This patch adds support for the HS200 mode on the host side.
Also enables the tuning feature required when the HS200 mode
is selected.
cc: Chris Ball <cjb@xxxxxxxxxx>
Signed-off-by: Girish K S <girish.shivananjappa@xxxxxxxxxx>
---
drivers/mmc/host/sdhci.c | 45 ++++++++++++++++++++++++++++++++++-----------
drivers/mmc/host/sdhci.h | 1 +
include/linux/mmc/host.h | 11 ++++++++++-
include/linux/mmc/sdhci.h | 1 +
4 files changed, 46 insertions(+), 12 deletions(-)
diff --git a/drivers/mmc/host/sdhci.c b/drivers/mmc/host/sdhci.c
index ab6018f..fb17e95 100644
--- a/drivers/mmc/host/sdhci.c
+++ b/drivers/mmc/host/sdhci.c
@@ -49,7 +49,7 @@ static void sdhci_finish_data(struct sdhci_host *);
static void sdhci_send_command(struct sdhci_host *, struct mmc_command *);
static void sdhci_finish_command(struct sdhci_host *);
-static int sdhci_execute_tuning(struct mmc_host *mmc);
+static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode);
static void sdhci_tuning_timer(unsigned long data);
#ifdef CONFIG_PM_RUNTIME
@@ -1016,7 +1016,8 @@ static void sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
flags |= SDHCI_CMD_INDEX;
/* CMD19 is special in that the Data Present Select should be set */
- if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK))
+ if (cmd->data || (cmd->opcode == MMC_SEND_TUNING_BLOCK) ||
+ (cmd->opcode == MMC_SEND_TUNING_BLOCK_HS200))
flags |= SDHCI_CMD_DATA;
sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
@@ -1287,7 +1288,7 @@ static void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
if ((host->flags & SDHCI_NEEDS_RETUNING) &&
!(present_state & (SDHCI_DOING_WRITE | SDHCI_DOING_READ))) {
spin_unlock_irqrestore(&host->lock, flags);
- sdhci_execute_tuning(mmc);
+ sdhci_execute_tuning(mmc, mrq->cmd->opcode);
spin_lock_irqsave(&host->lock, flags);
/* Restore original mmc_request structure */
@@ -1371,7 +1372,8 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
unsigned int clock;
/* In case of UHS-I modes, set High Speed Enable */
- if ((ios->timing == MMC_TIMING_UHS_SDR50) ||
+ if ((ios->timing == MMC_TIMING_MMC_HS200) ||
+ (ios->timing == MMC_TIMING_UHS_SDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR104) ||
(ios->timing == MMC_TIMING_UHS_DDR50) ||
(ios->timing == MMC_TIMING_UHS_SDR25) ||
@@ -1425,7 +1427,9 @@ static void sdhci_do_set_ios(struct sdhci_host *host, struct mmc_ios *ios)
ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
/* Select Bus Speed Mode for host */
ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
- if (ios->timing == MMC_TIMING_UHS_SDR12)
+ if (ios->timing == MMC_TIMING_MMC_HS200)
+ ctrl_2 |= SDHCI_CTRL_HS_SDR200;
+ else if (ios->timing == MMC_TIMING_UHS_SDR12)
ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
else if (ios->timing == MMC_TIMING_UHS_SDR25)
ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
@@ -1673,7 +1677,7 @@ static int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
return err;
}
-static int sdhci_execute_tuning(struct mmc_host *mmc)
+static int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
{
struct sdhci_host *host;
u16 ctrl;
@@ -1694,10 +1698,13 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
* Host Controller needs tuning only in case of SDR104 mode
* and for SDR50 mode when Use Tuning for SDR50 is set in
* Capabilities register.
+ * If the Host Controller supports the HS200 mode then tuning
+ * function has to be executed.
*/
if (((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR104) ||
(((ctrl & SDHCI_CTRL_UHS_MASK) == SDHCI_CTRL_UHS_SDR50) &&
- (host->flags & SDHCI_SDR50_NEEDS_TUNING)))
+ (host->flags & SDHCI_SDR50_NEEDS_TUNING)) ||
+ (host->flags & SDHCI_HS200_NEEDS_TUNING))
ctrl |= SDHCI_CTRL_EXEC_TUNING;
else {
spin_unlock(&host->lock);
@@ -1733,7 +1740,7 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
if (!tuning_loop_counter && !timeout)
break;
- cmd.opcode = MMC_SEND_TUNING_BLOCK;
+ cmd.opcode = opcode;
cmd.arg = 0;
cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
cmd.retries = 0;
@@ -1748,7 +1755,17 @@ static int sdhci_execute_tuning(struct mmc_host *mmc)
* block to the Host Controller. So we set the block size
* to 64 here.
*/
- sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64), SDHCI_BLOCK_SIZE);
+ if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200) {
+ if (mmc->ios.bus_width == MMC_BUS_WIDTH_8)
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 128),
+ SDHCI_BLOCK_SIZE);
+ else if (mmc->ios.bus_width == MMC_BUS_WIDTH_4)
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
+ SDHCI_BLOCK_SIZE);
+ } else {
+ sdhci_writew(host, SDHCI_MAKE_BLKSZ(7, 64),
+ SDHCI_BLOCK_SIZE);
+ }
/*
* The tuning block is sent by the card to the host controller.
@@ -2131,12 +2148,14 @@ static void sdhci_show_adma_error(struct sdhci_host *host) { }
static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
{
+ u32 command;
BUG_ON(intmask == 0);
/* CMD19 generates _only_ Buffer Read Ready interrupt */
if (intmask & SDHCI_INT_DATA_AVAIL) {
- if (SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)) ==
- MMC_SEND_TUNING_BLOCK) {
+ command = SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND));
+ if ((command == MMC_SEND_TUNING_BLOCK) ||
+ (command == MMC_SEND_TUNING_BLOCK_HS200)) {
host->tuning_done = 1;
wake_up(&host->buf_ready_int);
return;
@@ -2741,6 +2760,10 @@ int sdhci_add_host(struct sdhci_host *host)
if (caps[1] & SDHCI_USE_SDR50_TUNING)
host->flags |= SDHCI_SDR50_NEEDS_TUNING;
+ /* Does the host needs tuning for HS200? */
+ if (mmc->caps2 & MMC_CAP2_HS200)
+ host->flags |= SDHCI_HS200_NEEDS_TUNING;
+
/* Driver Type(s) (A, C, D) supported by the host */
if (caps[1] & SDHCI_DRIVER_TYPE_A)
mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
diff --git a/drivers/mmc/host/sdhci.h b/drivers/mmc/host/sdhci.h
index a04d4d0..46fd2ac 100644
--- a/drivers/mmc/host/sdhci.h
+++ b/drivers/mmc/host/sdhci.h
@@ -158,6 +158,7 @@
#define SDHCI_CTRL_UHS_SDR50 0x0002
#define SDHCI_CTRL_UHS_SDR104 0x0003
#define SDHCI_CTRL_UHS_DDR50 0x0004
+#define SDHCI_CTRL_HS_SDR200 0x0005 /*reserved value in SDIO spec */
#define SDHCI_CTRL_VDD_180 0x0008
#define SDHCI_CTRL_DRV_TYPE_MASK 0x0030
#define SDHCI_CTRL_DRV_TYPE_B 0x0000
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 9a03d03..606c8c3 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -56,10 +56,13 @@ struct mmc_ios {
#define MMC_TIMING_UHS_SDR50 3
#define MMC_TIMING_UHS_SDR104 4
#define MMC_TIMING_UHS_DDR50 5
+#define MMC_TIMING_MMC_HS200 6
#define MMC_SDR_MODE 0
#define MMC_1_2V_DDR_MODE 1
#define MMC_1_8V_DDR_MODE 2
+#define MMC_1_2V_SDR_MODE 3
+#define MMC_1_8V_SDR_MODE 4
unsigned char signal_voltage; /* signalling voltage (1.8V or 3.3V) */
@@ -148,7 +151,9 @@ struct mmc_host_ops {
void (*init_card)(struct mmc_host *host, struct mmc_card *card);
int (*start_signal_voltage_switch)(struct mmc_host *host, struct mmc_ios *ios);
- int (*execute_tuning)(struct mmc_host *host);
+
+ /* The tuning command opcode value is different for SD and eMMC cards */
+ int (*execute_tuning)(struct mmc_host *host, u32 opcode);
void (*enable_preset_value)(struct mmc_host *host, bool enable);
int (*select_drive_strength)(unsigned int max_dtr, int host_drv, int card_drv);
void (*hw_reset)(struct mmc_host *host);
@@ -242,6 +247,10 @@ struct mmc_host {
#define MMC_CAP2_CACHE_CTRL (1 << 1) /* Allow cache control */
#define MMC_CAP2_POWEROFF_NOTIFY (1 << 2) /* Notify poweroff supported */
#define MMC_CAP2_NO_MULTI_READ (1 << 3) /* Multiblock reads don't work */
+#define MMC_CAP2_HS200_1_8V_SDR (1 << 4) /* can support */
+#define MMC_CAP2_HS200_1_2V_SDR (1 << 5) /* can support */
+#define MMC_CAP2_HS200 (MMC_CAP2_HS200_1_8V_SDR | \
+ MMC_CAP2_HS200_1_2V_SDR)
mmc_pm_flag_t pm_caps; /* supported pm features */
unsigned int power_notify_type;
diff --git a/include/linux/mmc/sdhci.h b/include/linux/mmc/sdhci.h
index e4b6935..d9a2222 100644
--- a/include/linux/mmc/sdhci.h
+++ b/include/linux/mmc/sdhci.h
@@ -121,6 +121,7 @@ struct sdhci_host {
#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */
#define SDHCI_PV_ENABLED (1<<8) /* Preset value enabled */
#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */
+#define SDHCI_HS200_NEEDS_TUNING (1<<10) /* HS200 needs tuning */
unsigned int version; /* SDHCI spec. version */
--
1.7.1
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
