From: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
The PCF2127 and PCF2129 have one output interrupt pin. The PCF2131 has
two, named INT_A and INT_B. The hardware support that any interrupt
source can be routed to either one or both of them.
Force all interrupt sources to go to the INT A pin.
Support to route any interrupt source to INT A/B pins is not supported
by this driver at the moment.
Signed-off-by: Hugo Villeneuve <hvilleneuve@xxxxxxxxxxxx>
---
drivers/rtc/rtc-pcf2127.c | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/drivers/rtc/rtc-pcf2127.c b/drivers/rtc/rtc-pcf2127.c
index 4148e135f935..68af4d0438b8 100644
--- a/drivers/rtc/rtc-pcf2127.c
+++ b/drivers/rtc/rtc-pcf2127.c
@@ -191,6 +191,7 @@ struct pcf21xx_config {
int max_register;
unsigned int has_nvmem:1;
unsigned int has_bit_wd_ctl_cd0:1;
+ unsigned int has_int_a_b:1; /* PCF2131 supports two interrupt outputs. */
u8 regs_td_base; /* Time/data base registers. */
u8 regs_alarm_base; /* Alarm function base registers. */
u8 reg_wd_ctl; /* Watchdog control register. */
@@ -879,6 +880,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
.max_register = 0x1d,
.has_nvmem = 1,
.has_bit_wd_ctl_cd0 = 1,
+ .has_int_a_b = 0,
.regs_td_base = PCF2127_REG_TIME_DATE_BASE,
.regs_alarm_base = PCF2127_REG_ALARM_BASE,
.reg_wd_ctl = PCF2127_REG_WD_CTL,
@@ -902,6 +904,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
.max_register = 0x19,
.has_nvmem = 0,
.has_bit_wd_ctl_cd0 = 0,
+ .has_int_a_b = 0,
.regs_td_base = PCF2127_REG_TIME_DATE_BASE,
.regs_alarm_base = PCF2127_REG_ALARM_BASE,
.reg_wd_ctl = PCF2127_REG_WD_CTL,
@@ -925,6 +928,7 @@ static struct pcf21xx_config pcf21xx_cfg[] = {
.max_register = 0x36,
.has_nvmem = 0,
.has_bit_wd_ctl_cd0 = 0,
+ .has_int_a_b = 1,
.regs_td_base = PCF2131_REG_TIME_DATE_BASE,
.regs_alarm_base = PCF2131_REG_ALARM_BASE,
.reg_wd_ctl = PCF2131_REG_WD_CTL,
@@ -1017,6 +1021,28 @@ static int pcf2127_enable_ts(struct device *dev, int ts_id)
return ret;
}
+/* Route all interrupt sources to INT A pin. */
+static int pcf2127_configure_interrupt_pins(struct device *dev)
+{
+ struct pcf2127 *pcf2127 = dev_get_drvdata(dev);
+ int ret;
+
+ /* Mask bits need to be cleared to enable corresponding
+ * interrupt source.
+ */
+ ret = regmap_write(pcf2127->regmap,
+ PCF2131_REG_INT_A_MASK1, 0);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(pcf2127->regmap,
+ PCF2131_REG_INT_A_MASK2, 0);
+ if (ret)
+ return ret;
+
+ return ret;
+}
+
static int pcf2127_probe(struct device *dev, struct regmap *regmap,
int alarm_irq, const char *name, const struct pcf21xx_config *config)
{
@@ -1076,6 +1102,15 @@ static int pcf2127_probe(struct device *dev, struct regmap *regmap,
set_bit(RTC_FEATURE_ALARM, pcf2127->rtc->features);
}
+ if (pcf2127->cfg->has_int_a_b) {
+ /* Configure int A/B pins, independently of alarm_irq. */
+ ret = pcf2127_configure_interrupt_pins(dev);
+ if (ret) {
+ dev_err(dev, "failed to configure interrupt pins\n");
+ return ret;
+ }
+ }
+
if (pcf2127->cfg->has_nvmem) {
struct nvmem_config nvmem_cfg = {
.priv = pcf2127,
--
2.30.2
