Am Donnerstag, 18. Oktober 2012, 11:36:03 schrieb Seungwon Jeon: > On Thursday, October 18, 2012, Heiko Stübner <heiko@xxxxxxxxx> wrote: > > Hi, > > > > Am Donnerstag, 18. Oktober 2012, 04:04:42 schrieb Jaehoon Chung: > > > Sorry, i didn't check this patch with s3c2416. > > > (i didn't have the s3c2416 board.) > > > If you have a problem, i think good that revert this patch for fixing > > > your problem. Also, i will check and share the result. > > > > After looking a bit more through the code, I don't think the problem is > > 2416- specific but seems to be caused by the gpio card-detect code. > > > > sdhci_s3c_gpio_card_detect_thread calls sdhci_s3c_notify_change which in > > turn runs host->card_tasklet that seems to want to read stuff from the > > card. But this path seems to be missing a runtime-pm wakeup. > > > > I'm not yet sure what to add, especially, as tasklet_finish (called on > > some occasions from tasklet_card) already has a runtime_pm_put call, > > which would be unpaired in this code path. > > > > As there also could be other Samsung platforms affected that use the > > ext-gpio code, it's probably right to revert it for now. Or you see a > > easy fix :-) . > > Hi, > > I think clock is disabled during bus transaction. > I'll send a patch. Could you test it? Sure, I'll test it. Heiko > > > On 10/17/2012 06:15 PM, Heiko Stübner wrote: > > > > Hi, > > > > > > > > Am Freitag, 14. September 2012, 11:08:51 schrieb Chander Kashyap: > > > >> Perform clock disable/enable in runtime suspend/resume. > > > >> > > > >> Signed-off-by: Chander Kashyap <chander.kashyap@xxxxxxxxxx> > > > > > > > > It seems this patch breaks my S3C2416 based machine with 3.7-rc1. I'm > > > > not > > > > > > > > yet sure why, but the only response I get is loop of: > > > > mmc0: Timeout waiting for hardware interrupt. > > > > mmc0: Internal clock never stabilised. > > > > mmc0: Timeout waiting for hardware interrupt. > > > > mmc0: Internal clock never stabilised. > > > > > > > > This only happens on the hsmmc channel using the gpio-based card > > > > detect and even prevents the card from beeing fully detected. The > > > > other hsmmc channel using a permanent emmc seems to be working fine. > > > > > > > > And of course, when I revert this patch everything works fine again. > > > > > > > > I'll investigate further, but it'd be also ok if someone has a fix > > > > for this before me :-) . > > > > > > > > > > > > Heiko > > > > -- > > > > To unsubscribe from this list: send the line "unsubscribe linux-mmc" > > > > in the body of a message to majordomo@xxxxxxxxxxxxxxx > > > > More majordomo info at http://vger.kernel.org/majordomo-info.html > > > > -- > > To unsubscribe from this list: send the line "unsubscribe linux-mmc" in > > the body of a message to majordomo@xxxxxxxxxxxxxxx > > More majordomo info at http://vger.kernel.org/majordomo-info.html -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |