On 17-06-2013 02:46, Amit Daniel Kachhap wrote: > This patch adds support for h/w mode calibration in the TMU controller. > soc's like 5440 support this features. > > Acked-by: Jonghwa Lee <jonghwa3.lee@xxxxxxxxxxx> > Acked-by: Kukjin Kim <kgene.kim@xxxxxxxxxxx> > Signed-off-by: Amit Daniel Kachhap <amit.daniel@xxxxxxxxxxx> > --- > drivers/thermal/samsung/exynos_tmu.c | 15 +++++++++++++++ > drivers/thermal/samsung/exynos_tmu.h | 6 ++++++ > drivers/thermal/samsung/exynos_tmu_data.c | 2 ++ > drivers/thermal/samsung/exynos_tmu_data.h | 2 ++ > 4 files changed, 25 insertions(+), 0 deletions(-) > > diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c > index af0e6ca..7a259f4 100644 > --- a/drivers/thermal/samsung/exynos_tmu.c > +++ b/drivers/thermal/samsung/exynos_tmu.c > @@ -73,6 +73,9 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp) > struct exynos_tmu_platform_data *pdata = data->pdata; > int temp_code; > > + if (pdata->cal_mode == HW_MODE) > + return temp; > + > if (data->soc == SOC_ARCH_EXYNOS4210) > /* temp should range between 25 and 125 */ > if (temp < 25 || temp > 125) { > @@ -107,6 +110,9 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) > struct exynos_tmu_platform_data *pdata = data->pdata; > int temp; > > + if (pdata->cal_mode == HW_MODE) > + return temp_code; > + > if (data->soc == SOC_ARCH_EXYNOS4210) > /* temp_code should range between 75 and 175 */ > if (temp_code < 75 || temp_code > 175) { > @@ -155,6 +161,9 @@ static int exynos_tmu_initialize(struct platform_device *pdev) > if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) > __raw_writel(1, data->base + reg->triminfo_ctrl); > > + if (pdata->cal_mode == HW_MODE) > + goto skip_calib_data; > + > /* Save trimming info in order to perform calibration */ > if (data->soc == SOC_ARCH_EXYNOS5440) { > /* > @@ -190,6 +199,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) > (pdata->efuse_value >> reg->triminfo_85_shift) & > EXYNOS_TMU_TEMP_MASK; > > +skip_calib_data: > if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) { > dev_err(&pdev->dev, "Invalid max trigger level\n"); > goto out; > @@ -319,6 +329,11 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) > con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift); > } > > + if (pdata->cal_mode == HW_MODE) { > + con &= ~(reg->calib_mode_mask << reg->calib_mode_shift); > + con |= pdata->cal_type << reg->calib_mode_shift; cal_type is an enum and you don't set any constant value to those enumerations. are you sure you want to rely on it for bit field handling? > + } > + > if (on) { > con |= (1 << reg->core_en_shift); > interrupt_en = > diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h > index 73aaed7..abfa1eb 100644 > --- a/drivers/thermal/samsung/exynos_tmu.h > +++ b/drivers/thermal/samsung/exynos_tmu.h > @@ -88,6 +88,10 @@ enum soc_type { > * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl > register. > * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register. > + * @calib_mode_shift: shift bits of calibration mode value in tmu_ctrl > + register. > + * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl > + register. > * @therm_trip_tq_en_shift: shift bits of thermal trip enable by TQ pin in > tmu_ctrl register. > * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register. > @@ -149,6 +153,8 @@ struct exynos_tmu_registers { > u32 therm_trip_en_shift; > u32 buf_slope_sel_shift; > u32 buf_slope_sel_mask; > + u32 calib_mode_shift; > + u32 calib_mode_mask; > u32 therm_trip_tq_en_shift; > u32 core_en_shift; > > diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c > index b34e726..47c5d6b 100644 > --- a/drivers/thermal/samsung/exynos_tmu_data.c > +++ b/drivers/thermal/samsung/exynos_tmu_data.c > @@ -189,6 +189,8 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { > .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, > .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, > .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, > + .calib_mode_shift = EXYNOS_TMU_CALIB_MODE_SHIFT, > + .calib_mode_mask = EXYNOS_TMU_CALIB_MODE_MASK, > .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, > .tmu_status = EXYNOS5440_TMU_S0_7_STATUS, > .tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP, > diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h > index 43ce5fb..dc7feb5 100644 > --- a/drivers/thermal/samsung/exynos_tmu_data.h > +++ b/drivers/thermal/samsung/exynos_tmu_data.h > @@ -75,6 +75,8 @@ > #define EXYNOS_TMU_TRIP_MODE_SHIFT 13 > #define EXYNOS_TMU_TRIP_MODE_MASK 0x7 > #define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12 > +#define EXYNOS_TMU_CALIB_MODE_SHIFT 4 > +#define EXYNOS_TMU_CALIB_MODE_MASK 0x3 > > #define EXYNOS_TMU_INTEN_RISE0_SHIFT 0 > #define EXYNOS_TMU_INTEN_RISE1_SHIFT 4 > -- You have got to be excited about what you are doing. (L. Lamport) Eduardo Valentin
Attachment:
signature.asc
Description: OpenPGP digital signature