On 25/07/10 17:41, Vasily Khoruzhick wrote:
> This patch adds gpiolib support for h1940 latch.
> With this patch it's possible to use leds-gpio and uda1380
> drivers (they require gpiolib support for appropriate pins).
> And now it's possible to drop leds-h1940 driver.
I'm reasonably happy with this, any comments from Arnaud?
> Signed-off-by: Vasily Khoruzhick <anarsoul@xxxxxxxxx>
> ---
> arch/arm/mach-s3c2410/h1940-bluetooth.c | 21 ++++--
> arch/arm/mach-s3c2410/include/mach/h1940-latch.h | 57 ++++++------------
> arch/arm/mach-s3c2410/mach-h1940.c | 71 ++++++++++++++++++++--
> arch/arm/plat-s3c24xx/Kconfig | 1 +
> 4 files changed, 99 insertions(+), 51 deletions(-)
>
> diff --git a/arch/arm/mach-s3c2410/h1940-bluetooth.c b/arch/arm/mach-s3c2410/h1940-bluetooth.c
> index 8cdeb14..6b86a72 100644
> --- a/arch/arm/mach-s3c2410/h1940-bluetooth.c
> +++ b/arch/arm/mach-s3c2410/h1940-bluetooth.c
> @@ -30,7 +30,7 @@ static void h1940bt_enable(int on)
> {
> if (on) {
> /* Power on the chip */
> - h1940_latch_control(0, H1940_LATCH_BLUETOOTH_POWER);
> + gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 1);
> /* Reset the chip */
> mdelay(10);
>
> @@ -43,7 +43,7 @@ static void h1940bt_enable(int on)
> mdelay(10);
> gpio_set_value(S3C2410_GPH(1), 0);
> mdelay(10);
> - h1940_latch_control(H1940_LATCH_BLUETOOTH_POWER, 0);
> + gpio_set_value(H1940_LATCH_BLUETOOTH_POWER, 0);
> }
> }
>
> @@ -64,19 +64,26 @@ static int __devinit h1940bt_probe(struct platform_device *pdev)
>
> ret = gpio_request(S3C2410_GPH(1), dev_name(&pdev->dev));
> if (ret) {
> - dev_err(&pdev->dev, "could not get GPH1\n");\
> + dev_err(&pdev->dev, "could not get GPH1\n");
> + return ret;
> + }
> +
> + ret = gpio_request(H1940_LATCH_BLUETOOTH_POWER, dev_name(&pdev->dev));
> + if (ret) {
> + gpio_free(S3C2410_GPH(1));
> + dev_err(&pdev->dev, "could not get BT_POWER\n");
> return ret;
> }
>
> /* Configures BT serial port GPIOs */
> s3c_gpio_cfgpin(S3C2410_GPH(0), S3C2410_GPH0_nCTS0);
> - s3c_gpio_cfgpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
> + s3c_gpio_setpull(S3C2410_GPH(0), S3C_GPIO_PULL_NONE);
> s3c_gpio_cfgpin(S3C2410_GPH(1), S3C2410_GPIO_OUTPUT);
> - s3c_gpio_cfgpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
> + s3c_gpio_setpull(S3C2410_GPH(1), S3C_GPIO_PULL_NONE);
> s3c_gpio_cfgpin(S3C2410_GPH(2), S3C2410_GPH2_TXD0);
> - s3c_gpio_cfgpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
> + s3c_gpio_setpull(S3C2410_GPH(2), S3C_GPIO_PULL_NONE);
> s3c_gpio_cfgpin(S3C2410_GPH(3), S3C2410_GPH3_RXD0);
> - s3c_gpio_cfgpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
> + s3c_gpio_setpull(S3C2410_GPH(3), S3C_GPIO_PULL_NONE);
Is this an error, or have you merged a part of a different patch
into this one?
> rfk = rfkill_alloc(DRV_NAME, &pdev->dev, RFKILL_TYPE_BLUETOOTH,
> diff --git a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
> index d8a8327..4607d5c 100644
> --- a/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
> +++ b/arch/arm/mach-s3c2410/include/mach/h1940-latch.h
> @@ -14,51 +14,30 @@
> #ifndef __ASM_ARCH_H1940_LATCH_H
> #define __ASM_ARCH_H1940_LATCH_H
>
> +#include <mach/gpio.h>
>
> -#ifndef __ASSEMBLY__
> -#define H1940_LATCH ((void __force __iomem *)0xF8000000)
> -#else
> -#define H1940_LATCH 0xF8000000
> -#endif
> -
> -#define H1940_PA_LATCH (S3C2410_CS2)
> +#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + x)
>
> /* SD layer latch */
>
> -#define H1940_LATCH_SDQ1 (1<<16)
> -#define H1940_LATCH_LCD_P1 (1<<17)
> -#define H1940_LATCH_LCD_P2 (1<<18)
> -#define H1940_LATCH_LCD_P3 (1<<19)
> -#define H1940_LATCH_MAX1698_nSHUTDOWN (1<<20) /* LCD backlight */
> -#define H1940_LATCH_LED_RED (1<<21)
> -#define H1940_LATCH_SDQ7 (1<<22)
> -#define H1940_LATCH_USB_DP (1<<23)
> +#define H1940_LATCH_SDQ1 H1940_LATCH_GPIO(0)
> +#define H1940_LATCH_LCD_P1 H1940_LATCH_GPIO(1)
> +#define H1940_LATCH_LCD_P2 H1940_LATCH_GPIO(2)
> +#define H1940_LATCH_LCD_P3 H1940_LATCH_GPIO(3)
> +#define H1940_LATCH_MAX1698_nSHUTDOWN H1940_LATCH_GPIO(4)
> +#define H1940_LATCH_LED_RED H1940_LATCH_GPIO(5)
> +#define H1940_LATCH_SDQ7 H1940_LATCH_GPIO(6)
> +#define H1940_LATCH_USB_DP H1940_LATCH_GPIO(7)
>
> /* CPU layer latch */
>
> -#define H1940_LATCH_UDA_POWER (1<<24)
> -#define H1940_LATCH_AUDIO_POWER (1<<25)
> -#define H1940_LATCH_SM803_ENABLE (1<<26)
> -#define H1940_LATCH_LCD_P4 (1<<27)
> -#define H1940_LATCH_CPUQ5 (1<<28) /* untraced */
> -#define H1940_LATCH_BLUETOOTH_POWER (1<<29) /* active high */
> -#define H1940_LATCH_LED_GREEN (1<<30)
> -#define H1940_LATCH_LED_FLASH (1<<31)
> -
> -/* default settings */
> -
> -#define H1940_LATCH_DEFAULT \
> - H1940_LATCH_LCD_P4 | \
> - H1940_LATCH_SM803_ENABLE | \
> - H1940_LATCH_SDQ1 | \
> - H1940_LATCH_LCD_P1 | \
> - H1940_LATCH_LCD_P2 | \
> - H1940_LATCH_LCD_P3 | \
> - H1940_LATCH_MAX1698_nSHUTDOWN | \
> - H1940_LATCH_CPUQ5
> -
> -/* control functions */
> -
> -extern void h1940_latch_control(unsigned int clear, unsigned int set);
> +#define H1940_LATCH_UDA_POWER H1940_LATCH_GPIO(8)
> +#define H1940_LATCH_AUDIO_POWER H1940_LATCH_GPIO(9)
> +#define H1940_LATCH_SM803_ENABLE H1940_LATCH_GPIO(10)
> +#define H1940_LATCH_LCD_P4 H1940_LATCH_GPIO(11)
> +#define H1940_LATCH_CPUQ5 H1940_LATCH_GPIO(12)
> +#define H1940_LATCH_BLUETOOTH_POWER H1940_LATCH_GPIO(13)
> +#define H1940_LATCH_LED_GREEN H1940_LATCH_GPIO(14)
> +#define H1940_LATCH_LED_FLASH H1940_LATCH_GPIO(15)
>
> #endif /* __ASM_ARCH_H1940_LATCH_H */
> diff --git a/arch/arm/mach-s3c2410/mach-h1940.c b/arch/arm/mach-s3c2410/mach-h1940.c
> index 779b45b..693f467 100644
> --- a/arch/arm/mach-s3c2410/mach-h1940.c
> +++ b/arch/arm/mach-s3c2410/mach-h1940.c
> @@ -42,6 +42,7 @@
> #include <mach/regs-gpio.h>
> #include <mach/gpio-fns.h>
> #include <mach/gpio-nrs.h>
> +#include <mach/gpio.h>
>
> #include <mach/h1940.h>
> #include <mach/h1940-latch.h>
> @@ -58,6 +59,18 @@
> #include <plat/mci.h>
> #include <plat/ts.h>
>
> +#ifndef __ASSEMBLY__
> +#define H1940_LATCH ((void __force __iomem *)0xF8000000)
> +#else
> +#define H1940_LATCH 0xF8000000
> +#endif
> +
> +#define H1940_PA_LATCH (S3C2410_CS2)
> +
> +#define H1940_LATCH_GPIO(x) (S3C_GPIO_END + x)
> +
> +#define H1940_LATCH_BIT(x) (1 << (x + 16 - S3C_GPIO_END))
you probably want an () around the 'x's in the above defines.
> +
> static struct map_desc h1940_iodesc[] __initdata = {
> [0] = {
> .virtual = (unsigned long)H1940_LATCH,
> @@ -99,9 +112,16 @@ static struct s3c2410_uartcfg h1940_uartcfgs[] __initdata = {
>
> /* Board control latch control */
>
> -static unsigned int latch_state = H1940_LATCH_DEFAULT;
> +static unsigned int latch_state = H1940_LATCH_BIT(H1940_LATCH_LCD_P4) |
> + H1940_LATCH_BIT(H1940_LATCH_SM803_ENABLE) |
> + H1940_LATCH_BIT(H1940_LATCH_SDQ1) |
> + H1940_LATCH_BIT(H1940_LATCH_LCD_P1) |
> + H1940_LATCH_BIT(H1940_LATCH_LCD_P2) |
> + H1940_LATCH_BIT(H1940_LATCH_LCD_P3) |
> + H1940_LATCH_BIT(H1940_LATCH_MAX1698_nSHUTDOWN) |
> + H1940_LATCH_BIT(H1940_LATCH_CPUQ5);
>
> -void h1940_latch_control(unsigned int clear, unsigned int set)
> +static void h1940_latch_control(unsigned int clear, unsigned int set)
> {
> unsigned long flags;
>
> @@ -115,7 +135,43 @@ void h1940_latch_control(unsigned int clear, unsigned int set)
> local_irq_restore(flags);
> }
>
> -EXPORT_SYMBOL_GPL(h1940_latch_control);
> +static int h1940_gpiolib_latch_input(struct gpio_chip *chip, unsigned offset)
> +{
> + return -EINVAL;
> +}
> +
> +
> +static void h1940_gpiolib_latch_set(struct gpio_chip *chip,
> + unsigned offset, int value)
> +{
computing the bit seperately to the call to h1940_latch_control
would have made the code easier to read.
> + h1940_latch_control(value ? 0 : (1 << (offset + 16)),
> + value ? (1 << (offset + 16)) : 0);
> +}
> +
> +static int h1940_gpiolib_latch_output(struct gpio_chip *chip,
> + unsigned offset, int value)
> +{
> + h1940_gpiolib_latch_set(chip, offset, value);
> +
> + return 0;
> +}
> +
> +static int h1940_gpiolib_latch_get(struct gpio_chip *chip,
> + unsigned offset)
> +{
> + return (latch_state >> (offset + 16)) & 1;
> +}
> +
> +struct gpio_chip h1940_latch_gpiochip = {
> + .base = H1940_LATCH_GPIO(0),
> + .owner = THIS_MODULE,
> + .label = "H1940_LATCH",
> + .ngpio = 16,
> + .direction_input = h1940_gpiolib_latch_input,
> + .direction_output = h1940_gpiolib_latch_output,
> + .set = h1940_gpiolib_latch_set,
> + .get = h1940_gpiolib_latch_get,
> +};
>
> static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
> {
> @@ -124,10 +180,10 @@ static void h1940_udc_pullup(enum s3c2410_udc_cmd_e cmd)
> switch (cmd)
> {
> case S3C2410_UDC_P_ENABLE :
> - h1940_latch_control(0, H1940_LATCH_USB_DP);
> + gpio_set_value(H1940_LATCH_USB_DP, 1);
> break;
> case S3C2410_UDC_P_DISABLE :
> - h1940_latch_control(H1940_LATCH_USB_DP, 0);
> + gpio_set_value(H1940_LATCH_USB_DP, 0);
> break;
> case S3C2410_UDC_P_RESET :
> break;
> @@ -302,6 +358,8 @@ static void __init h1940_map_io(void)
> memcpy(phys_to_virt(H1940_SUSPEND_RESUMEAT), h1940_pm_return, 1024);
> #endif
> s3c_pm_init();
> +
> + WARN_ON(gpiochip_add(&h1940_latch_gpiochip));
> }
>
> static void __init h1940_init_irq(void)
> @@ -335,6 +393,9 @@ static void __init h1940_init(void)
> gpio_request(S3C2410_GPC(5), "LCD power");
> gpio_request(S3C2410_GPC(6), "LCD power");
>
> + gpio_request(H1940_LATCH_USB_DP, "USB pullup");
> + gpio_direction_output(H1940_LATCH_USB_DP, 0);
> +
> gpio_direction_input(S3C2410_GPC(6));
>
> platform_add_devices(h1940_devices, ARRAY_SIZE(h1940_devices));
> diff --git a/arch/arm/plat-s3c24xx/Kconfig b/arch/arm/plat-s3c24xx/Kconfig
> index 984bf66..5a27b1b 100644
> --- a/arch/arm/plat-s3c24xx/Kconfig
> +++ b/arch/arm/plat-s3c24xx/Kconfig
> @@ -69,6 +69,7 @@ config S3C24XX_GPIO_EXTRA
> int
> default 128 if S3C24XX_GPIO_EXTRA128
> default 64 if S3C24XX_GPIO_EXTRA64
> + default 16 if ARCH_H1940
> default 0
>
> config S3C24XX_GPIO_EXTRA64
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
