Florian Fainelli <f.fainelli@xxxxxxxxx> wrote :
> 2014-03-18 11:19 GMT-07:00 Byungho An <bh74.an@xxxxxxxxxxx>:
> > From: Siva Reddy <siva.kallam@xxxxxxxxxxx>
> >
> > This patch adds binding document for SXGBE ethernet driver via device-tree.
> >
> > Signed-off-by: Siva Reddy Kallam <siva.kallam@xxxxxxxxxxx>
> > Signed-off-by: Byungho An <bh74.an@xxxxxxxxxxx>
> > ---
> > .../devicetree/bindings/net/samsung-sxgbe.txt | 52 ++++++++++++++++++++
> > 1 file changed, 52 insertions(+)
> > create mode 100644
> > Documentation/devicetree/bindings/net/samsung-sxgbe.txt
> >
> > diff --git a/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
> > b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
> > new file mode 100644
> > index 0000000..340eff6
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/samsung-sxgbe.txt
> > @@ -0,0 +1,52 @@
> > +* Samsung 10G Ethernet driver (SXGBE)
> > +
> > +Required properties:
> > +- compatible: Should be "samsung,sxgbe-v2.0a"
> > +- reg: Address and length of the register set for the device
> > +- interrupt-parent: Should be the phandle for the interrupt
> > +controller
> > + that services interrupts for this device
> > +- interrupts: Should contain the SXGBE interrupts
> > + These interrupts are ordered by fixed and follows variable
> > + trasmit DMA interrupts, receive DMA interrupts and lpi interrupt.
> > + index 0 - this is fixed common interrupt of SXGBE and it is always
> > + available.
> > + index 1 to 25 - 8 variable trasmit interrupts, variable 16 receive
> > +interrupts
> > + and 1 optional lpi interrupt.
> > +- phy-mode: String, operation mode of the PHY interface.
>
> You should reference
> Documentation/devicetree/bindings/net/ethernet.txt which is more thorough about what this is about.
OK.
>
> > + Supported values are: "xaui", "gmii".
>
> xaui is not documented in
> Documentation/devicetree/bindings/net/ethernet.txt, nor is it supported in include/linux/phy.h and drivers/of/of_net.c, that should
> be part of the patchset.
OK. It will be changed to xgmii and xaui support patch will be posted later.
>
> > +- samsung,pbl: Integer, Programmable Burst Length.
> > + Supported values are 1, 2, 4, 8, 16, or 32.
> > +- samsung,burst-map: Integer, Program the possible bursts supported
> > +by sxgbe
> > + This is an interger and represents allowable DMA bursts when fixed burst.
> > + Allowable range is 0x00-0x3F. This field is valid only when fixed
> > +burst is
> > + enabled, otherwise ignored.
> > +- samsung,adv-addr-mode: Boolean, Program the DMA to use Enhanced address mode.
> > +- samsung,force-thresh-dma-mode: Boolean, Force DMA to use the
> > +threshold mode
> > + for both tx and rx
> > +- samsung,force-sf-dma-mode: Boolean, Force DMA to use the Store and
> > +Forward
> > + mode for both tx and rx. This flag is ignored if force-thresh-dma-mode is set.
> > +- samsung,phy-addr: Integer, Address of the PHY attached with SXGBE.
>
> Please don't use a custom property for that, use a phy-handle which points to an ePAPR compliant Ethernet PHY device tree node as
> described in Documentation/devicetree/bindings/net/phy.txt.
OK.
>
> > +
> > +Optional properties:
> > +- mac-address: 6 bytes, mac address
>
> Did you intend to use 'local-mac-address'. 'mac-address' is described by ePAPR as:
>
> "Specifies the MAC address that was last used by the boot program.
> This property should be
> used in cases where the MAC address assigned to the device by the boot program is different from the local-mac-address property.
> This property shall be used only if the value differs from local-mac-address property value."
>
> Does your bootloader really do something which falls into that description? If not, use 'local-mac-address'.
In my case, bootloader assigns mac address so mac-address is suitable according to Documentation/devicetree/binings/net/ethernet.txt.
>
> > +
> > +Example:
> > +
> > + aliases {
> > + ethernet0 = <&sxgbe0>;
> > + };
> > +
> > + sxgbe0: ethernet@1a040000 {
> > + compatible = "samsung,sxgbe-v2.0a";
> > + reg = <0 0x1a040000 0 0x10000>;
> > + interrupt-parent = <&gic>;
> > + interrupts = <0 209 4>, <0 185 4>, <0 186 4>, <0 187 4>,
> > + <0 188 4>, <0 189 4>, <0 190 4>, <0 191 4>,
> > + <0 192 4>, <0 193 4>, <0 194 4>, <0 195 4>,
> > + <0 196 4>, <0 197 4>, <0 198 4>, <0 199 4>,
> > + <0 200 4>, <0 201 4>, <0 202 4>, <0 203 4>,
> > + <0 204 4>, <0 205 4>, <0 206 4>, <0 207 4>,
> > + <0 208 4>, <0 210 4>;
> > + mac-address = [000000000000]; /* Filled in by U-Boot
> > + */
>
> The preferred way to format this is:
> mac-address = [ 00 00 00 00 00 00 ]; even better is something directly usable in case people copy/paste this example such as
> 00 11 22 33 44 55.
OK.
>
> > + phy-mode = "xaui";
>
> Your example is lacking a corresponding Ethernet PHY address/node.
OK. Will be updated.
> --
> Florian
> --
> To unsubscribe from this list: send the line "unsubscribe netdev" in the body of a message to majordomo@xxxxxxxxxxxxxxx More
> majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
