Our chosen byte swapping, which is what firmware already uses, is to
do readl/writel by normal lw/sw intructions (data invariance). This
also means we need to mangle addresses for u8 and u16 accesses. The
mangling for 16bit has been done aready, but 8bit one was missing.
Correcting this causes different addresses for accesses to the
SuperIO and local bus of the IOC3 chip. This is fixed by changing
byte order in ioc3 and m48rtc_rtc structs.
Acked-by: Alexandre Belloni <alexandre.belloni@xxxxxxxxxxx>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@xxxxxxx>
---
arch/mips/include/asm/mach-ip27/mangle-port.h | 4 +-
arch/mips/include/asm/sn/ioc3.h | 198 +++++++++++++-------------
arch/mips/sgi-ip27/ip27-console.c | 5 +-
drivers/rtc/rtc-m48t35.c | 11 ++
drivers/tty/serial/8250/8250_ioc3.c | 4 +-
5 files changed, 115 insertions(+), 107 deletions(-)
diff --git a/arch/mips/include/asm/mach-ip27/mangle-port.h b/arch/mips/include/asm/mach-ip27/mangle-port.h
index f6e4912ea062..27c56efa519f 100644
--- a/arch/mips/include/asm/mach-ip27/mangle-port.h
+++ b/arch/mips/include/asm/mach-ip27/mangle-port.h
@@ -8,7 +8,7 @@
#ifndef __ASM_MACH_IP27_MANGLE_PORT_H
#define __ASM_MACH_IP27_MANGLE_PORT_H
-#define __swizzle_addr_b(port) (port)
+#define __swizzle_addr_b(port) ((port) ^ 3)
#define __swizzle_addr_w(port) ((port) ^ 2)
#define __swizzle_addr_l(port) (port)
#define __swizzle_addr_q(port) (port)
@@ -20,6 +20,6 @@
# define ioswabl(a, x) (x)
# define __mem_ioswabl(a, x) cpu_to_le32(x)
# define ioswabq(a, x) (x)
-# define __mem_ioswabq(a, x) cpu_to_le32(x)
+# define __mem_ioswabq(a, x) cpu_to_le64(x)
#endif /* __ASM_MACH_IP27_MANGLE_PORT_H */
diff --git a/arch/mips/include/asm/sn/ioc3.h b/arch/mips/include/asm/sn/ioc3.h
index 89938fdce8ef..ac6d7e6e31e0 100644
--- a/arch/mips/include/asm/sn/ioc3.h
+++ b/arch/mips/include/asm/sn/ioc3.h
@@ -10,35 +10,35 @@
/* serial port register map */
struct ioc3_serialregs {
- uint32_t sscr;
- uint32_t stpir;
- uint32_t stcir;
- uint32_t srpir;
- uint32_t srcir;
- uint32_t srtr;
- uint32_t shadow;
+ u32 sscr;
+ u32 stpir;
+ u32 stcir;
+ u32 srpir;
+ u32 srcir;
+ u32 srtr;
+ u32 shadow;
};
/* SUPERIO uart register map */
struct ioc3_uartregs {
+ u8 iu_lcr;
union {
- char rbr; /* read only, DLAB == 0 */
- char thr; /* write only, DLAB == 0 */
- char dll; /* DLAB == 1 */
- } u1;
+ u8 iir; /* read only */
+ u8 fcr; /* write only */
+ };
union {
- char ier; /* DLAB == 0 */
- char dlm; /* DLAB == 1 */
- } u2;
+ u8 ier; /* DLAB == 0 */
+ u8 dlm; /* DLAB == 1 */
+ };
union {
- char iir; /* read only */
- char fcr; /* write only */
- } u3;
- char iu_lcr;
- char iu_mcr;
- char iu_lsr;
- char iu_msr;
- char iu_scr;
+ u8 rbr; /* read only, DLAB == 0 */
+ u8 thr; /* write only, DLAB == 0 */
+ u8 dll; /* DLAB == 1 */
+ } u1;
+ u8 iu_scr;
+ u8 iu_msr;
+ u8 iu_lsr;
+ u8 iu_mcr;
};
#define iu_rbr u1.rbr
@@ -50,122 +50,122 @@ struct ioc3_uartregs {
#define iu_fcr u3.fcr
struct ioc3_sioregs {
- char fill[0x141]; /* starts at 0x141 */
+ u8 fill[0x141]; /* starts at 0x141 */
- char uartc;
- char kbdcg;
+ u8 kbdcg;
+ u8 uartc;
- char fill0[0x150 - 0x142 - 1];
+ u8 fill0[0x151 - 0x142 - 1];
- char pp_data;
- char pp_dsr;
- char pp_dcr;
+ u8 pp_dcr;
+ u8 pp_dsr;
+ u8 pp_data;
- char fill1[0x158 - 0x152 - 1];
+ u8 fill1[0x159 - 0x153 - 1];
- char pp_fifa;
- char pp_cfgb;
- char pp_ecr;
+ u8 pp_ecr;
+ u8 pp_cfgb;
+ u8 pp_fifa;
- char fill2[0x168 - 0x15a - 1];
+ u8 fill2[0x16a - 0x15b - 1];
- char rtcad;
- char rtcdat;
+ u8 rtcdat;
+ u8 rtcad;
- char fill3[0x170 - 0x169 - 1];
+ u8 fill3[0x170 - 0x16b - 1];
struct ioc3_uartregs uartb; /* 0x20170 */
struct ioc3_uartregs uarta; /* 0x20178 */
};
struct ioc3_ethregs {
- uint32_t emcr; /* 0x000f0 */
- uint32_t eisr; /* 0x000f4 */
- uint32_t eier; /* 0x000f8 */
- uint32_t ercsr; /* 0x000fc */
- uint32_t erbr_h; /* 0x00100 */
- uint32_t erbr_l; /* 0x00104 */
- uint32_t erbar; /* 0x00108 */
- uint32_t ercir; /* 0x0010c */
- uint32_t erpir; /* 0x00110 */
- uint32_t ertr; /* 0x00114 */
- uint32_t etcsr; /* 0x00118 */
- uint32_t ersr; /* 0x0011c */
- uint32_t etcdc; /* 0x00120 */
- uint32_t ebir; /* 0x00124 */
- uint32_t etbr_h; /* 0x00128 */
- uint32_t etbr_l; /* 0x0012c */
- uint32_t etcir; /* 0x00130 */
- uint32_t etpir; /* 0x00134 */
- uint32_t emar_h; /* 0x00138 */
- uint32_t emar_l; /* 0x0013c */
- uint32_t ehar_h; /* 0x00140 */
- uint32_t ehar_l; /* 0x00144 */
- uint32_t micr; /* 0x00148 */
- uint32_t midr_r; /* 0x0014c */
- uint32_t midr_w; /* 0x00150 */
+ u32 emcr; /* 0x000f0 */
+ u32 eisr; /* 0x000f4 */
+ u32 eier; /* 0x000f8 */
+ u32 ercsr; /* 0x000fc */
+ u32 erbr_h; /* 0x00100 */
+ u32 erbr_l; /* 0x00104 */
+ u32 erbar; /* 0x00108 */
+ u32 ercir; /* 0x0010c */
+ u32 erpir; /* 0x00110 */
+ u32 ertr; /* 0x00114 */
+ u32 etcsr; /* 0x00118 */
+ u32 ersr; /* 0x0011c */
+ u32 etcdc; /* 0x00120 */
+ u32 ebir; /* 0x00124 */
+ u32 etbr_h; /* 0x00128 */
+ u32 etbr_l; /* 0x0012c */
+ u32 etcir; /* 0x00130 */
+ u32 etpir; /* 0x00134 */
+ u32 emar_h; /* 0x00138 */
+ u32 emar_l; /* 0x0013c */
+ u32 ehar_h; /* 0x00140 */
+ u32 ehar_l; /* 0x00144 */
+ u32 micr; /* 0x00148 */
+ u32 midr_r; /* 0x0014c */
+ u32 midr_w; /* 0x00150 */
};
struct ioc3_serioregs {
- uint32_t km_csr; /* 0x0009c */
- uint32_t k_rd; /* 0x000a0 */
- uint32_t m_rd; /* 0x000a4 */
- uint32_t k_wd; /* 0x000a8 */
- uint32_t m_wd; /* 0x000ac */
+ u32 km_csr; /* 0x0009c */
+ u32 k_rd; /* 0x000a0 */
+ u32 m_rd; /* 0x000a4 */
+ u32 k_wd; /* 0x000a8 */
+ u32 m_wd; /* 0x000ac */
};
/* Register layout of IOC3 in configuration space. */
struct ioc3 {
/* PCI Config Space registers */
- uint32_t pci_id; /* 0x00000 */
- uint32_t pci_scr; /* 0x00004 */
- uint32_t pci_rev; /* 0x00008 */
- uint32_t pci_lat; /* 0x0000c */
- uint32_t pci_addr; /* 0x00010 */
- uint32_t pci_err_addr_l; /* 0x00014 */
- uint32_t pci_err_addr_h; /* 0x00018 */
-
- uint32_t sio_ir; /* 0x0001c */
- uint32_t sio_ies; /* 0x00020 */
- uint32_t sio_iec; /* 0x00024 */
- uint32_t sio_cr; /* 0x00028 */
- uint32_t int_out; /* 0x0002c */
- uint32_t mcr; /* 0x00030 */
+ u32 pci_id; /* 0x00000 */
+ u32 pci_scr; /* 0x00004 */
+ u32 pci_rev; /* 0x00008 */
+ u32 pci_lat; /* 0x0000c */
+ u32 pci_addr; /* 0x00010 */
+ u32 pci_err_addr_l; /* 0x00014 */
+ u32 pci_err_addr_h; /* 0x00018 */
+
+ u32 sio_ir; /* 0x0001c */
+ u32 sio_ies; /* 0x00020 */
+ u32 sio_iec; /* 0x00024 */
+ u32 sio_cr; /* 0x00028 */
+ u32 int_out; /* 0x0002c */
+ u32 mcr; /* 0x00030 */
/* General Purpose I/O registers */
- uint32_t gpcr_s; /* 0x00034 */
- uint32_t gpcr_c; /* 0x00038 */
- uint32_t gpdr; /* 0x0003c */
- uint32_t gppr[16]; /* 0x00040 */
+ u32 gpcr_s; /* 0x00034 */
+ u32 gpcr_c; /* 0x00038 */
+ u32 gpdr; /* 0x0003c */
+ u32 gppr[16]; /* 0x00040 */
/* Parallel Port Registers */
- uint32_t ppbr_h_a; /* 0x00080 */
- uint32_t ppbr_l_a; /* 0x00084 */
- uint32_t ppcr_a; /* 0x00088 */
- uint32_t ppcr; /* 0x0008c */
- uint32_t ppbr_h_b; /* 0x00090 */
- uint32_t ppbr_l_b; /* 0x00094 */
- uint32_t ppcr_b; /* 0x00098 */
+ u32 ppbr_h_a; /* 0x00080 */
+ u32 ppbr_l_a; /* 0x00084 */
+ u32 ppcr_a; /* 0x00088 */
+ u32 ppcr; /* 0x0008c */
+ u32 ppbr_h_b; /* 0x00090 */
+ u32 ppbr_l_b; /* 0x00094 */
+ u32 ppcr_b; /* 0x00098 */
/* Keyboard and Mouse Registers */
struct ioc3_serioregs serio;
/* Serial Port Registers */
- uint32_t sbbr_h; /* 0x000b0 */
- uint32_t sbbr_l; /* 0x000b4 */
+ u32 sbbr_h; /* 0x000b0 */
+ u32 sbbr_l; /* 0x000b4 */
struct ioc3_serialregs port_a;
struct ioc3_serialregs port_b;
/* Ethernet Registers */
struct ioc3_ethregs eth;
- uint32_t pad1[(0x20000 - 0x00154) / 4];
+ u32 pad1[(0x20000 - 0x00154) / 4];
/* SuperIO Registers XXX */
struct ioc3_sioregs sregs; /* 0x20000 */
- uint32_t pad2[(0x40000 - 0x20180) / 4];
+ u32 pad2[(0x40000 - 0x20180) / 4];
/* SSRAM Diagnostic Access */
- uint32_t ssram[(0x80000 - 0x40000) / 4];
+ u32 ssram[(0x80000 - 0x40000) / 4];
/* Bytebus device offsets
0x80000 - Access to the generic devices selected with DEV0
@@ -598,10 +598,6 @@ struct ioc3_etxd {
#define MIDR_DATA_MASK 0x0000ffff
-#if defined(CONFIG_SGI_IP27) || defined(CONFIG_SGI_IP30)
-extern int bridge_alloc_irq(struct pci_dev *dev);
-#endif
-
/* subsystem IDs supplied by card detection in pci-xtalk-bridge */
#define IOC3_SUBSYS_IP27_BASEIO6G 0xc300
#define IOC3_SUBSYS_IP27_MIO 0xc301
diff --git a/arch/mips/sgi-ip27/ip27-console.c b/arch/mips/sgi-ip27/ip27-console.c
index 6bdb48d41276..5886bee89d06 100644
--- a/arch/mips/sgi-ip27/ip27-console.c
+++ b/arch/mips/sgi-ip27/ip27-console.c
@@ -35,6 +35,7 @@ void prom_putchar(char c)
{
struct ioc3_uartregs *uart = console_uart();
- while ((uart->iu_lsr & 0x20) == 0);
- uart->iu_thr = c;
+ while ((readb(&uart->iu_lsr) & 0x20) == 0)
+ ;
+ writeb(c, &uart->iu_thr);
}
diff --git a/drivers/rtc/rtc-m48t35.c b/drivers/rtc/rtc-m48t35.c
index d3a75d447fce..e8194f1f01a8 100644
--- a/drivers/rtc/rtc-m48t35.c
+++ b/drivers/rtc/rtc-m48t35.c
@@ -20,6 +20,16 @@
struct m48t35_rtc {
u8 pad[0x7ff8]; /* starts at 0x7ff8 */
+#ifdef CONFIG_SGI_IP27
+ u8 hour;
+ u8 min;
+ u8 sec;
+ u8 control;
+ u8 year;
+ u8 month;
+ u8 date;
+ u8 day;
+#else
u8 control;
u8 sec;
u8 min;
@@ -28,6 +38,7 @@ struct m48t35_rtc {
u8 date;
u8 month;
u8 year;
+#endif
};
#define M48T35_RTC_SET 0x80
diff --git a/drivers/tty/serial/8250/8250_ioc3.c b/drivers/tty/serial/8250/8250_ioc3.c
index 2be6ed2967e0..4c405f1b9c67 100644
--- a/drivers/tty/serial/8250/8250_ioc3.c
+++ b/drivers/tty/serial/8250/8250_ioc3.c
@@ -23,12 +23,12 @@ struct ioc3_8250_data {
static unsigned int ioc3_serial_in(struct uart_port *p, int offset)
{
- return readb(p->membase + offset);
+ return readb(p->membase + (offset ^ 3));
}
static void ioc3_serial_out(struct uart_port *p, int offset, int value)
{
- writeb(value, p->membase + offset);
+ writeb(value, p->membase + (offset ^ 3));
}
static int serial8250_ioc3_probe(struct platform_device *pdev)
--
2.13.7
