On Wed, Mar 19, 2014 at 10:32:48PM +0000, Byungho An wrote: > Mark Rutland <mark.rutland@xxxxxxx> : > > On Tue, Mar 18, 2014 at 04:27:46PM +0000, Byungho An wrote: > > > Mark Rutland <mark.rutland@xxxxxxx> : > > > > Hi, > > > > > > > > As a general note it's helpful for devicetree to be Cc'd on the > > > > entire > > > series > > > > (though the binding document should be a separate patch) as it > > > > provides > > > useful > > > > context for reviewing the binding. > > > OK. > > > > > > > > > > > On Tue, Mar 18, 2014 at 06:47:13AM +0000, Byungho An wrote: > > > > > From: Siva Reddy <siva.kallam@xxxxxxxxxxx> > > > > > > > > > > This patch adds binding document for SXGBE ethernet driver via > > > device-tree. > > > > > > > > > > Signed-off-by: Siva Reddy Kallam <siva.kallam@xxxxxxxxxxx> > > > > > Signed-off-by: Byungho An <bh74.an@xxxxxxxxxxx> > > > > > --- > > > > > .../devicetree/bindings/net/samsung-sxgbe.txt | 53 > > > > > ++++++++++++++++++++ > > > > > 1 file changed, 53 insertions(+) > > > > > create mode 100644 > > > > > Documentation/devicetree/bindings/net/samsung-sxgbe.txt > > > > > > > > > > diff --git > > > > > a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt > > > > > b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt > > > > > new file mode 100644 > > > > > index 0000000..ca27947 > > > > > --- /dev/null > > > > > +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt > > > > > @@ -0,0 +1,53 @@ > > > > > +* Samsung 10G Ethernet driver (SXGBE) > > > > > + > > > > > +Required properties: > > > > > +- compatible: Should be "samsung,sxgbe-v2.0a" > > > > > +- reg: Address and length of the register set for the device > > > > > +- interrupt-parent: Should be the phandle for the interrupt > > > > > +controller > > > > > + that services interrupts for this device > > > > > +- interrupts: Should contain the SXGBE interrupts > > > > > + These interrupts are ordered by fixed and follows variable > > > > > + trasmit DMA interrupts, receive DMA interrupts and lpi interrupt. > > > > > + index 0 - this is fixed common interrupt of SXGBE and it is > > > > > +always > > > > > + available. > > > > > + index 1 to 25 - 8 variable trasmit interrupts, variable 16 > > > > > +receive > > > > > interrupts > > > > > + and 1 optional lpi interrupt. > > > > > +- phy-mode: String, operation mode of the PHY interface. > > > > > + Supported values are: "xaui", "gmii". > > > > > +- samsung,pbl: Integer, Programmable Burst Length. > > > > > + Supported values are 1, 2, 4, 8, 16, or 32. > > > > > > > > There's no need to abbreviate to "pbl". > > > > > > > > Is this a property of the hardware, or configuration that the kernel > > > > will > > > program > > > > in? If the latter, why can the kernel not choose? > > > Yes, this is hardware property > > > > Ok. > > > > > > > > > > > > > > +- samsung,fixed-burst: Boolean, Program the DMA to use the fixed > > > > > +burst mode > > > > > +- samsung,burst-map: Integer, Program the possible bursts > > > > > +supported by sxgbe > > > > > + This is an interger and represents allowable DMA bursts when > > > > > +fixed > > > burst. > > > > > + Allowable range is 0x00-0x3F. This field is valid only when > > > > > +fixed burst is > > > > > + enabled, otherwise ignored. > > > > > > > > If that's the case, why not have just this property and have it > > > > imply the > > > use of > > > > fixed burst mode? > > > OK. It will be implemented in next patch set. > > > > > > > > > > > When is it necessary to use fixed burst mode? > > > This is the configurable mode of DMA an used internally by hardware to > > > fetch data from platform bus > > > > Sure, but that doesn't describe when it is necessary. Is this the way the > DMA > > was configured at integration time, or the way the kernel should configure > it? > It is needed when fixed length of burst is needed. > if it is not configured, the length of burst will be variable(not fixed). > Anyway, I'll add description more for it. And when is it necessary to have a fixed length of burst? Is this a property of the system, or the conenction of the system to another? > > > > > If the latter, is it absolutely necessary for correctness to use fixed-burst > mode? > > Or is it just always sensible to use it if available? > It is not absolutely necessary, as I mentioned above. The description above does not make this clear. > > > > > What does the driver do if fixed burst mode is not available? Would this > work in > > the presence of fixed-burt mode? > Fixed burst mode is always available so driver doesn't need to care about it. > > > > > I'm not arguing to remove these properties. I'd just like to understand if > all > > you're describing is the presence of a feature or that the use of the > feature is > > absolutely necessary for correctness. > OK > > > > > I'm perfectly happy for Linux to always decide to use these features if > available. > > > > > > > > > > > > > > +- samsung,adv-addr-mode: Boolean, Program the DMA to use Enhanced > > > > > +address > > > > > mode. > > > > > > > > When would this be selected, and why can the kernel not choose? > > > Kernel doesn't have the provision to find out a way to select this. > > > So, need to pass from DT > > > > Likewise, it is always absolutely necessary, or just always sensible to use > > enhanced address mode if present? > Not always necessary. When extended address mode is needed, it can be set in > the DT. When is this needed? Cheers, Mark. -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |