On 24 July 2012 18:37, Jae hoon Chung <jh80.chung@xxxxxxxxx> wrote:
> Hi Girish,
>
> Right, it be mentioned about the open-drain mode in synopsys spec.
> But if didn't work on other board, there is some problem.
> We can consider the location of set_busmode() .
Sure. Currently i am setting the bus mode after sending the command
during the clock setting. since the bus mode has affect on the cmd
line i will try to move the location of calling bus mode before
setting the clock.
you can just check whether card gets detected by moving the set mode
function just below the switch statement of bus width.
On my board irrespective of the set bus mode location it works fine
>
> Best Regards,
> Jaehoon Chung
>
> 2012/7/24 Girish K S <girish.shivananjappa@xxxxxxxxxx>:
>> On 24 July 2012 17:06, Girish K S <girish.shivananjappa@xxxxxxxxxx> wrote:
>>> On 24 July 2012 16:39, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
>>>> Hi Girish,
>>>>
>>>> Well..just tested on my board.
>>>> this patch didn't work.(eMMC card didn't initialize)
>>>> meaning of ios->bus_mode and synosys's bus_mode is same?
>> Yes it is same. synopsys spec says this is specific to MMC
>> initialization. when the card core sets this mode during
>> initialization. the host has to set this bit
>>>> How did you test this patch?
>>> Tested it on exynos5 board using dt patches of thomas (with some
>>> modification to his patch)
>>>>
>>>> Best Regards,
>>>> Jaehoon Chung
>>>>
>>>> On 07/23/2012 08:16 PM, Girish K S wrote:
>>>>> Synopsis Designware host controller has suppport for open
>>>>> drain mode selection. During the mmc card initialization the
>>>>> host controller can select the open-drain bit to allow the device
>>>>> initialization in the open-drain mode. Once the device enters
>>>>> the standby mode this bit can be reset to enter push-pull mode.
>>>>>
>>>>> Signed-off-by: Girish K S <girish.shivananjappa@xxxxxxxxxx>
>>>>> ---
>>>>> drivers/mmc/host/dw_mmc.c | 14 ++++++++++++++
>>>>> drivers/mmc/host/dw_mmc.h | 1 +
>>>>> 2 files changed, 15 insertions(+), 0 deletions(-)
>>>>>
>>>>> diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
>>>>> index 72dc3cd..da11e5a 100644
>>>>> --- a/drivers/mmc/host/dw_mmc.c
>>>>> +++ b/drivers/mmc/host/dw_mmc.c
>>>>> @@ -773,6 +773,18 @@ static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
>>>>> spin_unlock_bh(&host->lock);
>>>>> }
>>>>>
>>>>> +static void dw_mci_set_busmode(struct dw_mci_slot *slot)
>>>>> +{
>>>>> + struct mmc_ios *ios = &slot->mmc->ios;
>>>>> + u32 reg;
>>>>> +
>>>>> + reg = mci_readl(slot->host, CTRL);
>>>>> + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN)
>>>>> + mci_writel(slot->host, CTRL, reg | SDMMC_CTRL_ENABLE_OD);
>>>>> + else
>>>>> + mci_writel(slot->host, CTRL, reg & ~SDMMC_CTRL_ENABLE_OD);
>>>>> +}
>>>>> +
>>>>> static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
>>>>> {
>>>>> struct dw_mci_slot *slot = mmc_priv(mmc);
>>>>> @@ -818,6 +830,8 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
>>>>> default:
>>>>> break;
>>>>> }
>>>>> +
>>>>> + dw_mci_set_busmode(slot);
>>>>> }
>>>>>
>>>>> static int dw_mci_get_ro(struct mmc_host *mmc)
>>>>> diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
>>>>> index 15c27e1..1a53fb2 100644
>>>>> --- a/drivers/mmc/host/dw_mmc.h
>>>>> +++ b/drivers/mmc/host/dw_mmc.h
>>>>> @@ -67,6 +67,7 @@
>>>>>
>>>>> /* Control register defines */
>>>>> #define SDMMC_CTRL_USE_IDMAC BIT(25)
>>>>> +#define SDMMC_CTRL_ENABLE_OD BIT(24)
>>>>> #define SDMMC_CTRL_CEATA_INT_EN BIT(11)
>>>>> #define SDMMC_CTRL_SEND_AS_CCSD BIT(10)
>>>>> #define SDMMC_CTRL_SEND_CCSD BIT(9)
>>>>>
>>>>
>>>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
