On 1/15/21 4:29 PM, Bjorn Helgaas wrote: > On Fri, Jan 15, 2021 at 12:20:59PM +0100, Niklas Schnelle wrote: >> On 1/14/21 5:14 PM, Greg Kroah-Hartman wrote: >>> On Thu, Jan 14, 2021 at 04:51:17PM +0100, Niklas Schnelle wrote: >>>> On 1/14/21 4:17 PM, Greg Kroah-Hartman wrote: >>>>> On Thu, Jan 14, 2021 at 04:06:11PM +0100, Niklas Schnelle wrote: >>>>>> On 1/14/21 2:58 PM, Greg Kroah-Hartman wrote: >>>>>>> On Thu, Jan 14, 2021 at 02:44:53PM +0100, Christian Brauner wrote: >>>>>>>> On Thu, Jan 14, 2021 at 02:20:10PM +0100, Niklas Schnelle wrote: >>>>>>>>> On 1/13/21 7:55 PM, Bjorn Helgaas wrote: >>>>>>>>>> On Wed, Jan 13, 2021 at 08:47:58AM +0100, Niklas Schnelle wrote: >>>>>>>>>>> On 1/12/21 10:50 PM, Bjorn Helgaas wrote: >> ... snip ... >> >>> >>>> if (!zpci_global_kset) >>>> return -ENOMEM; >>>> >>>> return sysfs_create_group(&zpci_global_kset->kobj, &zpci_attr_group_global); >>> >>> Huge hint, if in a driver, or bus subsystem, and you call sysfs_*, >>> that's usually a huge clue that you are doing something wrong. >>> >>> Try the above again, with a simple attribute group, and name for it, and >>> it should "just work". >> >> I'm probably missing something but I don't get how this could work >> in this case. If I'm seeing this right the default attribute group >> here is pci_bus_type.bus_groups and that is already set in >> drivers/pci/pci-driver.c so I don't think I should set that. >> >> I did however find bus_create_file() which does work when using the >> path /sys/bus/pci/uid_checking instead. This would work for us if >> Bjorn is okay with that path and the code is really clean and simple >> too. >> >> That said, I think we could also add something like >> bus_create_group(). Then we could use that to also clean up >> drivers/pci/slot.c:pci_slot_init() and get the original path >> /sys/bus/pci/zpci/uid_checking. > > I don't think "uid_checking" is quite the right name. It says > something about the *implementation*, but it doesn't convey what that > *means* to userspace. IIUC this file tells userspace something about > whether a given PCI device always has the same PCI domain/bus/dev/fn > address (or maybe just the same domain?) > > It sounds like this feature could be useful beyond just s390, and > other arches might implement it differently, without the UID concept. > If so, I'm OK with something at the /sys/bus/pci/xxx level as long as > the name is not s390-specific (and "uid" sounds s390-specific). > > I assume it would also help with the udev/systemd end if you could > make this less s390 dependent. > > Bjorn > Hi Bjorn, I've thought about this more and even implemented a proof of concept patch for a global attribute using a pcibios_has_reproducible_addressing() hook. However after implementing it I think as a more general and future proof concept it makes more sense to do this as a per device attribute, maybe as another flag in "stuct pci_dev" named something like "reliable_address". My reasoning behind this can be best be seen with a QEMU example. While I expect that QEMU can easily guarantee that one can always use "0000:01:00.0" for a virtio-pci NIC and thus enp1s0 interface name, the same might be harder to guarantee for a SR-IOV VF passed through with vfio-pci in that same VM and even less so if a thunderbolt controller is passed through and enumeration may depend on daisy chaining. The QEMU example also applies to s390 and maybe others will in the future. I'll send an RFC for a per device attribute but didn't want to let this discussion stand as if we had abandoned the idea and if you would prefer a global attribute I can also send an RFC for that. Besst regards, Niklas
