Hi, On Friday 11 of October 2013 15:49:04 Jingoo Han wrote: > On Tuesday, October 08, 2013 8:45 PM, Yuvaraj Kumar wrote: > > On Fri, Oct 4, 2013 at 6:03 AM, Jingoo Han <jg1.han@xxxxxxxxxxx> wrote: > > > On Thursday, October 03, 2013 8:32 PM, Bartlomiej Zolnierkiewicz wrote: > > >> On Tuesday, October 01, 2013 12:03:01 PM Yuvaraj Kumar C D wrote: > > >> > Exynos5250 contains one Synopsys AHCI SATA controller.The avalaible > > >> > ahci_platform driver is not sufficient to handle the AHCI PHY and PHY > > >> > clock related initialization. > > >> > > > >> > This patch adds exynos specific ahci sata driver,contained the exynos > > >> > specific initialized codes, re-use the generic ahci_platform driver, and > > >> > keep the generic ahci_platform driver clean as much as possible. > > >> > > > >> > This patch depends on the below patch > > >> > [1].drivers: phy: add generic PHY framework > > >> > by Kishon Vijay Abraham I<kishon@xxxxxx> > > >> > > > >> > Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx> > > >> > --- > > >> > drivers/ata/Kconfig | 9 ++ > > >> > drivers/ata/Makefile | 1 + > > >> > drivers/ata/ahci_exynos.c | 226 +++++++++++++++++++++++++++++++++++++++++++++ > > >> > 3 files changed, 236 insertions(+) > > >> > create mode 100644 drivers/ata/ahci_exynos.c > > >> > > > > > > > > > > [.....] > > > > > >> > + priv->phy = devm_phy_get(dev , "sata-phy"); > > >> > + if (IS_ERR(priv->phy)) > > >> > + return PTR_ERR(priv->phy); > > > > > > [.....] > > > > > >> Also please take a look at the following patch: > > >> > > >> https://lkml.org/lkml/2013/9/19/173 > > >> > > >> it adds PHY support to ahci_platform driver, maybe it can be used > > >> for your needs as well. > > > > > > I also agree with Bartlomiej Zolnierkiewicz's opinion. > > > 'ahci_exynos.c' just calls PHY API, without any additional control > > > for Exynos AHCI IP. > > In addition to PHY handling,it also deals with the special clock > > sclk_sata which is not dealt in ahci_platform.c(certainly exynos > > specific). > > Handling the special clock 'sclk_sata' is another issue. > Please, look at that other 'sclk_*'s are handled. > Also, if possible, please add 'the code handling the special clock' > to 'ahci_platform.c'. > > > > > Morever there is a wrapper driver to handle the platform specific > > things for the sata.Please refer the patch[1] > > [1]ata: ti_sata: Add Texas Instruments SATA Wrapper driver > > https://lkml.org/lkml/2013/9/19/166 > > As Roger Quadros mentioned, 'ti_sata' driver will be dropped. > > > [2]ahci_imx: add ahci sata support on imx platforms > > > > 'ahci_imx' is necessary, because 'ahci_imx' controls some > specific registers. > > However, 'ahci_exynos.c' does not control any registers. > > > I think, if we have platform specific driver like ahci_xxx.c , it > > would be better to handle the sata PHY in ahci_xxx.c so that we can > > retain and re-use the ahci_platform.c as it is. > > I think that the platform specific driver like ahci_xxx.c is not > necessary, because 'ahci_exynos.c' does not control any special > registers. My big +1 to all the JIngoo's points above. Best regards, Tomasz -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |