Hello Again Lee,
After a good night sleep few things came to my mind =)
On Thu, Feb 07, 2019 at 02:00:53PM +0000, Lee Jones wrote:
> On Thu, 07 Feb 2019, Matti Vaittinen wrote:
>
> > +
> > +static struct mfd_cell bd70528_mfd_cells[] = {
> > + { .name = "bd70528-pmic", },
> > + { .name = "bd70528-gpio", },
> > + /*
> > + * We use BD71837 driver to drive the clk block. Only differences to
> > + * BD70528 clock gate are the register address and mask.
> > + */
> > + { .name = "bd718xx-clk", },
> > + { .name = "bd70528-wdt", },
> > + {
> > + .name = "bd70528-power",
> > + .resources = &charger_irqs[0],
> > + .num_resources = ARRAY_SIZE(charger_irqs),
> > + },
> > + {
>
> These should be on the same line.
I know I said 'Ok' yesterday. And I can change the styling to what ever
suits you - but I am not entirely sure what you mean by this? Do you
mean that the brackets should be on same line? After a quick look to
few other MFD devices it seems to be common convention to have these on
separate lines - and such style is used also at other locations
throughout this file.
> > +static const struct regmap_access_table volatile_regs = {
> > + .yes_ranges = &volatile_ranges[0],
> > + .n_yes_ranges = ARRAY_SIZE(volatile_ranges),
> > +};
> > +
> > +static struct regmap_config bd70528_regmap = {
> > + .reg_bits = 8,
> > + .val_bits = 8,
> > + .volatile_table = &volatile_regs,
> > + .max_register = BD70528_MAX_REGISTER,
> > + .cache_type = REGCACHE_RBTREE,
> > +};
>
> '\n' here.
>
> > +/* bit [0] - Shutdown register */
> > +unsigned int bit0_offsets[] = {0};
> > +/* bit [1] - Power failure register */
> > +unsigned int bit1_offsets[] = {1};
> > +/* bit [2] - VR FAULT register */
> > +unsigned int bit2_offsets[] = {2};
> > +/* bit [3] - PMU register interrupts */
> > +unsigned int bit3_offsets[] = {3};
> > +/* bit [4] - Charger 1 and Charger 2 registers */
> > +unsigned int bit4_offsets[] = {4, 5};
> > +/* bit [5] - RTC register */
> > +unsigned int bit5_offsets[] = {6};
> > +/* bit [6] - GPIO register */
> > +unsigned int bit6_offsets[] = {7};
> > +/* bit [7] - Invalid operation register */
> > +unsigned int bit7_offsets[] = {8};
>
> What on earth is this?
Would this comment help:
/*
* Mapping of main IRQ register bits to sub irq register offsets so
* that we can access corect sub IRQ registers based on bits that
* are set in main IRQ register.
*/
/* bit [0] - Shutdown register */
unsigned int bit0_offsets[] = {0};
/* bit [1] - Power failure register */
unsigned int bit1_offsets[] = {1};
/* bit [2] - VR FAULT register */
unsigned int bit2_offsets[] = {2};
/* bit [3] - PMU register interrupts */
unsigned int bit3_offsets[] = {3};
/* bit [4] - Charger 1 and Charger 2 registers */
unsigned int bit4_offsets[] = {4, 5};
/* bit [5] - RTC register */
unsigned int bit5_offsets[] = {6};
/* bit [6] - GPIO register */
unsigned int bit6_offsets[] = {7};
/* bit [7] - Invalid operation register */
unsigned int bit7_offsets[] = {8};
> > +static int bd70528_wdt_set(struct bd70528 *bd70528, int enable, int *old_state)
> > +{
[..]
> > +}
>
> Shouldn't this be one in the WDT driver?
Maybe I should explain it like this:
/*
* Both the WDT and RTC drivers need to be able to control WDT. WDT uses
* RTC for timeouts and setting the RTC may trigger watchdog. Thus the
* RTC must disable the WDT when RTC time is set. We provide WDT disabling
* code from the MFD parent as we don't want to make direct dependency
* between RTC and WDT. Some may want to use only WDT or only RTC.
*/
#define WD_CTRL_MAGIC1 0x55
#define WD_CTRL_MAGIC2 0xAA
static int bd70528_wdt_set(struct bd70528 *bd70528, int enable, int *old_state)
{
> > + /*
> > + * Disallow type setting for all IRQs by default as
> > + * most of them do not support setting type.
> > + */
> > + for (i = 0; i < ARRAY_SIZE(irqs); i++)
> > + irqs[i].type.types_supported = 0;
> > +
> > + irqs[BD70528_INT_GPIO0].type.type_reg_offset = 0;
> > + irqs[BD70528_INT_GPIO0].type.type_rising_val = 0x20;
> > + irqs[BD70528_INT_GPIO0].type.type_falling_val = 0x10;
> > + irqs[BD70528_INT_GPIO0].type.type_level_high_val = 0x40;
> > + irqs[BD70528_INT_GPIO0].type.type_level_low_val = 0x50;
> > + irqs[BD70528_INT_GPIO0].type.types_supported = (IRQ_TYPE_EDGE_BOTH |
> > + IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
> > + irqs[BD70528_INT_GPIO1].type.type_reg_offset = 2;
> > + irqs[BD70528_INT_GPIO1].type.type_rising_val = 0x20;
> > + irqs[BD70528_INT_GPIO1].type.type_falling_val = 0x10;
> > + irqs[BD70528_INT_GPIO1].type.type_level_high_val = 0x40;
> > + irqs[BD70528_INT_GPIO1].type.type_level_low_val = 0x50;
> > + irqs[BD70528_INT_GPIO1].type.types_supported = (IRQ_TYPE_EDGE_BOTH |
> > + IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
> > + irqs[BD70528_INT_GPIO2].type.type_reg_offset = 4;
> > + irqs[BD70528_INT_GPIO2].type.type_rising_val = 0x20;
> > + irqs[BD70528_INT_GPIO2].type.type_falling_val = 0x10;
> > + irqs[BD70528_INT_GPIO2].type.type_level_high_val = 0x40;
> > + irqs[BD70528_INT_GPIO2].type.type_level_low_val = 0x50;
> > + irqs[BD70528_INT_GPIO2].type.types_supported = (IRQ_TYPE_EDGE_BOTH |
> > + IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
> > + irqs[BD70528_INT_GPIO3].type.type_reg_offset = 6;
> > + irqs[BD70528_INT_GPIO3].type.type_rising_val = 0x20;
> > + irqs[BD70528_INT_GPIO3].type.type_falling_val = 0x10;
> > + irqs[BD70528_INT_GPIO3].type.type_level_high_val = 0x40;
> > + irqs[BD70528_INT_GPIO3].type.type_level_low_val = 0x50;
> > + irqs[BD70528_INT_GPIO3].type.types_supported = (IRQ_TYPE_EDGE_BOTH |
> > + IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
>
> Could you please explain:
>
> a) what you're doing here
> b) why you don't mass assign them
> - seeing as most of the data is identical.
I am not sure this is what you meant by mass assignment? Something like
below?
I think this makes the code slightly more confusing yet much shorter.
What would you say? Is this what you had in mind?
/*
* Set IRQ typesetting information for GPIO pins 0 - 3
*/
for (i = 0; i < 4; i++) {
struct regmap_irq_type *type;
type = &irqs[BD70528_INT_GPIO0 + i].type;
type->type_reg_offset = 2 * i;
type-<type_rising_val = 0x20;
type->type_falling_val = 0x10;
type->type_level_high_val = 0x40;
type->type_level_low_val = 0x50;
type->types_supported = (IRQ_TYPE_EDGE_BOTH |
IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_LEVEL_LOW);
}
Br,
Matti Vaittinen
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then, he vanished ~~~
