Re: [PATCH v9 12/22] s390: vfio-ap: sysfs interfaces to configure control domains

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 08/22/2018 05:42 AM, Cornelia Huck wrote:
On Wed, 22 Aug 2018 01:18:20 +0200
Halil Pasic <pasic@xxxxxxxxxxxxx> wrote:

On 08/21/2018 07:07 PM, Tony Krowiak wrote:
This convention has been enforced by the kernel since v1. This is also
enforced by both the LPAR as well as in z/VM. The following is from the
PR/SM Planning Guide:

Control Domain
A logical partition's control domains are those cryptographic domains for which remote secure
administration functions can be established and administered from this logical partition. This
logical partition’s control domains must include its usage domains. For each index selected in the
usage domain index list, you must select the same index in the control domain index list
That's interesting.

IMHO this quote is quite a half-full half-empty cup one:
* it mandates the set of usage domains is a subset of the set
of the control domains, but
* it speaks of independent controls, namely about the 'usage domain index'
and the 'control domain index list' and makes the enforcement of the rule
a job of the administrator (instead of codifying it in the controls).
I'm wondering if a configuration with a usage domain that is not also a
control domain is rejected outright? Anybody tried that? :)

That's been tried and is not rejected.


Consequently, I'm going to opt for ensuring this is clearly documented. Based on the fact you've
requested clarification of many points described in this section of the doc, I
think I'll try putting my meager skills as a wordsmith to work to hopefully clarify things.
I'll run it by you when I complete that task to see if I've succeeded:)
I don't think just a doc update will do. Let me explain why.

What describe as "... note that the AQM and ADM masks configured for the
mediated matrix device will be logically OR'd together to create the ADM
stored in the CRYCB referenced from the guest's SIE state description."
is a gotcha at best. The member of struct ap_matrix and the member of the
respective apcb in the crycb are both called 'adm', but ap_matrix.adm is
not an ADM as we know it from the architecture, but rather ~ AQM & ADM.

I feel pretty strongly about this one. If we want to keep the enforcement
in the kernel, I guess, the assign_domain should set the bit corresponding
bit not only in ap_matrix.aqm but also in ap_matrix.adm. When the
ap_matrix is committed into the crycb no further manipulating the masks
should take place.
Would you be fine if the control domain interface stated that it is
used to configure _additional_ control domains and the usage domain
interface stated that it is used to define usage and implicitly also
control domains? (And make the usage domain interface also set the
equivalent bit in the control domain mask.)

I think that is the better way to go and is something Halil recommended
in another post.


I don't feel strongly about whether to enforce this convention about AQM
and ADM in the kernel or not. Frankly, I don't know what is behind the
rule. Since I can't tell if any problems are to be expected if this
convention is violated, I would feel more comfortable if the rule was
accommodated higher in the management stack.
I guess it depends:

- If this is a case of: "Don't configure control domains that are not
   also usage domains. You are likely to go through
   {code,firmware,hardware} paths that are generally not used.",
   configure it in the kernel.
- If this rather is "Everybody is doing that, it's a general
   convention.", configure it higher up in the stack (libvirt?)

I have come to the conclusion that the convention should be enforced
in the sysfs interfaces of the mediated matrix device as follows:

1. All domains assigned as usage domains will also be implicitly
   assigned as control domains.

2. Control domains that are not usage domains may be assigned via
   the assign_control_domain interface.

My reason is to maintain consistency across platforms, because:

1. The architecture doc states that control domains are a superset
   of the usage domains.

2. The HMC interface for assigning domains to the LPAR enforces
   the convention.

3. The PR/SM documentation states the same.








[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [Kernel Development]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Info]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Linux Media]     [Device Mapper]

  Powered by Linux