Hi Arnd,
Thanks for replying :-)
On Sunday 22 September 2013 03:33 AM, Arnd Bergmann wrote:
> On Saturday 21 September 2013, Kishon Vijay Abraham I wrote:
>> {
>> u32 val;
>> void __iomem *val1;
>> void __iomem *dbi_base = pp->dbi_base;
>>
>> /* Program viewport 0 : INBOUND : MEMORY*/
>> val = PCIE_ATU_REGION_INBOUND | (0 & 0xF);
>> dw_pcie_writel_rc(pp, val, dbi_base + PCIE_ATU_VIEWPORT);
>> val1 = ioremap(0x80000000, 0x5fffffff);
>
> The ioremap here makes no sense at all, and I suspect it will fail anyway,
> because you exhaust the vmalloc area size, but since the value is not
> used anywhere, it won't matter.
>
>> dw_pcie_writel_rc(pp, 0x80000000, dbi_base + PCIE_ATU_LOWER_BASE);
>> dw_pcie_writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_BASE);
>> /* in_mem_size must be in power of 2 */
>> dw_pcie_writel_rc(pp, 0x5FFFFFFF, dbi_base + PCIE_ATU_LIMIT);
>> dw_pcie_writel_rc(pp, 0x80000000, dbi_base + PCIE_ATU_LOWER_TARGET);
>> dw_pcie_writel_rc(pp, 0, dbi_base + PCIE_ATU_UPPER_TARGET);
>
> These numbers need to come from somewhere, you shouldn't just hardcode them,
right. I'm still in the process of getting it work ;-)
>
> I guess you should either program an inbound window covering the entire 64-bit
> address space, or you should look at the top-level "memory" nodes to find
> the location of physical RAM.
>
> I can't see anything wrong with the way it's set up though, unless you have
> an IOMMU. Can you confirm that there is no IOMMU (aka SMMU) in your system
> that handles the PCIe root complex?
There is a MMU for PCIe root complex but that's disabled.
>
>> I somehow starting to doubt the DMA address programmed in the ethernet card
>> which is in my RAM address range (0x80000000 to 0xBFFFFFFF). Should this
>> address be programmed in the BAR of the ethernet card? How should it be done?
>
> No, it should not be in the BAR. The ethernet device driver calls dma_map_*
> or pci_map_* interfaces to get a valid token that can be passed into the
> device registers that are starting the DMA. You have to ensure that the
> dma_map_ops for the device return the value that is set up in the translation.
>
> The normal case is an identity mapping between device DMA space and host
> memory space, i.e. PCIE_ATU_LOWER_TARGET == PCIE_ATU_LOWER_BASE, so
> in the dma_map_single implementation, phys_addr_t == dma_addr_t.
>
> If you set up the dma_addr_t space to start at 0 instead, you have to add
> the offset in the dma_map_ops.
My DMA address is in 0x80000000 to 0xBFFFFFFF range and I program my inbound
translation for this range. Not sure what is missing still :-(
Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
