Kukjin Kim wrote:
From: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
Adds support for the Samsung PATA controller. This driver is based on the
Libata subsystem and references the earlier patches sent for IDE subsystem.
Signed-off-by: Abhilash Kesavan <a.kesavan@xxxxxxxxxxx>
Signed-off-by: Kukjin Kim <kgene.kim@xxxxxxxxxxx>
[...]
diff --git a/drivers/ata/pata_samsung_cf.c b/drivers/ata/pata_samsung_cf.c
new file mode 100644
index 0000000..fef5515
--- /dev/null
+++ b/drivers/ata/pata_samsung_cf.c
@@ -0,0 +1,608 @@
+/* linux/drivers/ata/pata_samsung_cf.c
File names in the heading comment are discouraged.
[...]
+static unsigned long
+pata_s3c_setup_timing(struct s3c_ide_info *info, struct ata_device *adev)
+{
+ const struct ata_timing *timing;
+ int cycle_time;
+ int t1;
+ int t2;
+ int t2i;
+ ulong piotime;
+
+ cycle_time = (int)(1000000000UL / clk_get_rate(info->clk));
+
+ timing = ata_timing_find_mode(adev->pio_mode);
+ t1 = (timing->setup / cycle_time) & 0xf;
+ t2 = (timing->act8b / cycle_time) & 0xff;
+ t2i = (timing->rec8b / cycle_time) & 0xff;
Why are you still not using ata_timing_compute()?
+
+ piotime = (t2i << 12) | (t2 << 4) | t1;
+
+ return piotime;
+}
+
+static void pata_s3c_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ int mode = adev->pio_mode - XFER_PIO_0;
+ struct s3c_ide_info *info = ap->host->private_data;
+ ulong ata_cfg = readl(info->ide_addr + S3C_ATA_CFG);
+ ulong piotime;
+
+ /* Calculates timing parameters for PIO mode */
+ piotime = pata_s3c_setup_timing(info, adev);
In fact, for 8-bit (command) timing you should program the slowest mode of
the two drives. However, with CF, you probably only have only one drive per
channel...
+
+ /* Enables IORDY if mode requires it */
+ if (ata_pio_need_iordy(adev))
+ ata_cfg |= S3C_ATA_CFG_IORDYEN;
+ else
+ ata_cfg &= ~S3C_ATA_CFG_IORDYEN;
+
+ /* Host controller supports upto PIO4 only */
+ if (mode >= 0 && mode <= 4) {
No need to check -- you won't be passed a mode not specified by your pio_mask.
+ writel(ata_cfg, info->ide_addr + S3C_ATA_CFG);
+ writel(piotime, info->ide_addr + S3C_ATA_PIO_TIME);
+ }
+}
[...]
+/*
+ * pata_s3c_data_xfer - Transfer data by PIO
+ */
+unsigned int pata_s3c_data_xfer(struct ata_device *dev, unsigned char *buf,
+ unsigned int buflen, int rw)
+{
+ struct ata_port *ap = dev->link->ap;
+ struct s3c_ide_info *info = ap->host->private_data;
+ void __iomem *data_addr = ap->ioaddr.data_addr;
+ unsigned int words = buflen >> 1, i;
+ u16 *data_ptr = (u16 *)buf;
+
+ if (rw == READ)
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ *data_ptr = readw(data_addr);
Why not just ignore the result?
+ wait_for_host_ready(info);
+ *data_ptr = readw(info->ide_addr
+ + S3C_ATA_PIO_RDATA);
+ }
+ else
+ for (i = 0; i < words; i++, data_ptr++) {
+ wait_for_host_ready(info);
+ writel(*data_ptr, data_addr);
+ }
+
+ return words << 1;
+}
[...]
+static struct ata_port_operations pata_s3c_port_ops = {
+ .inherits = &ata_sff_port_ops,
+ .sff_check_status = pata_s3c_check_status,
+ .sff_check_altstatus = pata_s3c_check_altstatus,
+ .sff_tf_load = pata_s3c_tf_load,
+ .sff_tf_read = pata_s3c_tf_read,
+ .sff_data_xfer = pata_s3c_data_xfer,
+ .sff_exec_command = pata_s3c_exec_command,
+ .sff_dev_select = pata_s3c_dev_select,
+ .sff_set_devctl = pata_s3c_set_devctl,
I forgot: you also need to override the softreset() method as it accesses
several taskfile registers and ioread8()/iowrite8() won't suffice -- Jeff was
too quick to ack the patch. See ata_bus_softreset(), ata_devchk(), and
ata_sff_wait_after_reset() for the accesses I'm talking about...
[...]
+static int __devinit pata_s3c_probe(struct platform_device *pdev)
+{
+ struct s3c_ide_platdata *pdata = pdev->dev.platform_data;
+ struct device *dev = &pdev->dev;
+ struct s3c_ide_info *info;
+ struct resource *res;
+ struct ata_port *ap;
+ struct ata_host *host;
+ enum s3c_cpu_type cpu_type;
+ int ret;
+
+ cpu_type = platform_get_device_id(pdev)->driver_data;
+
+ info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
+ if (!info) {
+ dev_err(dev, "failed to allocate memory for device data\n");
+ return -ENOMEM;
+ }
+
+ info->irq = platform_get_irq(pdev, 0);
+ if (info->irq < 0) {
+ dev_err(dev, "could not obtain irq number\n");
+ ret = -EINVAL;
+ goto release_device_mem;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (res == NULL) {
+ dev_err(dev, "failed to get mem resource\n");
+ ret = -EINVAL;
+ goto release_device_mem;
+ }
+
+ if (!request_mem_region(res->start, resource_size(res), DRV_NAME)) {
Probably should call devm_request_mem_region() if you're using
devm_ioremap()...
+ dev_err(dev, "error requesting register region\n");
+ return -EBUSY;
+ }
+
+ info->ide_addr = devm_ioremap(dev, res->start, resource_size(res));
+ if (!info->ide_addr) {
+ dev_err(dev, "failed to map IO base address\n");
+ ret = -ENOMEM;
+ goto release_mem;
+ }
+
+ info->clk = clk_get(&pdev->dev, "cfcon");
+ if (IS_ERR(info->clk)) {
+ dev_err(dev, "failed to get access to cf controller clock\n");
+ ret = PTR_ERR(info->clk);
+ info->clk = NULL;
No 'goto' here?
[...]
+stop_clk:
+ clk_disable(info->clk);
Where is clk_put() call?
+release_mem:
+ release_mem_region(res->start, resource_size(res));
+release_device_mem:
+ kfree(info);
Doesn't using devm_kzalloc() guarantee that the memory will be freed up
automatically?
+return ret;
Wrong indentation.
+static struct platform_driver pata_s3c_driver = {
+ .probe = pata_s3c_probe,
2 empty lines -- broken patch?
+ .remove = __devexit_p(pata_s3c_remove),
+ .id_table = pata_s3c_driver_ids,
+ .driver = {
+ .name = DRV_NAME,
+ .owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pata_s3c_pm_ops,
+#endif
+ },
+};
[...]
MBR, Sergei
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
