"printk: move console printing to kthreads" breaks NFS boot on i.MX8

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello,

I have an i.MX8 board here (NXP's EVK) and booting it with the rootfs on
NFS fails like below on v5.11.4-rt11:

	...
	[    0.531118] mmc2: new HS400 MMC card at address 0001
	[    0.531658] mmcblk2: mmc2:0001 DG4032 29.1 GiB
	[    0.531820] mmcblk2boot0: mmc2:0001 DG4032 partition 1 4.00 MiB
	[    0.531988] mmcblk2boot1: mmc2:0001 DG4032 partition 2 4.00 MiB
	[    0.532116] mmcblk2rpmb: mmc2:0001 DG4032 partition 3 4.00 MiB, chardev (240:0)
	[    0.551648]  mmcblk2: p1 p2
	[    0.571698] mmc1: host does not support reading read-only switch, assuming write-enable
	[    0.582270] mmc1: new SDHC card at address b368
	[    0.582731] mmcblk1: mmc1:b368 SDC   3.84 GiB
	[    0.599759]  mmcblk1: p1
	[    4.351592] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
	[    4.374722] Sending DHCP requests .
	[    6.942718] .
	[   11.438718] .
	[   19.302718] .
	[   33.054718] .
	[   57.118718] .
	[   87.118717]  timed out!
	[   87.125308] IP-Config: Retrying forever (NFS root)...
	[   87.129137] RTL8211F Gigabit Ethernet 30be0000.ethernet-1:01: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL)
	[   91.231580] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
	[   91.262719] Sending DHCP requests .
	[   93.766718] .
	[   98.142718] .
	[  105.790718] .
	[  119.174718] .
	[  142.598718] .
	[  172.598718]  timed out!
	[  172.605397] IP-Config: Retrying forever (NFS root)...
	[  172.609252] RTL8211F Gigabit Ethernet 30be0000.ethernet-1:01: attached PHY driver (mii_bus:phy_addr=30be0000.ethernet-1:01, irq=POLL)
	[  176.703574] fec 30be0000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
	[  176.730720] Sending DHCP requests .
	[  179.178718] .
	[  183.458718] .
	[  190.938718] .
	...

(with DEBUG defined in net/ipv4/ipconfig.c).

I bisected and identified

	42afcbce7b62 (printk: move console printing to kthreads)

as the problematic commit. I just double checked that 42afcbce7b62 is
indeed bad and it's parent boots just fine.

I didn't start to look into what is the actual problem yet. Does this
ring a bell? Do you have a hint how to debug this?

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [RT Stable]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Video 4 Linux]     [Device Mapper]

  Powered by Linux