This patch adds support for pin configuration using pinctrl subsystem
to the i2c-s3c2410 driver.
Signed-off-by: Tomasz Figa <t.figa@xxxxxxxxxxx>
Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
---
.../devicetree/bindings/i2c/samsung-i2c.txt | 20 ++++++++++++++++----
drivers/i2c/busses/i2c-s3c2410.c | 12 ++++++++----
2 files changed, 24 insertions(+), 8 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
index b6cb5a1..e9611ac 100644
--- a/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
+++ b/Documentation/devicetree/bindings/i2c/samsung-i2c.txt
@@ -13,11 +13,17 @@ Required properties:
- interrupts: interrupt number to the cpu.
- samsung,i2c-sda-delay: Delay (in ns) applied to data line (SDA) edges.
+Required for all cases except "samsung,s3c2440-hdmiphy-i2c":
+ - Samsung GPIO variant (deprecated):
+ - gpios: The order of the gpios should be the following: <SDA, SCL>.
+ The gpio specifier depends on the gpio controller. Required in all
+ cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
+ lines are permanently wired to the respective clienta
+ - Pinctrl variant (preferred, if available):
+ - pinctrl-0: Pin control group to be used for this controller.
+ - pinctrl-names: Should contain only one value - "default".
+
Optional properties:
- - gpios: The order of the gpios should be the following: <SDA, SCL>.
- The gpio specifier depends on the gpio controller. Required in all
- cases except for "samsung,s3c2440-hdmiphy-i2c" whose input/output
- lines are permanently wired to the respective client
- samsung,i2c-slave-addr: Slave address in multi-master enviroment. If not
specified, default value is 0.
- samsung,i2c-max-bus-freq: Desired frequency in Hz of the bus. If not
@@ -31,8 +37,14 @@ Example:
interrupts = <345>;
samsung,i2c-sda-delay = <100>;
samsung,i2c-max-bus-freq = <100000>;
+ /* Samsung GPIO variant begins here */
gpios = <&gpd1 2 0 /* SDA */
&gpd1 3 0 /* SCL */>;
+ /* Samsung GPIO variant ends here */
+ /* Pinctrl variant begins here */
+ pinctrl-0 = <&i2c3_bus>;
+ pinctrl-names = "default";
+ /* Pinctrl variant ends here */
#address-cells = <1>;
#size-cells = <0>;
diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c
index 3e0335f..ae4304b 100644
--- a/drivers/i2c/busses/i2c-s3c2410.c
+++ b/drivers/i2c/busses/i2c-s3c2410.c
@@ -38,6 +38,7 @@
#include <linux/io.h>
#include <linux/of_i2c.h>
#include <linux/of_gpio.h>
+#include <linux/pinctrl/consumer.h>
#include <asm/irq.h>
@@ -83,6 +84,7 @@ struct s3c24xx_i2c {
struct s3c2410_platform_i2c *pdata;
int gpios[2];
+ struct pinctrl *pctrl;
#ifdef CONFIG_CPU_FREQ
struct notifier_block freq_transition;
#endif
@@ -861,9 +863,8 @@ static int s3c24xx_i2c_init(struct s3c24xx_i2c *i2c)
if (pdata->cfg_gpio)
pdata->cfg_gpio(to_platform_device(i2c->dev));
- else
- if (s3c24xx_i2c_parse_dt_gpio(i2c))
- return -EINVAL;
+ else if (IS_ERR(i2c->pctrl) && s3c24xx_i2c_parse_dt_gpio(i2c))
+ return -EINVAL;
/* write slave address */
@@ -1013,6 +1014,8 @@ static int s3c24xx_i2c_probe(struct platform_device *pdev)
i2c->adap.algo_data = i2c;
i2c->adap.dev.parent = &pdev->dev;
+ i2c->pctrl = devm_pinctrl_get_select_default(i2c->dev);
+
/* initialise the i2c controller */
ret = s3c24xx_i2c_init(i2c);
@@ -1112,7 +1115,8 @@ static int s3c24xx_i2c_remove(struct platform_device *pdev)
iounmap(i2c->regs);
release_resource(i2c->ioarea);
- s3c24xx_i2c_dt_gpio_free(i2c);
+ if (pdev->dev.of_node && IS_ERR(i2c->pctrl))
+ s3c24xx_i2c_dt_gpio_free(i2c);
kfree(i2c->ioarea);
return 0;
--
1.8.0
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
