On Mon, Jul 18, 2011 at 04:00:41PM +0200, Michael Holzheu wrote: > Hello Vivek, > > On Mon, 2011-07-18 at 08:31 -0400, Vivek Goyal wrote: > > On Fri, Jul 15, 2011 at 05:43:23PM +0200, Michael Holzheu wrote: > > > > Or in first step we can keep it even simpler. We can spin in infinite > > > > loop > > > > > > Looping is probably not a good option in a hypervisor environment like > > > we have it on s390. At least we should load a disabled wait PSW. > > > > What is "disabled wait PSW"? > > This is a PSW where interrupts are disabled and the wait bit is on. This > ensures that the virtual CPU is stopped and does not consume any CPU > time. > > > > > In your case I think you shall have to do little more so that second > > > > kernel also seems some of the lower memory areas so that later swapping > > > > of kernel can be done. > > > > > > After the swap the ELF header is contained in the same memory than the > > > kdump kernel. When the kdump kernel starts, the ELF header has to be > > > saved from being overwritten (as kernel and ramdisk). I get the address > > > from the "elfcorehdr=" kernel parameter. How will I get the size? > > > > By parsing the ELF header. It will give you information about how many > > program headers and notes are there, their sizes and locations etc. > > The only thing we need is the size of the preallocated header that is in > kdump memory. All other architectures seem to pass this information > somehow with different mechanisms to the kdump kernel (memmap kernel > parameter, boot parameters, etc.). Why should *we* parse the ELF header? ELF headers and memmap parameters are communicating two different pieces of information to second kenrel. - memap tells what memory second kernel can use to boot. - ELF headers tell what memory areas first kernel was using and using that information how to construct ELF headers for /proc/vmcore interface in second kernel. On x86, ELF headers also communicate where the saved cpu state is for the first kernel. Arch independent code in kdump kenrel (fs/proc/vmcore.c) is parsing those ELF headers to export /proc/vmcore. So if you set up the headers right you get that arch independent code for free without any changes to generic code. *Why should you not try to use what is avaialble already* > > > When kexec-tools loads ELF headers, it knows what's the total size of > > ELF headers and it removes that chunk of memory from the memory map > > passed to second kernel with memmap= options. IOW, some memory out > > of reserved region is not usable by second kernel because we have > > stored information in that memory. Kdump kernel maps that memory and > > gets to read the ELF headers. > > > > So you shall have to do something similar where you need to tell second > > kernel what memory areas it can use for boot and remove ELF header > > memory area from the map. > > So if we do that, why should we parse the ELF header? To know three things. - Memory areas being used by first kernel. - Cpu states at the time of crash of first kernel. - Some config options exported by first kernel with the help of ELF notes. fs/proc/vmcore.c already does it for you. You just need to make sure that you tell it following. - Where to find the headers in memory (elfcorehdr=) - A way to map that memory and access contents. - Make sure these headers are not overwritten by newly booted kernel. [..] > > It is possible. Even in x86, we prepare a block of information, one > > 4K page and fill lots of x86 boot protocol information. > > > > Look at. > > > > kexec-tools/include/x86/x86-linux.h > > kexec-tools/kexec/arch/i386/x86-linux-setup.c > > > > Above header information contains information about e820 memory map also > > and we fill that map info for normal kexec (fastboot, not kdump) also and > > that's how second kernel comes to know about memory map of system. > > > > I think one could possibly truncate the same map for kdump kernel to > > tell second kernel about the memory to use. But IIRC, original memory > > map is also used to determine max_pfn present in first kernel so that > > in second kernel we don't try to map a memory beyond that and access > > it, etc. Hence it was decided to leave it that way and pass the memory > > map for second kernel on command line. > > > > So its possible that IA64 is doing preparing boot protocal specific > > block and passing all the releavant information in that block instead > > of making use of commnad line. > > Just to come back to your initial argumentation against our meminfo > approach: It looks like that there are already other mechanisms besides > of ELF-header and kernel parameters to pass information to the kdump > kernel. Where is the conceptional difference to our meminfo interface? That's well defined boot-loader and kernel protocol to on x86. kexec-tools is just another boot loader and it uses that block to fill the information a normal boot loader will do. So if you have s390 specific boot loader/kernel protocol and if you extend that, I think that should still be fine. Just keep the code in kexec-tools for filling up the information which s390 specific code can parse. In that case we should not require any generic changes to either kexec-tools or kernel code. All the protocol specific details should be well hidden in arch specific code. Thanks Vivek -- To unsubscribe from this list: send the line "unsubscribe linux-s390" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html