Amit,
On 26-03-2013 07:34, Amit Daniel Kachhap wrote:
This sensor registers 3 instance of the tmu controller with the thermal zone
and hence reports 3 temperature output. This driver supports upto five trip
points. For critical threshold the driver uses the core driver thermal
framework for shutdown and for non-critical threshold it invokes the hw based
frequency clipping limits. Because of such differences with the existing 4210
tmu controller, exynos5440 tmu driver is added in a new file.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@xxxxxxxxxxx>
---
drivers/thermal/samsung/Kconfig | 9 +
drivers/thermal/samsung/Makefile | 1 +
drivers/thermal/samsung/exynos5440_thermal.c | 713 ++++++++++++++++++++++++++
This driver does not compile as module:
ERROR: "exynos_report_trigger"
[drivers/thermal/samsung/exynos5440_thermal.ko] undefined!
ERROR: "exynos_get_frequency_level"
[drivers/thermal/samsung/exynos5440_thermal.ko] undefined!
ERROR: "exynos_unregister_thermal"
[drivers/thermal/samsung/exynos5440_thermal.ko] undefined!
Besides, this driver is pretty similar to 4210 driver. Are you you
cannot isolate the difference into config data? Again, check the driver
design for TI SoC thermal (drivers/staging/ti-soc-thermal/ on linux-next)
3 files changed, 723 insertions(+), 0 deletions(-)
create mode 100644 drivers/thermal/samsung/exynos5440_thermal.c
diff --git a/drivers/thermal/samsung/Kconfig b/drivers/thermal/samsung/Kconfig
index cefe693..0c7b4eb 100644
--- a/drivers/thermal/samsung/Kconfig
+++ b/drivers/thermal/samsung/Kconfig
@@ -20,4 +20,13 @@ config EXYNOS4210_THERMAL
initialises the TMU controller and registers/unregisters with exynos
common thermal layer.
+config EXYNOS5440_THERMAL
+ tristate "Temperature sensor on Samsung EXYNOS 5440 SOC"
+ depends on SOC_EXYNOS5440
+ help
+ If you say yes here you can enable TMU (Thermal Management Unit)
+ support on SAMSUNG EXYNOS 5440 series of SoC. This option initialises
+ the TMU controller and registers/unregisters with exynos common
+ thermal layer.
+
endif
diff --git a/drivers/thermal/samsung/Makefile b/drivers/thermal/samsung/Makefile
index d51d0c2..53230cf 100644
--- a/drivers/thermal/samsung/Makefile
+++ b/drivers/thermal/samsung/Makefile
@@ -3,3 +3,4 @@
#
obj-$(CONFIG_EXYNOS_COMMON) += exynos_common.o
obj-$(CONFIG_EXYNOS4210_THERMAL) += exynos4210_thermal.o
+obj-$(CONFIG_EXYNOS5440_THERMAL) += exynos5440_thermal.o
diff --git a/drivers/thermal/samsung/exynos5440_thermal.c b/drivers/thermal/samsung/exynos5440_thermal.c
new file mode 100644
index 0000000..a3c75d3
--- /dev/null
+++ b/drivers/thermal/samsung/exynos5440_thermal.c
@@ -0,0 +1,713 @@
+/*
+ * exynos5440_thermal.c - Samsung EXYNOS 5440 TMU
+ * (Thermal Management Unit)
+ *
+ * Copyright (C) 2013 Samsung Electronics
+ * Amit Daniel Kachhap <amit.daniel@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/cpufreq.h>
+#include <linux/cpu_cooling.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/kobject.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+#include <linux/workqueue.h>
+#include <linux/platform_data/exynos_thermal.h>
+
+#include "exynos_common.h"
+
+
+/* Exynos5440 specific registers */
+#define TMU_S0_7_TRIM 0x0118
+#define TMU_S0_7_CTRL 0x0138
+#define TMU_S0_7_DEBUG 0x0158
+#define TMU_S0_7_STATUS 0x0178
+#define TMU_S0_7_COUNTER0 0x0198
+#define TMU_S0_7_COUNTER1 0x01b8
+#define TMU_S0_7_COUNTER2 0x01d8
+#define TMU_S0_7_COUNTER3 0x01f8
+#define TMU_S0_7_TEMP 0x0208
+#define TMU_S0_7_TH0 0x0228
+#define TMU_S0_7_TH1 0x0248
+#define TMU_S0_7_TH2 0x0268
+#define TMU_S0_7_PTEMP0 0x0288
+#define TMU_S0_7_PTEMP1 0x02a8
+#define TMU_S0_7_PTEMP2 0x02c8
+#define TMU_S0_7_PTEMP3 0x02e8
+#define TMU_S0_7_EVTEN 0x0308
+#define TMU_S0_7_IRQEN 0x0328
+#define TMU_S0_7_IRQ 0x0348
+#define TMU_IRQ_STATUS 0x0368
+#define TMU_PMIN 0x036c
+#define TMU_TEMP 0x0370
+#define TMU_MISC 0x0374
+
+/* Exynos5440 specific mask and shifts */
+#define TMU_TEMP_MASK 0xff
+
+#define TMU_TRIM_DATA_25C_SHIFT 0x0
+#define TMU_TRIM_DATA_85C_SHIFT 0x8
+
+#define TMU_BUF_VREF_SEL_MASK 0x1f
+#define TMU_BUF_VREF_SEL_SHIFT 24
+#define TMU_THERM_TRIP_MODE_MASK 0x7
+#define TMU_THERM_TRIP_MODE_SHIFT 13
+#define TMU_THERM_TRIP_EN_SHIFT 12
+#define TMU_BUF_SLOPE_SEL_MASK 0Xf
+#define TMU_BUF_SLOPE_SEL_SHIFT 8
+#define TMU_THERM_IRQ_MODE_SHIFT 7
+#define TMU_CALIB_MODE_MASK 0x3
+#define TMU_CALIB_MODE_SHIFT 4
+#define TMU_FILTER_MODE_MASK 0x7
+#define TMU_FILTER_MODE_SHIFT 1
+#define TMU_SENSOR_EN_SHIFT 0
+#define TMU_SENSOR_ENABLE 0x1
+
+#define TMU_EMU_EN_SHIFT 0
+#define TMU_TEMP_EMU_SHIFT 8
+#define TMU_EMUL_ENABLE 1
+
+#define TMU_STATUS_IDLE_SHIFT 0
+
+#define TMU_TIME_MASK 0xffff
+#define TMU_TIME_OF_SHIFT 16
+#define TMU_TIME_ON_SHIFT 0
+
+#define TMU_CURRENT_TEMP_SHIFT 0
+#define TMU_FILTERED_TEMP_SHIFT 8
+#define TMU_RAW_TEMP_SHIFT 16
+#define TMU_TEMP_SEQNUM 24
+
+#define TMU_THRES_RISE0_SHIFT 0
+#define TMU_THRES_RISE1_SHIFT 8
+#define TMU_THRES_RISE2_SHIFT 16
+#define TMU_THRES_RISE3_SHIFT 24
+
+#define TMU_THRES_FALL0_SHIFT 0
+#define TMU_THRES_FALL1_SHIFT 8
+#define TMU_THRES_FALL2_SHIFT 16
+#define TMU_THRES_FALL3_SHIFT 24
+
+#define TMU_THRES_RISE4_SHIFT 24
+
+#define TMU_RISE_EVTEN_MASK 0xf
+#define TMU_RISE_EVTEN_SHIFT 0
+#define TMU_FALL_EVTEN_MASK 0xf
+#define TMU_FALL_EVTEN_SHIFT 4
+
+#define TMU_RISE_IRQEN_MASK 0xf
+#define TMU_RISE_IRQEN_SHIFT 0
+#define TMU_FALL_IRQEN_MASK 0xf
+#define TMU_FALL_IRQEN_SHIFT 4
+#define TMU_CLEAR_RISE_INT TMU_RISE_IRQEN_MASK
+#define TMU_CLEAR_FALL_INT (TMU_FALL_IRQEN_MASK << 4)
+
+#define TMU_PMIN_MASK 0x7
+#define TMU_PMIN0_SHIFT 0
+#define TMU_PMIN1_SHIFT 4
+#define TMU_PMIN2_SHIFT 8
+#define TMU_PMIN3_SHIFT 12
+#define TMU_PMIN_SHIFT(x) (4 * x)
+#define TMU_TPMIN_SHIFT 16
+
+#define TMU_TEMP_MAX_SHIFT 0
+#define TMU_MAX_RISE_LEVEL 4
+#define TMU_MAX_FALL_LEVEL 4
+#define TMU_MAX_SENSOR 8
+
+#define TMU_DEF_CODE_TO_TEMP_OFFSET 20
+
+struct exynos_tmu_data {
+ int irq;
+ int id;
+ unsigned int shift;
+ enum soc_type soc;
+ void __iomem *base;
+ struct clk *clk;
+ struct work_struct irq_work;
+ u8 temp_error1, temp_error2;
+ struct mutex lock;
+ struct thermal_sensor_conf *reg_conf;
+ struct exynos_tmu_platform_data *pdata;
+};
+
+struct exynos_tmu_common {
+ int level[TMU_MAX_SENSOR];
+ int sensor_count;
+};
+static struct exynos_tmu_common tmu_common;
+/*
+ * TMU treats temperature as a mapped temperature code.
+ * The temperature is converted differently depending on the calibration type.
+ */
+static int temp_to_code(struct exynos_tmu_data *data, u8 temp)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ int temp_code;
+
+ if (pdata->cal_mode == HW_MODE)
+ return temp;
+
+ switch (pdata->cal_type) {
+ case TYPE_TWO_POINT_TRIMMING:
+ temp_code = (temp - 25) *
+ (data->temp_error2 - data->temp_error1) /
+ (70 - 25) + data->temp_error1;
+ break;
+ case TYPE_ONE_POINT_TRIMMING:
+ temp_code = temp + data->temp_error1 - 25;
+ break;
+ default:
+ temp_code = temp + TMU_DEF_CODE_TO_TEMP_OFFSET;
+ break;
+ }
+
+ return temp_code;
+}
+
+/*
+ * Calculate a temperature value from a temperature code.
+ * The unit of the temperature is degree Celsius.
+ */
+static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ int temp;
+
+ if (pdata->cal_mode == HW_MODE)
+ return temp_code;
+
+ switch (pdata->cal_type) {
+ case TYPE_TWO_POINT_TRIMMING:
+ temp = (temp_code - data->temp_error1) * (70 - 25) /
+ (data->temp_error2 - data->temp_error1) + 25;
+ break;
+ case TYPE_ONE_POINT_TRIMMING:
+ temp = temp_code - data->temp_error1 + 25;
+ break;
+ default:
+ temp = temp_code - TMU_DEF_CODE_TO_TEMP_OFFSET;
+ break;
+ }
+
+ return temp;
+}
+
+static int exynos_tmu_initialize(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ unsigned int status, con, trim_info;
+ unsigned int rising_threshold = 0, falling_threshold = 0;
+ int ret = 0, threshold_code, i, trigger_levs = 0;
+
+ status = readl(data->base + data->shift + TMU_S0_7_STATUS);
+ status &= 0x1;
+ if (!status)
+ dev_err(&pdev->dev, "Sensor Initial status is busy\n");
+
+ if (pdata->cal_mode == HW_MODE)
+ goto skip_calib_data;
+
+ /* Save trimming info in order to perform calibration */
+ trim_info = readl(data->base + data->shift + TMU_S0_7_TRIM);
+ data->temp_error1 = trim_info & TMU_TEMP_MASK;
+ data->temp_error2 = ((trim_info >> 8) & TMU_TEMP_MASK);
+ if (!data->temp_error1)
+ data->temp_error1 = pdata->efuse_value & TMU_TEMP_MASK;
+ if (!data->temp_error2)
+ data->temp_error2 = (pdata->efuse_value >> 8) & TMU_TEMP_MASK;
+
+skip_calib_data:
+ /* Count trigger levels to be enabled */
+ for (i = 0; i < MAX_THRESHOLD_LEVS; i++)
+ if (pdata->trigger_levels[i])
+ trigger_levs++;
+
+ /* Write temperature code for rising and falling threshold */
+ for (i = 0; (i < trigger_levs && i < TMU_MAX_RISE_LEVEL); i++) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i]);
+ if (threshold_code < 0) {
+ ret = threshold_code;
+ dev_err(&pdev->dev, "Invalid threshold=%d level=%d\n",
+ threshold_code, i);
+ goto out;
+ }
+ rising_threshold |= threshold_code << 8 * i;
+ if (pdata->threshold_falling) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i] -
+ pdata->threshold_falling);
+ if (threshold_code > 0)
+ falling_threshold |=
+ threshold_code << 8 * i;
+ }
+ }
+ writel(rising_threshold,
+ data->base + data->shift + TMU_S0_7_TH0);
+ writel(falling_threshold,
+ data->base + data->shift + TMU_S0_7_TH1);
+
+ /* if 5th threshold limit is also present */
+ if (i == TMU_MAX_RISE_LEVEL) {
+ threshold_code = temp_to_code(data,
+ pdata->trigger_levels[i]);
+ if (threshold_code < 0) {
+ ret = threshold_code;
+ dev_err(&pdev->dev, "Invalid threshold=%d level=%d\n",
+ threshold_code, i);
+ goto out;
+ }
+ rising_threshold = threshold_code << TMU_THRES_RISE4_SHIFT;
+ writel(rising_threshold,
+ data->base + data->shift + TMU_S0_7_TH2);
+ con = readl(data->base + data->shift + TMU_S0_7_CTRL);
+ con |= (1 << TMU_THERM_TRIP_EN_SHIFT);
+ writel(con, data->base + data->shift + TMU_S0_7_CTRL);
+ }
+
+ writel(TMU_CLEAR_RISE_INT | TMU_CLEAR_FALL_INT,
+ data->base + data->shift + TMU_S0_7_IRQ);
+
+ /* clear all PMIN */
+ writel(0, data->base + TMU_PMIN);
+out:
+ return ret;
+}
+
+static void exynos_tmu_control(struct platform_device *pdev, bool on)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ unsigned int con, interrupt_en;
+
+ mutex_lock(&data->lock);
+ con = readl(data->base + data->shift + TMU_S0_7_CTRL);
+ con &= ~(TMU_BUF_VREF_SEL_MASK << TMU_BUF_VREF_SEL_SHIFT |
+ TMU_THERM_TRIP_MODE_MASK << TMU_THERM_TRIP_MODE_SHIFT |
+ TMU_BUF_SLOPE_SEL_MASK << TMU_BUF_SLOPE_SEL_SHIFT |
+ TMU_CALIB_MODE_MASK << TMU_CALIB_MODE_SHIFT |
+ TMU_FILTER_MODE_MASK << TMU_FILTER_MODE_SHIFT |
+ TMU_SENSOR_ENABLE << TMU_SENSOR_EN_SHIFT);
+
+ con |= pdata->reference_voltage << TMU_BUF_VREF_SEL_SHIFT |
+ pdata->gain << TMU_BUF_SLOPE_SEL_SHIFT;
+
+ if (pdata->cal_mode == HW_MODE)
+ con |= pdata->cal_type << TMU_CALIB_MODE_SHIFT;
+
+ con |= pdata->noise_cancel_mode << TMU_THERM_TRIP_MODE_SHIFT;
+
+ if (on) {
+ con |= TMU_SENSOR_ENABLE;
+ interrupt_en =
+ pdata->trigger_enable[3] << 3 |
+ pdata->trigger_enable[2] << 2 |
+ pdata->trigger_enable[1] << 1 |
+ pdata->trigger_enable[0] << 0;
+ if (pdata->threshold_falling)
+ interrupt_en |= interrupt_en << TMU_FALL_IRQEN_SHIFT;
+ } else {
+ interrupt_en = 0; /* Disable all interrupts */
+ }
+ writel(interrupt_en, data->base + data->shift + TMU_S0_7_IRQEN);
+ writel(interrupt_en, data->base + data->shift + TMU_S0_7_EVTEN);
+ writel(con, data->base + data->shift + TMU_S0_7_CTRL);
+
+ mutex_unlock(&data->lock);
+}
+
+static int exynos_tmu_read(struct exynos_tmu_data *data)
+{
+ u8 temp_code;
+ int temp;
+
+ mutex_lock(&data->lock);
Dont you need to enable clocks?
+
+ temp_code = readl(data->base + data->shift + TMU_S0_7_TEMP);
+ temp_code >>= TMU_CURRENT_TEMP_SHIFT;
+ temp_code &= TMU_TEMP_MASK;
+ temp = code_to_temp(data, temp_code);
+
+ mutex_unlock(&data->lock);
+
+ return temp;
+}
+
+#ifdef CONFIG_THERMAL_EMULATION
+static int exynos_tmu_set_emulation(struct exynos_tmu_data *data,
+ unsigned long temp)
+{
+ unsigned int reg;
+
+ if (temp && temp < MCELSIUS)
+ goto out;
+
+ mutex_lock(&data->lock);
+ reg = readl(data->base + data->shift + TMU_S0_7_DEBUG);
+
+ if (temp) {
+ temp /= MCELSIUS;
+ reg &= ~(TMU_TEMP_MASK << TMU_TEMP_EMU_SHIFT);
+ reg |= (temp_to_code(data, temp) << TMU_TEMP_EMU_SHIFT) |
+ TMU_EMUL_ENABLE;
+ } else {
+ reg &= ~TMU_EMUL_ENABLE;
+ }
+
+ writel(reg, data->base + data->shift + TMU_S0_7_DEBUG);
+ mutex_unlock(&data->lock);
+ return 0;
+out:
+ return -EINVAL;
+}
+#endif
+
+static void exynos_tmu_set_cooling(struct exynos_tmu_data *data, int level,
+ unsigned int cur_temp)
+{
+ struct exynos_tmu_platform_data *pdata = data->pdata;
+ bool check_rise, change;
+ unsigned int thres_temp, freq = 0, val;
+ int i, index, max_level = 0;
+
+ /* Get the max level across all sensors except this */
+ for (i = 0; i < tmu_common.sensor_count; i++) {
+ if (i == data->id)
+ continue;
+ if (tmu_common.level[i] > max_level)
+ max_level = tmu_common.level[i];
+ }
+ change = false;
+ if (level < TMU_MAX_RISE_LEVEL) {
+ thres_temp = readl(data->base + data->shift + TMU_S0_7_TH0);
+ thres_temp = (thres_temp >> (level * 8) & TMU_TEMP_MASK);
+ check_rise = true;
+ tmu_common.level[data->id] = level + 1;
+ if (tmu_common.level[data->id] > max_level)
+ change = true;
+ } else {
+ level -= TMU_MAX_RISE_LEVEL;
+ thres_temp = readl(data->base + data->shift + TMU_S0_7_TH1);
+ thres_temp = (thres_temp >> (level * 8) & TMU_TEMP_MASK);
+ check_rise = false;
+ tmu_common.level[data->id] = level;
+ if (tmu_common.level[data->id] >= max_level)
+ change = true;
+ }
+
+ if (change == false)
+ return;
+
+ thres_temp = code_to_temp(data, thres_temp);
+ if (!check_rise)
+ thres_temp += pdata->threshold_falling;
+
+ change = false;
+ /* find this threshold temp in the patform table cooling data */
+ for (i = 0; i < pdata->freq_tab_count; i++) {
+ if (thres_temp != pdata->freq_tab[i].temp_level)
+ continue;
+
+ if (check_rise && cur_temp >= thres_temp) {
+ freq = pdata->freq_tab[i].freq_clip_max;
+ change = true;
+ }
+ if (!check_rise &&
+ (cur_temp <= (thres_temp - pdata->threshold_falling))) {
+ change = true;
+ freq = 0;
+ }
+ }
+
+ /* critical threshold temp */
+ if (thres_temp == pdata->trigger_levels[TMU_MAX_RISE_LEVEL - 1])
+ exynos_report_trigger(data->reg_conf);
+
+ if (change == false)
+ return;
+
+ index = 0;
+
+ if (freq) {
+ index = exynos_get_frequency_level(0, freq);
+ if (index < 0)
+ return;
+ }
+
+ val = readl(data->base + TMU_PMIN);
+ val &= (~(TMU_PMIN_MASK << TMU_PMIN_SHIFT(level)));
+ val |= (index << TMU_PMIN_SHIFT(level));
+ writel(val, data->base + TMU_PMIN);
+}
+
+static void exynos_tmu_work(struct work_struct *work)
+{
+ struct exynos_tmu_data *data = container_of(work,
+ struct exynos_tmu_data, irq_work);
+ int i, cur_temp;
+ unsigned int val_type, val_irq;
+
+ if (!data)
+ goto out;
+
+ val_type = readl(data->base + TMU_IRQ_STATUS);
+
+ /* Find which sensor generated this interrupt */
+ if (!((val_type >> data->id) & 0x1))
+ goto out;
+
+ cur_temp = exynos_tmu_read(data);
+ val_irq = readl(data->base + data->shift + TMU_S0_7_IRQ);
+ for (i = 0; i < (TMU_MAX_RISE_LEVEL + TMU_MAX_FALL_LEVEL); i++) {
+ if (!((val_irq >> i) & 0x1))
+ continue;
+ exynos_tmu_set_cooling(data, i, cur_temp);
+ }
+ /* clear the interrupts */
+ writel(val_irq, data->base + data->shift + TMU_S0_7_IRQ);
+out:
+ enable_irq(data->irq);
+}
+
+static irqreturn_t exynos_tmu_irq(int irq, void *id)
+{
+ struct exynos_tmu_data *data = id;
+
+ disable_irq_nosync(irq);
+ schedule_work(&data->irq_work);
+
+ return IRQ_HANDLED;
+}
+
+static const struct of_device_id exynos_tmu_match[] = {
+ {
+ .compatible = "samsung,exynos5440-tmu",
+ },
+ {},
+};
+MODULE_DEVICE_TABLE(of, exynos_tmu_match);
+
+int exynos_map_dt_data(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct resource res;
+
+ if (!data)
+ return -ENODEV;
+
+ data->id = of_alias_get_id(pdev->dev.of_node, "tmuctrl");
+ if (data->id < 0)
+ data->id = 0;
+
+ data->shift = data->id * 4;
+
+ data->irq = irq_of_parse_and_map(pdev->dev.of_node, 0);
+ if (data->irq <= 0) {
+ dev_err(&pdev->dev, "failed to get IRQ\n");
+ return -ENODEV;
+ }
+
+ if (of_address_to_resource(pdev->dev.of_node, 0, &res)) {
+ dev_err(&pdev->dev, "failed to get Resource\n");
+ return -ENODEV;
+ }
+
+ /* clear the last 16 bytes */
+ res.start &= (~(0xFFFF));
+ data->base = devm_ioremap(&pdev->dev, res.start, resource_size(&res));
+ if (!data->base) {
+ dev_err(&pdev->dev, "Failed to ioremap memory\n");
+ return -ENOMEM;
+ }
+ return 0;
+}
+
+static int exynos_tmu_probe(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data;
+ struct exynos_tmu_platform_data *pdata;
+ struct thermal_sensor_conf *sensor_conf;
+ int ret, i;
+
+ data = devm_kzalloc(&pdev->dev, sizeof(struct exynos_tmu_data),
+ GFP_KERNEL);
+ if (!data) {
+ dev_err(&pdev->dev, "Failed to allocate driver structure\n");
+ return -ENOMEM;
+ }
+
+ pdata = (struct exynos_tmu_platform_data *)
+ platform_get_device_id(pdev)->driver_data;
+ if (!pdata) {
+ dev_err(&pdev->dev, "No platform init data supplied.\n");
+ return -ENODEV;
+ }
+
+ data->pdata = pdata;
+ platform_set_drvdata(pdev, data);
+
+ ret = exynos_map_dt_data(pdev);
+ if (ret)
+ goto unset_data;
+
+ INIT_WORK(&data->irq_work, exynos_tmu_work);
+
+ ret = devm_request_irq(&pdev->dev, data->irq, exynos_tmu_irq,
+ IRQF_TRIGGER_RISING|IRQF_SHARED, dev_name(&pdev->dev), data);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to request irq: %d\n", data->irq);
+ goto unset_data;
+ }
+
+ data->clk = of_clk_get(pdev->dev.of_node, 0);
+ if (IS_ERR(data->clk)) {
+ dev_err(&pdev->dev, "Failed to get tmu clock\n");
+ ret = PTR_ERR(data->clk);
+ goto unset_data;
+ }
+ clk_enable(data->clk);
+
hmmm ok, you want it to be always running, right?
+ mutex_init(&data->lock);
+
+ ret = exynos_tmu_initialize(pdev);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to initialize TMU\n");
+ goto err_clk;
+ }
+
+ exynos_tmu_control(pdev, true);
+
+ /* Allocate a structure to register with the exynos core thermal */
+ sensor_conf = devm_kzalloc(&pdev->dev,
+ sizeof(struct thermal_sensor_conf), GFP_KERNEL);
+ if (!sensor_conf) {
+ dev_err(&pdev->dev, "Failed to allocate registration struct\n");
+ ret = -ENOMEM;
+ goto err_clk;
+ }
+ data->reg_conf = sensor_conf;
+ sprintf(sensor_conf->name, "therm_zone%d", data->id);
+ sensor_conf->read_temperature = (int (*)(void *))exynos_tmu_read;
+#ifdef CONFIG_THERMAL_EMULATION
+ sensor_conf->write_emul_temp =
+ (int (*)(void *, unsigned long))exynos_tmu_set_emulation;
+#endif
Do you really need this ifdef here? Cant you do same as you have done
for 4210?
+ sensor_conf->driver_data = data;
+ sensor_conf->trip_data.trip_count = pdata->trigger_enable[0] +
+ pdata->trigger_enable[1] + pdata->trigger_enable[2] +
+ pdata->trigger_enable[3];
+
+ for (i = 0; i < sensor_conf->trip_data.trip_count; i++)
+ sensor_conf->trip_data.trip_val[i] = pdata->trigger_levels[i];
+
+ sensor_conf->trip_data.trigger_falling = pdata->threshold_falling;
+
+ /* Register the sensor with thermal management interface */
+ ret = exynos_register_thermal(sensor_conf);
+ if (ret) {
+ dev_err(&pdev->dev, "Failed to register thermal interface\n");
+ goto err_clk;
+ }
+ tmu_common.sensor_count++;
+ return 0;
+err_clk:
+ clk_disable(data->clk);
+ clk_put(data->clk);
+unset_data:
+ platform_set_drvdata(pdev, NULL);
+ return ret;
+}
+
+static int exynos_tmu_remove(struct platform_device *pdev)
+{
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+ struct thermal_sensor_conf *sensor_conf = data->reg_conf;
+
+ exynos_tmu_control(pdev, false);
+ clk_disable(data->clk);
+
+ exynos_unregister_thermal(sensor_conf);
+
+ clk_put(data->clk);
+
+ platform_set_drvdata(pdev, NULL);
+
+ return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int exynos_tmu_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+
+ exynos_tmu_control(pdev, false);
+ clk_disable(data->clk);
+
+ return 0;
+}
+
+static int exynos_tmu_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct exynos_tmu_data *data = platform_get_drvdata(pdev);
+
+ clk_enable(data->clk);
+ exynos_tmu_initialize(pdev);
+ exynos_tmu_control(pdev, true);
+
+ return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(exynos_tmu_pm,
+ exynos_tmu_suspend, exynos_tmu_resume);
+#define EXYNOS_TMU_PM (&exynos_tmu_pm)
+#else
+#define EXYNOS_TMU_PM NULL
+#endif
+
+static struct platform_driver exynos_tmu_driver = {
+ .driver = {
+ .name = "exynos5440-tmu",
+ .owner = THIS_MODULE,
+ .pm = EXYNOS_TMU_PM,
+ .of_match_table = exynos_tmu_match,
+ },
+ .probe = exynos_tmu_probe,
+ .remove = exynos_tmu_remove,
+};
+
+module_platform_driver(exynos_tmu_driver);
+
+MODULE_DESCRIPTION("EXYNOS5440 TMU Driver");
+MODULE_AUTHOR("Amit Daniel<amit.daniel@xxxxxxxxxxx>");
+MODULE_LICENSE("GPL");
GPL v2?
+MODULE_ALIAS("platform:exynos5440-tmu");
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
