If gpio based voltage selection for buck 1/2/5 are not used, then the execution
of gpio dvs setup code during probe can be skipped completly.
Cc: MyungJoo Ham <myungjoo.ham@xxxxxxxxxxx>
Cc: Mark Brown <broonie@xxxxxxxxxxxxxxxxxxxxxxxxxxx>
Signed-off-by: Thomas Abraham <thomas.abraham@xxxxxxxxxx>
---
drivers/regulator/max8997.c | 31 ++++++++++++++++++-------------
1 files changed, 18 insertions(+), 13 deletions(-)
diff --git a/drivers/regulator/max8997.c b/drivers/regulator/max8997.c
index cea9ec9..e81a381 100644
--- a/drivers/regulator/max8997.c
+++ b/drivers/regulator/max8997.c
@@ -973,6 +973,10 @@ static int max8997_pmic_probe(struct platform_device *pdev)
memcpy(max8997->buck125_gpios, pdata->buck125_gpios, sizeof(int) * 3);
max8997->ignore_gpiodvs_side_effect = pdata->ignore_gpiodvs_side_effect;
+ if (!pdata->buck1_gpiodvs && !pdata->buck2_gpiodvs &&
+ !pdata->buck5_gpiodvs)
+ goto skip_gpiodvs;
+
for (i = 0; i < 8; i++) {
max8997->buck1_vol[i] = ret =
max8997_get_voltage_proper_val(
@@ -1019,6 +1023,19 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max_buck5, 0x3f);
}
+ /* Initialize all the DVS related BUCK registers */
+ for (i = 0; i < 8; i++) {
+ max8997_update_reg(i2c, MAX8997_REG_BUCK1DVS1 + i,
+ max8997->buck1_vol[i],
+ 0x3f);
+ max8997_update_reg(i2c, MAX8997_REG_BUCK2DVS1 + i,
+ max8997->buck2_vol[i],
+ 0x3f);
+ max8997_update_reg(i2c, MAX8997_REG_BUCK5DVS1 + i,
+ max8997->buck5_vol[i],
+ 0x3f);
+ }
+
/*
* If buck 1, 2, and 5 do not care DVS GPIO settings, ignore them.
* If at least one of them cares, set gpios.
@@ -1060,6 +1077,7 @@ static int max8997_pmic_probe(struct platform_device *pdev)
& 0x1); /* SET3 */
}
+skip_gpiodvs:
/* DVS-GPIO disabled */
max8997_update_reg(i2c, MAX8997_REG_BUCK1CTRL, (pdata->buck1_gpiodvs) ?
(1 << 1) : (0 << 1), 1 << 1);
@@ -1068,19 +1086,6 @@ static int max8997_pmic_probe(struct platform_device *pdev)
max8997_update_reg(i2c, MAX8997_REG_BUCK5CTRL, (pdata->buck5_gpiodvs) ?
(1 << 1) : (0 << 1), 1 << 1);
- /* Initialize all the DVS related BUCK registers */
- for (i = 0; i < 8; i++) {
- max8997_update_reg(i2c, MAX8997_REG_BUCK1DVS1 + i,
- max8997->buck1_vol[i],
- 0x3f);
- max8997_update_reg(i2c, MAX8997_REG_BUCK2DVS1 + i,
- max8997->buck2_vol[i],
- 0x3f);
- max8997_update_reg(i2c, MAX8997_REG_BUCK5DVS1 + i,
- max8997->buck5_vol[i],
- 0x3f);
- }
-
/* Misc Settings */
max8997->ramp_delay = 10; /* set 10mV/us, which is the default */
max8997_write_reg(i2c, MAX8997_REG_BUCKRAMP, (0xf << 4) | 0x9);
--
1.6.6.rc2
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
