Hi .
On Fri, May 17, 2013 at 5:26 PM, <jonghwa3.lee@xxxxxxxxxxx> wrote:
> Hi, Amit
> On 2013년 05월 14일 18:58, Amit Daniel Kachhap wrote:
>
>> TMU urgently sends active-high signal (thermal trip) to PMU, and thermal
>> tripping by hardware logic. Thermal tripping means that PMU cuts off the
>> whole power of SoC by controlling external voltage regulator.
>>
>> Acked-by: Kukjin Kim <kgene.kim@xxxxxxxxxxx>
>> Signed-off-by: Jonghwan Choi <jhbird.choi@xxxxxxxxxxx>
>> Signed-off-by: Amit Daniel Kachhap <amit.daniel@xxxxxxxxxxx>
>> ---
>> drivers/thermal/samsung/exynos_tmu.c | 8 +++++++-
>> drivers/thermal/samsung/exynos_tmu_data.c | 2 ++
>> 2 files changed, 9 insertions(+), 1 deletions(-)
>>
>> diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c
>> index 5f8f189..479d61e 100644
>> --- a/drivers/thermal/samsung/exynos_tmu.c
>> +++ b/drivers/thermal/samsung/exynos_tmu.c
>> @@ -84,6 +84,7 @@
>> #define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12)
>> #define EXYNOS_TMU_TRIP_MODE_SHIFT 13
>> #define EXYNOS_TMU_TRIP_MODE_MASK 0x7
>> +#define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12
>>
>> #define EXYNOS_TMU_INTEN_RISE0_SHIFT 0
>> #define EXYNOS_TMU_INTEN_RISE1_SHIFT 4
>> @@ -186,7 +187,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> {
>> struct exynos_tmu_data *data = platform_get_drvdata(pdev);
>> struct exynos_tmu_platform_data *pdata = data->pdata;
>> - unsigned int status, trim_info;
>> + unsigned int status, trim_info, con;
>> unsigned int rising_threshold = 0, falling_threshold = 0;
>> int ret = 0, threshold_code, i, trigger_levs = 0;
>>
>> @@ -251,6 +252,11 @@ static int exynos_tmu_initialize(struct platform_device *pdev)
>> falling_threshold |=
>> threshold_code << 8 * i;
>> }
>> + if (pdata->trigger_type[i] != HW_TRIP)
>> + continue;
>
>
> As you know, HW trip can be used when only the most last level of threshold
> temperature is set. (exynos4412 : 4th, exynos 5440 : 5th threshold level). So it
> wouldn't work properly, even if we enable HW trip according to pre-defined
> trigger type not to HW trip threshold temperature. To enable HW trip, we just
> need to check whether if HW trip threshold temperature level is defined.
>
> if (trigger_level[HW_TRIP_LEVEL])
> enable HW trip
Yes you are right. I will include this change in the next version.
Thanks,
Amit Daniel
>
> Thanks,
> Jonghwa
>
>> + con = readl(data->base + EXYNOS_TMU_REG_CONTROL);
>> + con |= (1 << EXYNOS_TMU_THERM_TRIP_EN_SHIFT);
>> + writel(con, data->base + EXYNOS_TMU_REG_CONTROL);
>> }
>>
>> writel(rising_threshold,
>> diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c
>> index ee6a3c9..6b937f5 100644
>> --- a/drivers/thermal/samsung/exynos_tmu_data.c
>> +++ b/drivers/thermal/samsung/exynos_tmu_data.c
>> @@ -64,6 +64,7 @@ struct exynos_tmu_platform_data const exynos5250_default_tmu_data = {
>> .trigger_levels[0] = 85,
>> .trigger_levels[1] = 103,
>> .trigger_levels[2] = 110,
>> + .trigger_levels[3] = 120,
>> .trigger_enable[0] = 1,
>> .trigger_enable[1] = 1,
>> .trigger_enable[2] = 1,
>> @@ -71,6 +72,7 @@ struct exynos_tmu_platform_data const exynos5250_default_tmu_data = {
>> .trigger_type[0] = 0,
>> .trigger_type[1] = 0,
>> .trigger_type[2] = 1,
>> + .trigger_type[3] = 2,
>> .gain = 8,
>> .reference_voltage = 16,
>> .noise_cancel_mode = 4,
>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
