On Tue, Jan 23, 2018 at 01:18:01PM +0100, Michael Grzeschik wrote:
> We add support for the ISL1219 chip that got an integrated tamper
> detection function. This patch implements the feature by using an hwmon
> interface.
>
> The ISL1219 can also describe the timestamp of the intrusion
> event. For this we add the documentation of the new interface
> intrusion[0-*]_timestamp.
>
> The devicetree documentation for the ISL1219 device tree
> binding is added with an short example.
>
> Signed-off-by: Michael Grzeschik <m.grzeschik@xxxxxxxxxxxxxx>
> Signed-off-by: Denis Osterland <Denis.Osterland@xxxxxxxxx>
> ---
> .../rtc/{intersil,isl1208.txt => isil,isl1208.txt} | 18 +-
> Documentation/hwmon/sysfs-interface | 7 +
> drivers/rtc/rtc-isl1208.c | 190 +++++++++++++++++++--
> 3 files changed, 201 insertions(+), 14 deletions(-)
> rename Documentation/devicetree/bindings/rtc/{intersil,isl1208.txt => isil,isl1208.txt} (57%)
>
> diff --git a/Documentation/devicetree/bindings/rtc/intersil,isl1208.txt b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt
> similarity index 57%
> rename from Documentation/devicetree/bindings/rtc/intersil,isl1208.txt
> rename to Documentation/devicetree/bindings/rtc/isil,isl1208.txt
> index a54e99feae1ca..d549699e1cfc4 100644
> --- a/Documentation/devicetree/bindings/rtc/intersil,isl1208.txt
> +++ b/Documentation/devicetree/bindings/rtc/isil,isl1208.txt
> @@ -1,14 +1,21 @@
> -Intersil ISL1208, ISL1218 I2C RTC/Alarm chip
> +Intersil ISL1208, ISL1218, ISL1219 I2C RTC/Alarm chip
>
> ISL1208 is a trivial I2C device (it has simple device tree bindings,
> consisting of a compatible field, an address and possibly an interrupt
> line).
>
> +ISL1219 supports tamper detection user space representation through
> +case intrusion hwmon sensor.
User space and hwmon are Linux details not relevant to the binding. Just
describe the h/w.
> +ISL1219 has additional pins EVIN and #EVDET for tamper detection.
> +I2C devices support only one irq. #IRQ and #EVDET are open-drain active low,
> +so it is possible layout them to one SoC pin with pull-up.
> +
> Required properties supported by the device:
>
> - "compatible": must be one of
> "isil,isl1208"
> "isil,isl1218"
> + "isil,isl1219"
> - "reg": I2C bus address of the device
>
> Optional properties:
> @@ -33,3 +40,12 @@ Example isl1208 node with #IRQ pin connected to SoC gpio1 pin 12:
> interrupt-parent = <&gpio1>;
> interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
> };
> +
> +Example isl1219 node with #IRQ pin and #EVDET pin connected to SoC gpio1 pin 12:
> +
> + isl1219: isl1219@68 {
> + compatible = "intersil,isl1219";
> + reg = <0x68>;
> + interrupts-extended = <&gpio1 12 IRQ_TYPE_EDGE_FALLING>;
With 2 interrupts, you should have 2 values. If they are connected
together, just repeat the connection. Otherwise, you can't tell if EVDET
is a no connect.
There's not much point in having an example for every compatible. This
binding is simple enough, one should be enough.
> + };
> +
