Am Montag, den 31.03.2014, 11:36 +0200 schrieb Marek Vasut: > On Monday, March 31, 2014 at 11:28:29 AM, Lucas Stach wrote: > > Am Sonntag, den 30.03.2014, 19:36 +0200 schrieb Marek Vasut: > > > On Friday, March 28, 2014 at 05:52:53 PM, Lucas Stach wrote: > > > > The glue around the core designware IP is significantly > > > > different between the Exynos and i.MX implementation, > > > > which is reflected in the DT bindings. > > > > > > > > This changes the i.MX6 binding to reuse as much as > > > > possible from the common designware binding and > > > > removes old cruft. > > > > > > > > I removed the optional GPIOs with the following reasoning: > > > > - disable-gpio: endpoint specific GPIO, not currently > > > > > > > > wired up in any code. Should be handled by the PCI device > > > > driver, not the host controller driver. > > > > > > > > - wake-up-gpio: same as above. > > > > - power-on-gpio: No user in any upstream DT. This should > > > > > > > > be handled by a regulator which shouldn't be controlled > > > > by the host driver, but rather by the PCI device driver. > > > > > > This power-on-gpio should indeed be handled by the regulator, but the > > > regulator cannot be handled by the PCIe device driver. This > > > power-on-gpio must be operated on per-slot basis if I understand it > > > correctly, so it cannot be controlled by the host controller driver > > > either. > > > > > > The reason why this cannot be controlled by the device driver is that if > > > the device is powered down, it won't be detected on the PCIe bus, thus > > > it cannot enable the regulator which will power up the slot the device > > > is sitting in. > > > > So we are on the same page with regard to a GPIO being the wrong > > abstraction for this, I think. > > Yes. > > > For the regulator part I would argue that PCI is a bus that is built > > around the ability to inspect the bus and detect devices on the bus at > > probe time, so any regulator that's powering a PCI device should be > > boot-on. > > This thing about regulator being boot-on should really be documented. > > Moreover, I think it's a waste of power to keep the devices ON on boot even if > the PCIe bus was not started (yet). The bus might not be started at all and the > regulators would still be ON, which would be quite a waste. > It's the exact same behavior that you get on x86: all devices are powered after boot, once you loaded a device driver it may choose to turn the device off. I don't think it makes sense to deviate here for the sake of being embedded and special. > > Only after the device driver is loaded it should be able to fetch the > > regulator to power down/up the device as it wishes. In the x86 world > > this is AFAIK done using ACPI methods. > > > > I think the host controller driver has no business in controlling the > > device power, more so as there possibly could be a lot of devices on the > > bus even with a single host lane. > > The power should be controlled per-slot, but I don't know how to model that. > Note that there might be a PCIe device with a switch popped into a single slot, > which makes things much more interesting. In such case, you need to power up the > slot and neither of the downstream devices should control the power regulator of > that slot. > We could just add the regulator to the PCI hierarchy in the DT and handle it similar to IRQs where we just walk up the DT starting from the device until we find the matching IRQ/regulator. Still for this to work with a regulator shared between several devices, all the device drivers have to be aware of the regulator. Otherwise a single device may choose to power down and erroneously cut power to a sibling device, where the driver hasn't requested the regulator. In all those scenarios the host controller driver still would not have any business dealing with the regulator. Same situation as with the legacy IRQs, that aren't handled by the host driver, but just routed to the right instance through the DT. Regards, Lucas -- Pengutronix e.K. | Lucas Stach | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-5076 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |