TPS6594 is a Power Management IC which provides regulators and others features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and PFSM (Pre-configurable Finite State Machine). The SoC and the PMIC can communicate through the I2C or SPI interfaces. TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives. This series adds support to TI TPS6594 PMIC and its derivatives. This should be applied on top of other patch series: - https://lore.kernel.org/all/20230406075622.8990-1-jpanis@xxxxxxxxxxxx/ For core MFD driver The features implemented in this series are: - RTC (child device) - Pinmux/GPIO (child device) - Regulator (child device) RTC description: The TPS6594 family has an RTC built-in, except for LP8764. It provides time and an alarm. Pinmux/GPIO: TPS6594 family has 11 GPIOs. Those GPIO can also serve different functions such as I2C or SPI interface, watchdog disable functions. The driver provides both pinmuxing for the functions and GPIO capability. Regulator: TPS6594/TPS6593: 5 BUCKs and 4LDOs LP8764: 4 BUCKs and no LDO Bucks can be used in multipahse mode. Changes since v1: https://lore.kernel.org/all/20230224133129.887203-1-eblanc@xxxxxxxxxxxx/ Rtc: - Removed struct tps6594_rtc. - Removed some dev_err messages. - Removed some comments. - Remove some whitespaces in comments and error messages. - Check if RTC is running before reading a timestamp in read_rtc. - Stop RTC at the end of probe to wait for a timestamp to be set. - Add default MFD_TPS6594 to Kconfig. Pinctrl: - Removed #define DEBUG. - Add default MFD_TPS6594 to Kconfig. - Fix typo and reword help message of Kconfig. Regulators: Further to Mark Brown review: - File header whole block C++ style. - Configuring modes not supported: omit all mode operations - Log the error before notifying. - Request the interrupts while registering the regulators (then remove the lookup function). Further to Matti review: - Postponed: devm_regulator_irq_helper() and regulator_irq_map_event_simple() can probably be used but code. refactoring is not so trivial. This can be done later as an enhancement after this patch list is merged. Buck Multi phase management: - Multiphase property can take an array when 2 multi phase buck, buck12 and buck34. - Configuration multi phase buck34 without multiphase buck12 is not supported (when only one multiphase, must be buck12). Not clear from the spec but confirmed by TI. - Supported multiphase conficurations: buck12, buck123, buck1234, buck12 + buck34. - All interrupts are attached to the multiphase buck (ie: for regulator buck12, buck1 & buck2 interrupts are registered). Changes since v2: https://lore.kernel.org/all/20230328091448.648452-1-eblanc@xxxxxxxxxxxx/ Rtc: - Add logic to avoid reinitializing a working clock. - Fix some multiline comments format. Regulators: Further to Mark Brown review: - Log the error before notifying. - Request the interrupts while registering the regulators. Further to Krzysztof Kozlowski: https://lore.kernel.org/all/75f0a18d-aed9-8610-2925-4e604b4b0241@xxxxxxxxxxxx/ - Remove ti, multi-phase-id property which is redundant with buck dts naming rules. Esteban Blanc (2): rtc: tps6594: add driver for TPS6594 PMIC RTC pinctrl: tps6594: add for TPS6594 PMIC Jerome Neanne (1): regulator: tps6594-regulator: Add driver for TI TPS6594 regulators drivers/pinctrl/Kconfig | 10 + drivers/pinctrl/Makefile | 1 + drivers/pinctrl/pinctrl-tps6594.c | 365 +++++++++++++++ drivers/regulator/Kconfig | 13 + drivers/regulator/Makefile | 1 + drivers/regulator/tps6594-regulator.c | 620 ++++++++++++++++++++++++++ drivers/rtc/Kconfig | 9 + drivers/rtc/Makefile | 1 + drivers/rtc/rtc-tps6594.c | 473 ++++++++++++++++++++ 9 files changed, 1493 insertions(+) create mode 100644 drivers/pinctrl/pinctrl-tps6594.c create mode 100644 drivers/regulator/tps6594-regulator.c create mode 100644 drivers/rtc/rtc-tps6594.c -- 2.39.2
