On 08/23/2012 05:15 AM, Thomas Abraham wrote:
> Add a new device tree enabled pinctrl and gpiolib driver for Samsung
> SoC's. This driver provides a common and extensible framework for all
> Samsung SoC's to interface with the pinctrl and gpiolib subsystems. This
> driver supports only device tree based instantiation and hence can be
> used only on those Samsung platforms that have device tree enabled.
>
> This driver is split into two parts: the pinctrl interface and the gpiolib
> interface. The pinctrl interface registers pinctrl devices with the pinctrl
> subsystem and gpiolib interface registers gpio chips with the gpiolib
> subsystem. The information about the pins, pin groups, pin functions and
> gpio chips, which are SoC specific, are parsed from device tree node.
> diff --git a/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/samsung-pinctrl.txt
BTW, this is a very nicely written and complete/precise binding
document. Well done.
> +Samsung GPIO and Pin Mux/Config controller
> +
> +Samsung's ARM based SoC's integrates a GPIO and Pin mux/config hardware
> +controller. It controls the input/output settings on the available pads/pins
> +and also provides ability to multiplex and configure the output of various
> +on-chip controllers onto these pads.
> +
> +Required Properties:
> +- compatible: should be one of the following.
> + - "samsung,pinctrl-exynos4210": for Exynos4210 compatible pin-controller.
> + - "samsung,pinctrl-exynos5250": for Exynos5250 compatible pin-controller.
> +
> +- reg: Base address of the pin controller hardware module and length of
> + the address space it occupies.
> +
> +- interrupts: interrupt specifier for the controller. The format and value of
> + the interrupt specifier depends on the interrupt parent for the controller.
> +
> +- Pin mux/config groups as child nodes: The pin mux (selecting pin function
Direct child nodes of the pin-controller, not a second level?
While that's quite legal, it means that if you need a particular client
module to use 4 pins, 2 of which need one samsung,pin-function value and
2 of which need a different pin-function value, then the client device's
pinctrl-0 property has to have two entries.
i.e. a completely hypothetical example roughly based on yours below:
pinctrl_1: pinctrl@11000000 {
uart0_rxd: uart0-rxd {
samsung,pins = "gpa0-0";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
uart0_txd: uart0-txd {
samsung,pins = "gpa0-1";
samsung,pin-function = <1>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
uart@13800000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_rxd &uart0_txd>;
};
rather than:
pinctrl_1: pinctrl@11000000 {
uart0_opt1: uart0-opt1 {
uart0_rxd: uart0-rxd {
samsung,pins = "gpa0-0";
samsung,pin-function = <2>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
uart0_txd: uart0-txd {
samsung,pins = "gpa0-1";
samsung,pin-function = <1>;
samsung,pin-pud = <0>;
samsung,pin-drv = <0>;
};
};
};
uart@13800000 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_opt1;
};
The latter layout simplifies writing the client nodes, since all the
related settings can be grouped together by whoever writes the pinctrl
node, rather than every client author having to work out all the entries
to include in the list.
That all said, the way you've defined the binding is perfectly
legitimate, and I don't have any kind of issue with it; it's just
something you might want to consider.
Irrespective of whether you choose to keep the binding as-is, or change
it, please consider it:
Acked-by: Stephen Warren <swarren@xxxxxxxxxxxxx>
> + The values specified by these config properties should be dervied from the
s/dervied/derived/
> +External GPIO and Wakeup Interrupts:
> +
> +The controller supports two types of external interrupts over gpio. The first
> +is the external gpio interrupt and second is the external wakeup interrupts.
> +The difference between the two is that the external wakeup interrupts can be
> +used as system wakeup events.
> +
> +A. External GPIO Interrupts: For supporting external gpio interrupts, the
> + properties should be specified in the pin-controller device node.
s/the properties/the following properties/ ?
> +Aliases:
> +
> +All the pin controller nodes should be represented in the aliases node using
> +the following format 'pinctrl{n}' where n is a unique number for the alias.
There /should/ be an alias, or there /may/ be; I'm not sure why
requiring or recommending an alias would be particularly important for
this device?
I've only had time to review the binding document so far.
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
