1c
>> +
>> +#define PHYPARAM0_REF_USE_PAD BIT(31)
>> +#define PHYPARAM0_REF_LOSLEVEL_MASK (0x1f << 26)
>> +#define PHYPARAM0_REF_LOSLEVEL (0x9 << 26)
>> +
>> +#define EXYNOS5_DRD_PHYPARAM1 0x20
>> +
>> +#define PHYPARAM1_PCS_TXDEEMPH_MASK (0x1f << 0)
>> +#define PHYPARAM1_PCS_TXDEEMPH (0x1c)
>> +
>> +#define EXYNOS5_DRD_PHYTERM 0x24
>> +
>> +#define EXYNOS5_DRD_PHYTEST 0x28
>> +
>> +#define PHYTEST_POWERDOWN_SSP BIT(3)
>> +#define PHYTEST_POWERDOWN_HSP BIT(2)
>> +
>> +#define EXYNOS5_DRD_PHYADP 0x2c
>> +
>> +#define EXYNOS5_DRD_PHYUTMICLKSEL 0x30
>> +
>> +#define PHYUTMICLKSEL_UTMI_CLKSEL BIT(2)
>> +
>> +#define EXYNOS5_DRD_PHYRESUME 0x34
>> +#define EXYNOS5_DRD_LINKPORT 0x44
>> +
>> +/* Power isolation defined in power management unit */
>> +#define EXYNOS5_USBDRD_PMU_ISOL BIT(0)
>> +
>> +#define KHZ 1000
>> +#define MHZ (KHZ * KHZ)
>> +
>> +enum exynos5_usbdrd_phy_id {
>> + EXYNOS5_DRDPHY_UTMI,
>> + EXYNOS5_DRDPHY_PIPE3,
>> + EXYNOS5_DRDPHYS_NUM,
>> +};
>> +
>> +struct phy_usb_instance;
>> +struct exynos5_usbdrd_phy;
>> +
>> +struct usbdrd_phy_config {
>> + u32 id;
>> + void (*phy_isol)(struct phy_usb_instance *inst, u32 on);
>> + void (*phy_init)(struct exynos5_usbdrd_phy *phy_drd);
>> + unsigned int (*set_refclk)(struct phy_usb_instance *inst);
>> +};
>> +
>> +struct exynos5_usbdrd_phy_drvdata {
>> + const struct usbdrd_phy_config *phy_cfg;
>> +};
>> +
>> +/**
>> + * struct exynos5_usbdrd_phy - driver data for USB 3.0 PHY
>> + * @dev: pointer to device instance of this platform device
>> + * @reg_phy: usb phy controller register memory base
>> + * @clk: phy clock for register access
>> + * @drv_data: pointer to SoC level driver data structure
>> + * @phys[]: array for 'EXYNOS5_DRDPHYS_NUM' number of PHY
>> + * instances each with its 'phy' and 'phy_cfg'.
>> + * @extrefclk: frequency select settings when using 'separate
>> + * reference clocks' for SS and HS operations
>> + * @ref_clk: reference clock to PHY block from which PHY's
>> + * operational clocks are derived
>> + * @ref_rate: rate of above reference clock
>> + */
>> +struct exynos5_usbdrd_phy {
>> + struct device *dev;
>> + void __iomem *reg_phy;
>> + struct clk *clk;
>> + const struct exynos5_usbdrd_phy_drvdata *drv_data;
>> + struct phy_usb_instance {
>> + struct phy *phy;
>> + u32 index;
>> + struct regmap *reg_pmu;
>> + u32 pmu_offset;
>> + const struct usbdrd_phy_config *phy_cfg;
>> + } phys[EXYNOS5_DRDPHYS_NUM];
>> + u32 extrefclk;
>> + struct clk *ref_clk;
>> +};
>> +
>> +static inline
>> +struct exynos5_usbdrd_phy *to_usbdrd_phy(struct phy_usb_instance *inst)
>> +{
>> + return container_of((inst), struct exynos5_usbdrd_phy,
>> + phys[(inst)->index]);
>> +}
>> +
>> +/*
>> + * exynos5_rate_to_clk() converts the supplied clock rate to the value that
>> + * can be written to the phy register.
>> + */
>> +static unsigned int exynos5_rate_to_clk(unsigned long rate, u32 *reg)
>> +{
>> + /* EXYNOS5_FSEL_MASK */
>> +
>> + switch (rate) {
>> + case 9600 * KHZ:
>> + *reg = EXYNOS5_FSEL_9MHZ6;
>> + break;
>> + case 10 * MHZ:
>> + *reg = EXYNOS5_FSEL_10MHZ;
>> + break;
>> + case 12 * MHZ:
>> + *reg = EXYNOS5_FSEL_12MHZ;
>> + break;
>> + case 19200 * KHZ:
>> + *reg = EXYNOS5_FSEL_19MHZ2;
>> + break;
>> + case 20 * MHZ:
>> + *reg = EXYNOS5_FSEL_20MHZ;
>> + break;
>> + case 24 * MHZ:
>> + *reg = EXYNOS5_FSEL_24MHZ;
>> + break;
>> + case 50 * MHZ:
>> + *reg = EXYNOS5_FSEL_50MHZ;
>> + break;
>> + default:
>> + return -EINVAL;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void exynos5_usbdrd_phy_isol(struct phy_usb_instance *inst,
>> + unsigned int on)
>> +{
>> + unsigned int val;
>> +
>> + if (!inst->reg_pmu)
>> + return;
>> +
>> + val = on ? 0 : EXYNOS5_USBDRD_PMU_ISOL;
>> +
>> + regmap_update_bits(inst->reg_pmu, inst->pmu_offset,
>> + EXYNOS5_USBDRD_PMU_ISOL, val);
>> +}
>> +
>> +/*
>> + * Sets the pipe3 phy's clk as EXTREFCLK (XXTI) which is internal clock
>> + * from clock core. Further sets multiplier values and spread spectrum
>> + * clock settings for SuperSpeed operations.
>> + */
>> +static unsigned int
>> +exynos5_usbdrd_pipe3_set_refclk(struct phy_usb_instance *inst)
>> +{
>> + static u32 reg;
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + /* restore any previous reference clock settings */
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + /* Use EXTREFCLK as ref clock */
>> + reg &= ~PHYCLKRST_REFCLKSEL_MASK;
>> + reg |= PHYCLKRST_REFCLKSEL_EXT_REFCLK;
>> +
>> + /* FSEL settings corresponding to reference clock */
>> + reg &= ~PHYCLKRST_FSEL_PIPE_MASK |
>> + PHYCLKRST_MPLL_MULTIPLIER_MASK |
>> + PHYCLKRST_SSC_REFCLKSEL_MASK;
>> + switch (phy_drd->extrefclk) {
>> + case EXYNOS5_FSEL_50MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>> + break;
>> + case EXYNOS5_FSEL_24MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>> + break;
>> + case EXYNOS5_FSEL_20MHZ:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x00));
>> + break;
>> + case EXYNOS5_FSEL_19MHZ2:
>> + reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
>> + PHYCLKRST_SSC_REFCLKSEL(0x88));
>> + break;
>> + default:
>> + dev_dbg(phy_drd->dev, "unsupported ref clk\n");
>> + break;
>> + }
>> +
>> + return reg;
>> +}
>> +
>> +/*
>> + * Sets the utmi phy's clk as EXTREFCLK (XXTI) which is internal clock
>> + * from clock core. Further sets the FSEL values for HighSpeed operations.
>> + */
>> +static unsigned int
>> +exynos5_usbdrd_utmi_set_refclk(struct phy_usb_instance *inst)
>> +{
>> + static u32 reg;
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + /* restore any previous reference clock settings */
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + reg &= ~PHYCLKRST_REFCLKSEL_MASK;
>> + reg |= PHYCLKRST_REFCLKSEL_EXT_REFCLK;
>> +
>> + reg &= ~PHYCLKRST_FSEL_UTMI_MASK |
>> + PHYCLKRST_MPLL_MULTIPLIER_MASK |
>> + PHYCLKRST_SSC_REFCLKSEL_MASK;
>> + reg |= PHYCLKRST_FSEL(phy_drd->extrefclk);
>> +
>> + return reg;
>> +}
>> +
>> +static void exynos5_usbdrd_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
>> +{
>> + u32 reg;
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> + /* Set Tx De-Emphasis level */
>> + reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>> + reg |= PHYPARAM1_PCS_TXDEEMPH;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> + reg &= ~PHYTEST_POWERDOWN_SSP;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> +}
>> +
>> +static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
>> +{
>> + u32 reg;
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> + /* Set Loss-of-Signal Detector sensitivity */
>> + reg &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
>> + reg |= PHYPARAM0_REF_LOSLEVEL;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> + /* Set Tx De-Emphasis level */
>> + reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
>> + reg |= PHYPARAM1_PCS_TXDEEMPH;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
>> +
>> + /* UTMI Power Control */
>> + writel(PHYUTMI_OTGDISABLE, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> + reg &= ~PHYTEST_POWERDOWN_HSP;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> +}
>> +
>> +static int exynos5_usbdrd_phy_init(struct phy *phy)
>> +{
>> + int ret;
>> + u32 reg;
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + ret = clk_prepare_enable(phy_drd->clk);
>> + if (ret)
>> + return ret;
>> +
>> + /* Reset USB 3.0 PHY */
>> + writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
>> + writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYRESUME);
>> +
>> + /*
>> + * Setting the Frame length Adj value[6:1] to default 0x20
>> + * See xHCI 1.0 spec, 5.2.4
>> + */
>> + reg = LINKSYSTEM_XHCI_VERSION_CONTROL |
>> + LINKSYSTEM_FLADJ(0x20);
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
>> +
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> + /* Select PHY CLK source */
>> + reg &= ~PHYPARAM0_REF_USE_PAD;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
>> +
>> + /* This bit must be set for both HS and SS operations */
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
>> + reg |= PHYUTMICLKSEL_UTMI_CLKSEL;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
>> +
>> + /* UTMI or PIPE3 specific init */
>> + inst->phy_cfg->phy_init(phy_drd);
>> +
>> + /* reference clock settings */
>> + reg = inst->phy_cfg->set_refclk(inst);
>> +
>> + /* Digital power supply in normal operating mode */
>> + reg |= PHYCLKRST_RETENABLEN |
>> + /* Enable ref clock for SS function */
>> + PHYCLKRST_REF_SSP_EN |
>> + /* Enable spread spectrum */
>> + PHYCLKRST_SSC_EN |
>> + /* Power down HS Bias and PLL blocks in suspend mode */
>> + PHYCLKRST_COMMONONN |
>> + /* Reset the port */
>> + PHYCLKRST_PORTRESET;
>> +
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + udelay(10);
>> +
>> + reg &= ~PHYCLKRST_PORTRESET;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + clk_disable_unprepare(phy_drd->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos5_usbdrd_phy_exit(struct phy *phy)
>> +{
>> + int ret;
>> + u32 reg;
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + ret = clk_prepare_enable(phy_drd->clk);
>> + if (ret)
>> + return ret;
>> +
>> + reg = PHYUTMI_OTGDISABLE |
>> + PHYUTMI_FORCESUSPEND |
>> + PHYUTMI_FORCESLEEP;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
>> +
>> + /* Resetting the PHYCLKRST enable bits to reduce leakage current */
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> + reg &= ~(PHYCLKRST_REF_SSP_EN |
>> + PHYCLKRST_SSC_EN |
>> + PHYCLKRST_COMMONONN);
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
>> +
>> + /* Control PHYTEST to remove leakage current */
>> + reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> + reg |= PHYTEST_POWERDOWN_SSP |
>> + PHYTEST_POWERDOWN_HSP;
>> + writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
>> +
>> + clk_disable_unprepare(phy_drd->clk);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos5_usbdrd_phy_power_on(struct phy *phy)
>> +{
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + dev_dbg(phy_drd->dev, "Request to power_on usbdrd_phy phy\n");
>> +
>> + clk_prepare_enable(phy_drd->ref_clk);
>> +
>> + /* Power-on PHY*/
>> + inst->phy_cfg->phy_isol(inst, 0);
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos5_usbdrd_phy_power_off(struct phy *phy)
>> +{
>> + struct phy_usb_instance *inst = phy_get_drvdata(phy);
>> + struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
>> +
>> + dev_dbg(phy_drd->dev, "Request to power_off usbdrd_phy phy\n");
>> +
>> + /* Power-off the PHY */
>> + inst->phy_cfg->phy_isol(inst, 1);
>> +
>> + clk_disable_unprepare(phy_drd->ref_clk);
>> +
>> + return 0;
>> +}
>> +
>> +static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
>> + struct of_phandle_args *args)
>> +{
>> + struct exynos5_usbdrd_phy *phy_drd = dev_get_drvdata(dev);
>> +
>> + if (WARN_ON(args->args[0] > EXYNOS5_DRDPHYS_NUM))
>> + return ERR_PTR(-ENODEV);
>> +
>> + return phy_drd->phys[args->args[0]].phy;
>> +}
>> +
>> +static struct phy_ops exynos5_usbdrd_phy_ops = {
>> + .init = exynos5_usbdrd_phy_init,
>> + .exit = exynos5_usbdrd_phy_exit,
>> + .power_on = exynos5_usbdrd_phy_power_on,
>> + .power_off = exynos5_usbdrd_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +const struct usbdrd_phy_config exynos5_usbdrd_phy_cfg[] = {
>> + {
>> + .id = EXYNOS5_DRDPHY_UTMI,
>> + .phy_isol = exynos5_usbdrd_phy_isol,
>> + .phy_init = exynos5_usbdrd_utmi_init,
>> + .set_refclk = exynos5_usbdrd_utmi_set_refclk,
>> + },
>> + {
>> + .id = EXYNOS5_DRDPHY_PIPE3,
>> + .phy_isol = exynos5_usbdrd_phy_isol,
>> + .phy_init = exynos5_usbdrd_pipe3_init,
>> + .set_refclk = exynos5_usbdrd_pipe3_set_refclk,
>> + },
>> +};
>> +
>> +const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
>> + .phy_cfg = exynos5_usbdrd_phy_cfg,
>> +};
>> +
>> +const struct exynos5_usbdrd_phy_drvdata exynos5250_usbdrd_phy = {
>> + .phy_cfg = exynos5_usbdrd_phy_cfg,
>> +};
>> +
>> +static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
>> + {
>> + .compatible = "samsung,exynos5250-usbdrd-phy",
>> + .data = &exynos5250_usbdrd_phy
>> + }, {
>> + .compatible = "samsung,exynos5420-usbdrd-phy",
>> + .data = &exynos5420_usbdrd_phy
>> + },
>> + { },
>> +};
>> +
>> +static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *node = dev->of_node;
>> + struct exynos5_usbdrd_phy *phy_drd;
>> + struct phy_provider *phy_provider;
>> + struct resource *res;
>> + const struct of_device_id *match;
>> + const struct exynos5_usbdrd_phy_drvdata *drv_data;
>> + struct regmap *reg_pmu;
>> + u32 pmu_offset;
>> + unsigned long ref_rate;
>> + int i, ret;
>> +
>> + phy_drd = devm_kzalloc(dev, sizeof(*phy_drd), GFP_KERNEL);
>> + if (!phy_drd)
>> + return -ENOMEM;
>> +
>> + dev_set_drvdata(dev, phy_drd);
>> + phy_drd->dev = dev;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + phy_drd->reg_phy = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(phy_drd->reg_phy))
>> + return PTR_ERR(phy_drd->reg_phy);
>> +
>> + match = of_match_node(exynos5_usbdrd_phy_of_match, pdev->dev.of_node);
>> +
>> + drv_data = match->data;
>> + phy_drd->drv_data = drv_data;
>> +
>> + phy_drd->clk = devm_clk_get(dev, "phy");
>> + if (IS_ERR(phy_drd->clk)) {
>> + dev_err(dev, "Failed to get clock of phy controller\n");
>> + return PTR_ERR(phy_drd->clk);
>> + }
>> +
>> + phy_drd->ref_clk = devm_clk_get(dev, "ref");
>> + if (IS_ERR(phy_drd->ref_clk)) {
>> + dev_err(dev, "Failed to get reference clock of usbdrd phy\n");
>> + return PTR_ERR(phy_drd->ref_clk);
>> + }
>> + ref_rate = clk_get_rate(phy_drd->ref_clk);
>> +
>> + ret = exynos5_rate_to_clk(ref_rate, &phy_drd->extrefclk);
>> + if (ret) {
>> + dev_err(phy_drd->dev, "Clock rate (%ld) not supported\n",
>> + ref_rate);
>> + return ret;
>> + }
>> +
>> + reg_pmu = syscon_regmap_lookup_by_phandle(dev->of_node,
>> + "samsung,pmu-syscon");
>> + if (IS_ERR(reg_pmu)) {
>> + dev_err(dev, "Failed to map PMU register (via syscon)\n");
>> + return PTR_ERR(reg_pmu);
>> + }
>> +
>> + ret = of_property_read_u32(node, "samsung,pmu-offset", &pmu_offset);
>> + if (ret) {
>> + dev_err(dev, "Missing pmu-offset for phy isolation\n");
>> + return ret;
>> + }
>> +
>> + dev_vdbg(dev, "Creating usbdrd_phy phy\n");
>> +
>> + for (i = 0; i < EXYNOS5_DRDPHYS_NUM; i++) {
>> + struct phy *phy = devm_phy_create(dev, &exynos5_usbdrd_phy_ops,
>> + NULL);
>> + if (IS_ERR(phy)) {
>> + dev_err(dev, "Failed to create usbdrd_phy phy\n");
>> + return PTR_ERR(phy);
>> + }
>> +
>> + phy_drd->phys[i].phy = phy;
>> + phy_drd->phys[i].index = i;
>> + phy_drd->phys[i].reg_pmu = reg_pmu;
>> + phy_drd->phys[i].pmu_offset = pmu_offset;
>> + phy_drd->phys[i].phy_cfg = &drv_data->phy_cfg[i];
>> + phy_set_drvdata(phy, &phy_drd->phys[i]);
>> + }
>> +
>> + phy_provider = devm_of_phy_provider_register(dev,
>> + exynos5_usbdrd_phy_xlate);
>> + if (IS_ERR(phy_provider)) {
>> + dev_err(phy_drd->dev, "Failed to register phy provider\n");
>> + return PTR_ERR(phy_provider);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static struct platform_driver exynos5_usb3drd_phy = {
>> + .probe = exynos5_usbdrd_phy_probe,
>> + .driver = {
>> + .of_match_table = exynos5_usbdrd_phy_of_match,
>> + .name = "exynos5_usb3drd_phy",
>> + .owner = THIS_MODULE,
>> + }
>> +};
>> +
>> +module_platform_driver(exynos5_usb3drd_phy);
>> +MODULE_DESCRIPTION("Samsung EXYNOS5 SoCs USB 3.0 DRD controller PHY driver");
>> +MODULE_AUTHOR("Vivek Gautam <gautam.vivek@xxxxxxxxxxx>");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_ALIAS("platform:exynos5_usb3drd_phy");
>> --
>> 1.7.10.4
>>
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
