This patch implement PQAP/AQIC interception in KVM. To implement this we need to add a new structure, vfio_ap_queue,to be able to retrieve the mediated device associated with a queue and specific values needed to register/unregister the interrupt structures: - APQN: to be able to issue the commands and search for queue structures - NIB : to unpin the NIB on clear IRQ - ISC : to unregister with the GIB interface - MATRIX: a pointer to the matrix mediated device - DEV: a pointer to the AP queue device from AP bus. 1) Phase 1, probe and remove from vfio_ap_queue The vfio_ap_queue structures are dynamically allocated when a queue is probed by the ap_vfio_driver. It is linked to the ap_queue device as the driver data. We store the APQN of the ap_queue device inside the vfio_ap_queue. The vfio_ap_queue are free during remove. 2) Phase 2, assignment of vfio_ap_queue to a mediated device When the VFIO device is opened the queues are associated to the mediated device, at the same time the CRYCB is setup. When the device is closed or if a queue is removed the queue is dissociated from the mediated device, as the same time the CRYCB is cleared. Two new functions are used for this: associate/disassociate. 3) Phase 3 intercepting the PQAP/AQIC instruction On interception of the PQAP/AQIC instruction, the interception code makes sure the pqap_hook is initialized and allowed to be called and call it. Otherwise it reports the usual -EOPNOTSUPP return code to let QEMU handle the fault. the pqap callback search for the queue asociated with the APQN stored in the register 0, setting the code to "illegal APQN" if the vfio_ap_queue can not be found. Depending on the "i" bit of the register 1, the pqap callback setup or clear the interruption by calling the host format PQAP/AQIC instruction. When seting up the interruption it uses the NIB and the guest ISC provided by the guest and the host ISC provided by the registration to the GIB code, pin the NIB and also stores ISC and NIB inside the vfio_ap_queue structure. When clearing the interrupt it retrieves the host ISC to unregister with the GIB code and unpin the NIB. There is a QEMU patch which is needed to enable the PQAP/AQIC facility in the guest. Posted in qemu-devel@xxxxxxxxxx as: Message-Id: <1550146494-21085-1-git-send-email-pmorel@xxxxxxxxxxxxx> 4) Phase 4 clean dissociation from the mediated device on remove On removing of the AP device the remove callback is called. To be sure that the guest will not access the queue anymore we clear the APID CRYCB bit. Cleaning the APID, over the APQI, is chosen because the architecture specifies that only the APID can be dynamically changed outside IPL. After this the queue is zeroes, care is taken to correctly wait until the queue is empty. Pierre Morel (9): s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem s390: ap: kvm: setting a hook for PQAP instructions s390: ap: new vfio_ap_queue structure s390: ap: tools to find a queue with a specific APQN s390: ap: tools to associate a queue to a matrix vfio: ap: register IOMMU VFIO notifier s390: ap: implement PAPQ AQIC interception in kernel s390: ap: Cleanup on removing the AP device s390: ap: kvm: add AP Queue Interruption Control facility arch/s390/include/asm/kvm_host.h | 1 + arch/s390/kvm/priv.c | 50 +++++ arch/s390/tools/gen_facilities.c | 1 + drivers/s390/crypto/ap_bus.h | 1 + drivers/s390/crypto/vfio_ap_drv.c | 178 ++++++++++++++++- drivers/s390/crypto/vfio_ap_ops.c | 363 +++++++++++++++++++++++++++++++++- drivers/s390/crypto/vfio_ap_private.h | 12 ++ 7 files changed, 593 insertions(+), 13 deletions(-) -- 2.7.4
