Hi Vikas,
Basically same comments as for the series for Exynos5260. Also see more
comments inline.
On 27.03.2014 07:13, Vikas Sajjan wrote:
Adds Suspend-to-RAM support for EXYNOS5420
Signed-off-by: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
Signed-off-by: Vikas Sajjan <vikas.sajjan@xxxxxxxxxxx>
---
arch/arm/mach-exynos/pm.c | 148 ++++++++++++++++++++++----
arch/arm/mach-exynos/regs-pmu.h | 4 +-
arch/arm/plat-samsung/include/plat/map-s5p.h | 2 +
drivers/clk/samsung/clk-exynos5420.c | 32 ++++++
4 files changed, 167 insertions(+), 19 deletions(-)
diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
index 15af0ce..aa3c2c8 100644
--- a/arch/arm/mach-exynos/pm.c
+++ b/arch/arm/mach-exynos/pm.c
@@ -59,6 +59,16 @@ static struct sleep_save exynos_core_save[] = {
SAVE_ITEM(S5P_SROM_BC3),
};
+static struct sleep_save exynos5420_cpustate_save[] = {
+ SAVE_ITEM(EXYNOS5420_VA_CPU_STATE),
+};
+
+static struct sleep_save exynos5420_reg_save[] = {
+ SAVE_ITEM(EXYNOS5_SYS_DISP1_BLK_CFG),
+ SAVE_ITEM(S5P_PMU_SPARE3),
+};
+
+
/*
* GIC wake-up support
*/
@@ -81,7 +91,7 @@ static int exynos_irq_set_wake(struct irq_data *data, unsigned int state)
{
const struct exynos_wkup_irq *wkup_irq;
- if (soc_is_exynos5250())
+ if (soc_is_exynos5250() || soc_is_exynos5420())
wkup_irq = exynos5250_wkup_irq;
else
wkup_irq = exynos4_wkup_irq;
@@ -109,7 +119,15 @@ static int exynos_cpu_suspend(unsigned long arg)
outer_flush_all();
#endif
- if (soc_is_exynos5250())
+ /*
+ * Clear IRAM register for cpu state so that primary CPU does
+ * not enter low power start in U-Boot.
+ * This is specific to exynos5420 SoC only.
+ */
+ if (soc_is_exynos5420())
+ __raw_writel(0x0, EXYNOS5420_VA_CPU_STATE);
+
+ if (soc_is_exynos5250() || soc_is_exynos5420())
flush_cache_all();
/* issue the standby signal into the pm unit. */
@@ -135,6 +153,20 @@ static void exynos_pm_prepare(void)
tmp = __raw_readl(EXYNOS5_JPEG_MEM_OPTION);
tmp &= ~EXYNOS5_OPTION_USE_RETENTION;
__raw_writel(tmp, EXYNOS5_JPEG_MEM_OPTION);
+ } else if (soc_is_exynos5420()) {
+
nit: Unnecessary blank line.
+ s3c_pm_do_save(exynos5420_reg_save,
+ ARRAY_SIZE(exynos5420_reg_save));
+
+ /*
+ * The cpu state needs to be saved and restored so that the
+ * secondary CPUs will enter low power start. Though the U-Boot
+ * is setting the cpu state with low power flag, the kernel
+ * needs to restore it back in case, the primary cpu fails to
+ * suspend for any reason
+ */
+ s3c_pm_do_save(exynos5420_cpustate_save,
+ ARRAY_SIZE(exynos5420_cpustate_save));
}
/* Set value of power down register for sleep mode */
@@ -145,11 +177,34 @@ static void exynos_pm_prepare(void)
/* ensure at least INFORM0 has the resume address */
__raw_writel(virt_to_phys(exynos_cpu_resume), S5P_INFORM0);
+
+ if (soc_is_exynos5420()) {
+
+ tmp = __raw_readl(EXYNOS5_ARM_L2_OPTION);
+ tmp &= ~EXYNOS5_USE_RETENTION;
+ __raw_writel(tmp, EXYNOS5_ARM_L2_OPTION);
+
+ tmp = __raw_readl(EXYNOS5420_SFR_AXI_CGDIS1);
+ tmp |= EXYNOS5420_UFS;
+ __raw_writel(tmp, EXYNOS5420_SFR_AXI_CGDIS1);
+
+ tmp = __raw_readl(EXYNOS5420_ARM_COMMON_OPTION);
+ tmp &= ~EXYNOS5420_L2RSTDISABLE_VALUE;
+ __raw_writel(tmp, EXYNOS5420_ARM_COMMON_OPTION);
+ tmp = __raw_readl(EXYNOS5420_FSYS2_OPTION);
+ tmp |= EXYNOS5420_EMULATION;
+ __raw_writel(tmp, EXYNOS5420_FSYS2_OPTION);
+ tmp = __raw_readl(EXYNOS5420_PSGEN_OPTION);
+ tmp |= EXYNOS5420_EMULATION;
+ __raw_writel(tmp, EXYNOS5420_PSGEN_OPTION);
+ }
+
}
static int exynos_pm_suspend(void)
{
unsigned long tmp;
+ unsigned long cluster_id;
/* Setting Central Sequence Register for power down mode */
@@ -159,10 +214,20 @@ static int exynos_pm_suspend(void)
/* Setting SEQ_OPTION register */
- tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0);
- __raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION);
+ if (soc_is_exynos5420()) {
+ cluster_id = (read_cpuid(CPUID_MPIDR) >> 8) & 0xf;
+ if (!cluster_id)
+ __raw_writel(EXYNOS5420_ARM_USE_STANDBY_WFI0,
+ S5P_CENTRAL_SEQ_OPTION);
+ else
+ __raw_writel(EXYNOS5420_KFC_USE_STANDBY_WFI0,
+ S5P_CENTRAL_SEQ_OPTION);
+ } else {
+ tmp = (S5P_USE_STANDBY_WFI0 | S5P_USE_STANDBY_WFE0);
+ __raw_writel(tmp, S5P_CENTRAL_SEQ_OPTION);
+ }
- if (!soc_is_exynos5250()) {
+ if (!(soc_is_exynos5250() || soc_is_exynos5420())) {
/* Save Power control register */
asm ("mrc p15, 0, %0, c15, c0, 0"
: "=r" (tmp) : : "cc");
@@ -181,6 +246,15 @@ static void exynos_pm_resume(void)
{
unsigned long tmp;
+ if (soc_is_exynos5420()) {
+ /* Restore the IRAM register cpu state */
+ s3c_pm_do_restore(exynos5420_cpustate_save,
+ ARRAY_SIZE(exynos5420_cpustate_save));
+
+ __raw_writel(EXYNOS5420_USE_STANDBY_WFI_ALL,
+ S5P_CENTRAL_SEQ_OPTION);
+ }
+
/*
* If PMU failed while entering sleep mode, WFI will be
* ignored by PMU and then exiting cpu_do_idle().
@@ -196,7 +270,8 @@ static void exynos_pm_resume(void)
/* No need to perform below restore code */
goto early_wakeup;
}
- if (!soc_is_exynos5250()) {
+
+ if (!(soc_is_exynos5250() || soc_is_exynos5420())) {
/* Restore Power control register */
tmp = save_arm_register[0];
asm volatile ("mcr p15, 0, %0, c15, c0, 0"
@@ -212,25 +287,57 @@ static void exynos_pm_resume(void)
/* For release retention */
- __raw_writel((1 << 28), S5P_PAD_RET_MAUDIO_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_GPIO_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_UART_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_MMCA_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_MMCB_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_EBIA_OPTION);
- __raw_writel((1 << 28), S5P_PAD_RET_EBIB_OPTION);
+ if (soc_is_exynos5250()) {
+ __raw_writel((1 << 28), S5P_PAD_RET_MAUDIO_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_GPIO_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_UART_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_MMCA_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_MMCB_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_EBIA_OPTION);
+ __raw_writel((1 << 28), S5P_PAD_RET_EBIB_OPTION);
+ } else if (soc_is_exynos5420()) {
+ __raw_writel(1 << 28, EXYNOS_PAD_RET_DRAM_OPTION);
+ __raw_writel(1 << 28, EXYNOS_PAD_RET_MAUDIO_OPTION);
+ __raw_writel(1 << 28, EXYNOS_PAD_RET_JTAG_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_GPIO_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_UART_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_MMCA_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_MMCB_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_MMCC_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_HSI_OPTION);
+ __raw_writel(1 << 28, EXYNOS_PAD_RET_EBIA_OPTION);
+ __raw_writel(1 << 28, EXYNOS_PAD_RET_EBIB_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_SPI_OPTION);
+ __raw_writel(1 << 28, EXYNOS5420_PAD_RET_DRAM_COREBLK_OPTION);
+ }
if (soc_is_exynos5250())
s3c_pm_do_restore(exynos5_sys_save,
ARRAY_SIZE(exynos5_sys_save));
+ else if (soc_is_exynos5420())
+ s3c_pm_do_restore(exynos5420_reg_save,
+ ARRAY_SIZE(exynos5420_reg_save));
s3c_pm_do_restore_core(exynos_core_save, ARRAY_SIZE(exynos_core_save));
- if (IS_ENABLED(CONFIG_SMP) && !soc_is_exynos5250())
+ if (IS_ENABLED(CONFIG_SMP) &&
+ !soc_is_exynos5250() && !soc_is_exynos5420())
scu_enable(S5P_VA_SCU);
early_wakeup:
+ if (soc_is_exynos5420()) {
+ tmp = __raw_readl(EXYNOS5420_SFR_AXI_CGDIS1);
+ tmp &= ~EXYNOS5420_UFS;
+ __raw_writel(tmp, EXYNOS5420_SFR_AXI_CGDIS1);
+ tmp = __raw_readl(EXYNOS5420_FSYS2_OPTION);
+ tmp &= ~EXYNOS5420_EMULATION;
+ __raw_writel(tmp, EXYNOS5420_FSYS2_OPTION);
+ tmp = __raw_readl(EXYNOS5420_PSGEN_OPTION);
+ tmp &= ~EXYNOS5420_EMULATION;
+ __raw_writel(tmp, EXYNOS5420_PSGEN_OPTION);
+ }
+
/* Clear SLEEP mode set in INFORM1 */
__raw_writel(0x0, S5P_INFORM1);
@@ -312,10 +419,15 @@ void __init exynos_pm_init(void)
gic_arch_extn.irq_set_wake = exynos_irq_set_wake;
/* All wakeup disable */
- tmp = __raw_readl(S5P_WAKEUP_MASK);
- tmp |= ((0xFF << 8) | (0x1F << 1));
- __raw_writel(tmp, S5P_WAKEUP_MASK);
-
+ if (soc_is_exynos5420()) {
+ tmp = __raw_readl(S5P_WAKEUP_MASK);
+ tmp |= ((0x7F << 7) | (0x1F << 1));
+ __raw_writel(tmp, S5P_WAKEUP_MASK);
+ } else {
+ tmp = __raw_readl(S5P_WAKEUP_MASK);
+ tmp |= ((0xFF << 8) | (0x1F << 1));
+ __raw_writel(tmp, S5P_WAKEUP_MASK);
+ }
register_syscore_ops(&exynos_pm_syscore_ops);
suspend_set_ops(&exynos_suspend_ops);
}
diff --git a/arch/arm/mach-exynos/regs-pmu.h b/arch/arm/mach-exynos/regs-pmu.h
index cfbfc575..53eac2b 100644
--- a/arch/arm/mach-exynos/regs-pmu.h
+++ b/arch/arm/mach-exynos/regs-pmu.h
@@ -39,6 +39,7 @@
#define S5P_INFORM6 S5P_PMUREG(0x0818)
#define S5P_INFORM7 S5P_PMUREG(0x081C)
+#define S5P_PMU_SPARE3 S5P_PMUREG(0x090C)
#define EXYNOS_IROM_DATA2 S5P_PMUREG(0x0988)
#define S5P_ARM_CORE0_LOWPWR S5P_PMUREG(0x1000)
@@ -113,7 +114,6 @@
#define EXYNOS5_ARM_L2_OPTION S5P_PMUREG(0x2608)
#define EXYNOS5_USE_RETENTION BIT(4)
-
#define S5P_PAD_RET_MAUDIO_OPTION S5P_PMUREG(0x3028)
#define S5P_PAD_RET_GPIO_OPTION S5P_PMUREG(0x3108)
#define S5P_PAD_RET_UART_OPTION S5P_PMUREG(0x3128)
@@ -216,6 +216,8 @@
/* For EXYNOS5 */
+#define EXYNOS5_SYS_DISP1_BLK_CFG S5P_SYSREG(0x0214)
+
#define EXYNOS5_SYS_I2C_CFG S5P_SYSREG(0x0234)
#define EXYNOS5_AUTO_WDTRESET_DISABLE S5P_PMUREG(0x0408)
diff --git a/arch/arm/plat-samsung/include/plat/map-s5p.h b/arch/arm/plat-samsung/include/plat/map-s5p.h
index c186786..cfb150e 100644
--- a/arch/arm/plat-samsung/include/plat/map-s5p.h
+++ b/arch/arm/plat-samsung/include/plat/map-s5p.h
@@ -57,6 +57,8 @@
#define S3C_UART_OFFSET (0x400)
#endif
+#define EXYNOS5420_VA_CPU_STATE (S5P_VA_SYSRAM + 0x28)
+
Please, no more static addresses. This should be defined as an offset to
SYSRAM in the source file that actually uses it.
#include <plat/map-s3c.h>
#endif /* __ASM_PLAT_MAP_S5P_H */
diff --git a/drivers/clk/samsung/clk-exynos5420.c b/drivers/clk/samsung/clk-exynos5420.c
index 60b2681..965ea69 100644
--- a/drivers/clk/samsung/clk-exynos5420.c
+++ b/drivers/clk/samsung/clk-exynos5420.c
@@ -101,6 +101,19 @@
#define KPLL_CON0 0x28100
#define SRC_KFC 0x28200
#define DIV_KFC0 0x28500
+#define SRC_MASK_CPERI 0x04300
Please keep the registers sorted...
+#define SRC_MASK_TOP0 0x10300
+#define SRC_MASK_TOP1 0x10304
+#define SRC_MASK_TOP2 0x10308
+#define SRC_MASK_TOP7 0x1031C
+#define SRC_MASK_MAU 0x10334
+#define SRC_MASK_FSYS 0x10340
+#define SRC_MASK_PERIC0 0x10350
+#define SRC_MASK_PERIC1 0x10354
+#define SRC_MASK_ISP 0x10370
+#define GATE_BUS_DISP1 0x10728
+#define GATE_IP_PERIC 0x10950
+
/* list of PLLs */
enum exynos5420_plls {
@@ -180,11 +193,30 @@ static unsigned long exynos5420_clk_regs[] __initdata = {
DIV_KFC0,
};
+static const struct samsung_clk_reg_dump exynos5420_set_clksrc[] = {
+ { .offset = SRC_MASK_CPERI, .value = 0xffffffff, },
+ { .offset = SRC_MASK_TOP0, .value = 0x11111111, },
+ { .offset = SRC_MASK_TOP1, .value = 0x11101111, },
+ { .offset = SRC_MASK_TOP2, .value = 0x11111110, },
+ { .offset = SRC_MASK_TOP7, .value = 0x00111100, },
+ { .offset = SRC_MASK_DISP10, .value = 0x11111110, },
+ { .offset = SRC_MASK_MAU, .value = 0x10000000, },
+ { .offset = SRC_MASK_FSYS, .value = 0x11111110, },
+ { .offset = SRC_MASK_PERIC0, .value = 0x11111110, },
+ { .offset = SRC_MASK_PERIC1, .value = 0x11111100, },
+ { .offset = SRC_MASK_ISP, .value = 0x11111000, },
+ { .offset = GATE_BUS_DISP1, .value = 0xffffffff, },
+ { .offset = GATE_IP_PERIC, .value = 0xffffffff, },
+};
+
+
static int exynos5420_clk_suspend(void)
{
samsung_clk_save(reg_base, exynos5420_save,
ARRAY_SIZE(exynos5420_clk_regs));
+ samsung_clk_restore(reg_base, exynos5420_set_clksrc,
+ ARRAY_SIZE(exynos5420_set_clksrc));
nit: You could align ARRAY_SIZE to the same indentation level as the
call to samsung_clk_save() above.
Best regards,
Tomasz
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
