Hi Enric,
Thank you very much for your review, comments below.
I'll leave this a bit more on review before resending with your
suggested fixes.
On Mon, 27 Apr 2020, Enric Balletbo i Serra
<enric.balletbo@xxxxxxxxxxxxx> wrote:
Hi Adrian
Thank you for your patch.
On 27/4/20 10:19, Adrian Ratiu wrote:
This adds support for the Synopsis DesignWare MIPI DSI v1.01
host controller which is embedded in i.MX 6 SoCs. Based on
following patches, but updated/extended to work with existing
support found in the kernel: - drm: imx: Support Synopsys
DesignWare MIPI DSI host controller
Signed-off-by: Liu Ying <Ying.Liu@xxxxxxxxxxxxx>
Cc: Fabio Estevam <festevam@xxxxxxxxx> Cc: Enric Balletbo
Serra <eballetbo@xxxxxxxxx> Reviewed-by: Emil Velikov
<emil.velikov@xxxxxxxxxxxxx> Tested-by: Adrian Pop
<pop.adrian61@xxxxxxxxx> Tested-by: Arnaud Ferraris
<arnaud.ferraris@xxxxxxxxxxxxx> Signed-off-by: Sjoerd Simons
<sjoerd.simons@xxxxxxxxxxxxx> Signed-off-by: Martyn Welch
<martyn.welch@xxxxxxxxxxxxx> Signed-off-by: Adrian Ratiu
<adrian.ratiu@xxxxxxxxxxxxx> --- Changes since v7:
- Removed encoder helper ops and added drm_bridge (Laurent) -
Brought back drm_simple_encoder_init and dropped dependency
on external unify encoder creation patch (Laurent) - Minor
typo fixes
Changes since v6:
- Replaced custom noop encoder with the simple drm encoder
(Enric) - Added CONFIG_DRM_IMX6_MIPI_DSI depends on CONFIG_OF
(Enric) - Dropped imx_mipi_dsi_register() because now it only
creates the dummy encoder which can easily be done directly
in imx_dsi_bind()
Changes since v5:
- Reword to remove unrelated device tree patch mention
(Fabio) - Move pllref_clk enable/disable to bind/unbind
(Ezequiel) - Fix freescale.com -> nxp.com email addresses
(Fabio) - Also added myself as module author (Fabio) - Use
DRM_DEV_* macros for consistency, print more error msg
Changes since v4:
- Split off driver-specific configuration of phy timings due
to new upstream API. - Move regmap infrastructure logic to
separate commit (Ezequiel) - Move dsi v1.01 layout addition
to a separate commit (Ezequiel) - Minor warnings and driver
name fixes
Changes since v3:
- Renamed platform driver to reflect it's i.MX6 only. (Fabio)
Changes since v2:
- Fixed commit tags. (Emil)
Changes since v1:
- Moved register definitions & regmap initialization into
bridge module. Platform drivers get the regmap via plat_data
after calling the bridge probe. (Emil)
---
drivers/gpu/drm/imx/Kconfig | 8 +
drivers/gpu/drm/imx/Makefile | 1 +
drivers/gpu/drm/imx/dw_mipi_dsi-imx6.c | 399
+++++++++++++++++++++++++ 3 files changed, 408 insertions(+)
create mode 100644 drivers/gpu/drm/imx/dw_mipi_dsi-imx6.c
diff --git a/drivers/gpu/drm/imx/Kconfig
b/drivers/gpu/drm/imx/Kconfig index
207bf7409dfba..0dffc72df7922 100644 ---
a/drivers/gpu/drm/imx/Kconfig +++ b/drivers/gpu/drm/imx/Kconfig
@@ -39,3 +39,11 @@ config DRM_IMX_HDMI
depends on DRM_IMX help Choose this if you want to use
HDMI on i.MX6.
+ +config DRM_IMX6_MIPI_DSI + tristate "Freescale i.MX6
DRM MIPI DSI" + select DRM_DW_MIPI_DSI + depends on
DRM_IMX + depends on OF + help + Choose this if you want
to use MIPI DSI on i.MX6. diff --git
a/drivers/gpu/drm/imx/Makefile b/drivers/gpu/drm/imx/Makefile
index 21cdcc2faabc8..9a7843c593478 100644 ---
a/drivers/gpu/drm/imx/Makefile +++
b/drivers/gpu/drm/imx/Makefile @@ -9,3 +9,4 @@
obj-$(CONFIG_DRM_IMX_TVE) += imx-tve.o
obj-$(CONFIG_DRM_IMX_LDB) += imx-ldb.o
obj-$(CONFIG_DRM_IMX_HDMI) += dw_hdmi-imx.o
+obj-$(CONFIG_DRM_IMX6_MIPI_DSI) += dw_mipi_dsi-imx6.o diff
--git a/drivers/gpu/drm/imx/dw_mipi_dsi-imx6.c
b/drivers/gpu/drm/imx/dw_mipi_dsi-imx6.c new file mode 100644
index 0000000000000..492decc418bc3 --- /dev/null +++
b/drivers/gpu/drm/imx/dw_mipi_dsi-imx6.c @@ -0,0 +1,399 @@ +//
SPDX-License-Identifier: GPL-2.0+ +/* + * i.MX6 drm driver -
MIPI DSI Host Controller + * + * Copyright (C) 2011-2015
Freescale Semiconductor, Inc. + * Copyright (C) 2019-2020
Collabora, Ltd. + */ + +#include <linux/clk.h> +#include
<linux/component.h> +#include <linux/mfd/syscon.h> +#include
<linux/mfd/syscon/imx6q-iomuxc-gpr.h> +#include
<linux/module.h> +#include <linux/of_device.h> +#include
<linux/regmap.h> +#include <linux/videodev2.h> +#include
<drm/bridge/dw_mipi_dsi.h> +#include
<drm/drm_atomic_state_helper.h> +#include
<drm/drm_crtc_helper.h> +#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_of.h> +#include <drm/drm_print.h> +#include
<drm/drm_simple_kms_helper.h> + +#include "imx-drm.h" +
+#define DSI_PWR_UP 0x04 +#define RESET
0 +#define POWERUP BIT(0) + +#define
DSI_PHY_IF_CTRL 0x5c +#define
PHY_IF_CTRL_RESET 0x0 + +#define DSI_PHY_TST_CTRL0
0x64 +#define PHY_TESTCLK BIT(1) +#define
PHY_UNTESTCLK 0 +#define PHY_TESTCLR
BIT(0) +#define PHY_UNTESTCLR 0 +
+#define DSI_PHY_TST_CTRL1 0x68 +#define PHY_TESTEN
BIT(16) +#define PHY_UNTESTEN 0 +#define
PHY_TESTDOUT(n) (((n) & 0xff) << 8)
+#define PHY_TESTDIN(n) (((n) & 0xff) <<
0) + +struct imx_mipi_dsi { + struct drm_encoder
encoder; + struct drm_bridge bridge; + struct device
*dev; + struct regmap *mux_sel; + struct dw_mipi_dsi
*mipi_dsi; + struct clk *pllref_clk; + + void __iomem
*base; + unsigned int lane_mbps; +}; + +struct
dphy_pll_testdin_map { + unsigned int max_mbps; + u8
testdin; +}; + +/* The table is based on 27MHz DPHY pll
reference clock. */ +static const struct dphy_pll_testdin_map
dptdin_map[] = { + {160, 0x04}, {180, 0x24}, {200, 0x44},
{210, 0x06}, + {240, 0x26}, {250, 0x46}, {270, 0x08},
{300, 0x28}, + {330, 0x48}, {360, 0x2a}, {400, 0x4a},
{450, 0x0c}, + {500, 0x2c}, {550, 0x0e}, {600, 0x2e},
{650, 0x10}, + {700, 0x30}, {750, 0x12}, {800, 0x32},
{850, 0x14}, + {900, 0x34}, {950, 0x54}, {1000, 0x74} +};
+ +static inline struct imx_mipi_dsi *bridge_to_imxdsi(struct
drm_bridge *br) +{ + return container_of(br, struct
imx_mipi_dsi, bridge); +} + +static int
+imx_mipi_dsi_bridge_atomic_check(struct drm_bridge *bridge, +
struct drm_bridge_state *bridge_state, +
struct drm_crtc_state *crtc_state, +
struct drm_connector_state *conn_state) +{ + struct
imx_crtc_state *imx_crtc_state = to_imx_crtc_state(crtc_state);
+ + /* The following values are taken from
dw_hdmi_imx_atomic_check */ + imx_crtc_state->bus_format
= MEDIA_BUS_FMT_RGB888_1X24; +
imx_crtc_state->di_hsync_pin = 2; +
imx_crtc_state->di_vsync_pin = 3; + + return 0; +} +
+static void imx_mipi_dsi_bridge_atomic_enable(struct
drm_bridge *bridge, +
struct drm_bridge_state *old_st) +{ + struct
imx_mipi_dsi *dsi = bridge_to_imxdsi(bridge); + int mux =
drm_of_encoder_active_port_id(dsi->dev->of_node, +
&dsi->encoder); + /* Set IOMUX DSI output reg to correct IPU
1 or 0 and DI 1 or 0 ports */ +
regmap_update_bits(dsi->mux_sel, IOMUXC_GPR3, +
IMX6Q_GPR3_MIPI_MUX_CTL_MASK, + mux <<
IMX6Q_GPR3_MIPI_MUX_CTL_SHIFT); +} + +static const struct
drm_bridge_funcs imx_dsi_bridge_funcs = { + .atomic_enable =
imx_mipi_dsi_bridge_atomic_enable, + .atomic_check =
imx_mipi_dsi_bridge_atomic_check, + .atomic_reset =
drm_atomic_helper_bridge_reset, + .atomic_duplicate_state =
drm_atomic_helper_bridge_duplicate_state, +
.atomic_destroy_state = drm_atomic_helper_bridge_destroy_state,
+}; + +static enum drm_mode_status imx_mipi_dsi_mode_valid(void
*priv_data, + const
struct drm_display_mode *mode) +{ + /* + * The
VID_PKT_SIZE field in the DSI_VID_PKT_CFG + * register is
11-bit. + */ + if (mode->hdisplay > 0x7ff) +
return MODE_BAD_HVALUE; + + /* + * The V_ACTIVE_LINES
field in the DSI_VTIMING_CFG + * register is 11-bit. +
*/ + if (mode->vdisplay > 0x7ff) + return
MODE_BAD_VVALUE; + + return MODE_OK; +} + + +static unsigned
int max_mbps_to_testdin(unsigned int max_mbps) +{ + unsigned
int i; + + for (i = 0; i < ARRAY_SIZE(dptdin_map); i++) +
if (dptdin_map[i].max_mbps == max_mbps) +
return dptdin_map[i].testdin; + + return -EINVAL; +} +
+static inline void dsi_write(struct imx_mipi_dsi *dsi, u32
reg, u32 val) +{ + writel(val, dsi->base + reg); +} + +static
int imx_mipi_dsi_phy_init(void *priv_data) +{ + struct
imx_mipi_dsi *dsi = priv_data; + int testdin; + +
testdin = max_mbps_to_testdin(dsi->lane_mbps); + if
(testdin < 0) { + DRM_DEV_ERROR(dsi->dev, +
"failed to get testdin for %dmbps lane clock\n", +
dsi->lane_mbps); + return testdin; + } + +
dsi_write(dsi, DSI_PHY_IF_CTRL, PHY_IF_CTRL_RESET); +
dsi_write(dsi, DSI_PWR_UP, POWERUP); + + dsi_write(dsi,
DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); +
dsi_write(dsi, DSI_PHY_TST_CTRL1, PHY_TESTEN | PHY_TESTDOUT(0)
| + PHY_TESTDIN(0x44)); + dsi_write(dsi,
DSI_PHY_TST_CTRL0, PHY_TESTCLK | PHY_UNTESTCLR); +
dsi_write(dsi, DSI_PHY_TST_CTRL0, PHY_UNTESTCLK |
PHY_UNTESTCLR); + dsi_write(dsi, DSI_PHY_TST_CTRL1,
PHY_UNTESTEN | PHY_TESTDOUT(0) | +
PHY_TESTDIN(testdin)); + dsi_write(dsi, DSI_PHY_TST_CTRL0,
PHY_TESTCLK | PHY_UNTESTCLR); + dsi_write(dsi,
DSI_PHY_TST_CTRL0, PHY_UNTESTCLK | PHY_UNTESTCLR); + +
return 0; +} + +static int imx_mipi_dsi_get_lane_mbps(void
*priv_data, + const struct
drm_display_mode *mode, +
unsigned long mode_flags, u32 lanes, +
u32 format, unsigned int *lane_mbps) +{ + struct
imx_mipi_dsi *dsi = priv_data; + int bpp; + unsigned
int i, target_mbps, mpclk; + unsigned long pllref; + +
bpp = mipi_dsi_pixel_format_to_bpp(format); + if (bpp <
0) { + DRM_DEV_ERROR(dsi->dev, "failed to get bpp
for format %d: %d\n", + format,
bpp); + return bpp; + } + + pllref =
clk_get_rate(dsi->pllref_clk); + if (pllref != 27000000) +
DRM_WARN("DSI pllref_clk not set to 27Mhz\n");
This pllref variable is only used to print this warning, what's
the point of warn and ignore it? If pllref is not set at 27MHz
what will happen?
According to the imx6 ref manual, 27Mhz is the maximum value of
the D-PHY TX refclk used to drive the display in high-speed mode
(in low power modes this clock is disabled). It's range is [6,27]
Mhz.
The manual-provided tables and examples for operating the
controller always assumes the ref clk is set to 27Mhz which allows
a maximum of
1Ghz pll and 125 Mhz byte clocks achieving 1000 lane mbps.
This driver does the same thing as the imx manual if you look at
the definition of `dptdin_map` above which is used to compute the
maximum lane speed for the specific mode clock.
In theory I guess power consumption can be lowered by using a
less-than max value for the refclk, but I've never seen this done
in practice and is very application specific... Of course, if this
is a real power-save gain and people care about it, optimized
tables can be added later :)
If refclk is not set to 27Mhz, in the worst case, the
configuration done in imx_mipi_dsi_phy_init() and
imx_mipi_dsi_get_lane_mbps() based on the values provided in
`dptdin_map` won't be able to drive the display.
So I guess the best course of action is to drop this warn and make
it an error in the platform driver bind() when enabling the clock,
right?
+ + mpclk = DIV_ROUND_UP(mode->clock, MSEC_PER_SEC); + if
(mpclk) { + /* take 1/0.7 blanking overhead into
consideration */ + target_mbps = (mpclk * (bpp /
lanes) * 10) / 7; + } else { +
DRM_DEV_ERROR(dsi->dev, "use default 1Gbps DPHY pll clock\n");
That's really an error? Looks to me that's just a fallback if
mpclk is zero. Maybe set the level to INFO or even better
DEBUG.
Yes, I will do this and all the other suggestions you made
below. Thanks!
BTW I also noticed the below prints are wrong, will also fix them.
+ target_mbps = 1000; + } + +
DRM_DEV_DEBUG(dsi->dev, "target pllref_clk frequency is
%uMbps\n", + target_mbps); + + for (i = 0; i <
ARRAY_SIZE(dptdin_map); i++) { + if (target_mbps <
dptdin_map[i].max_mbps) { + *lane_mbps =
dptdin_map[i].max_mbps; + dsi->lane_mbps =
*lane_mbps; + DRM_DEV_DEBUG(dsi->dev, +
"real pllref_clk frequency is %uMbps\n", +
*lane_mbps); + return 0; + }
+ } + + DRM_DEV_ERROR(dsi->dev, "DPHY clock frequency
%uMbps is out of range\n", + target_mbps); + +
return -EINVAL; +} + +static int
+dw_mipi_dsi_phy_get_timing(void *priv_data, unsigned int
lane_mbps, + struct dw_mipi_dsi_dphy_timing
*timing) +{ + timing->clk_hs2lp = 0x40; +
timing->clk_lp2hs = 0x40; + timing->data_hs2lp = 0x40; +
timing->data_lp2hs = 0x40; + + return 0; +} + +static
const struct dw_mipi_dsi_phy_ops dw_mipi_dsi_imx6_phy_ops = { +
.init = imx_mipi_dsi_phy_init, + .get_lane_mbps =
imx_mipi_dsi_get_lane_mbps, + .get_timing =
dw_mipi_dsi_phy_get_timing, +}; + +static struct
dw_mipi_dsi_plat_data imx6_mipi_dsi_drv_data = { +
.max_data_lanes = 2, + .mode_valid =
imx_mipi_dsi_mode_valid, + .phy_ops =
&dw_mipi_dsi_imx6_phy_ops, +}; + +static const struct
of_device_id imx_dsi_dt_ids[] = { + { +
.compatible = "fsl,imx6-mipi-dsi", + .data =
&imx6_mipi_dsi_drv_data, + }, + { /* sentinel */ } +};
+MODULE_DEVICE_TABLE(of, imx_dsi_dt_ids); + +static int
imx_mipi_dsi_bind(struct device *dev, struct device *master, +
void *data) +{ + struct imx_mipi_dsi *dsi =
dev_get_drvdata(dev); + struct drm_device *drm = data; +
int ret; + + ret = clk_prepare_enable(dsi->pllref_clk); + if
(ret) { + DRM_DEV_ERROR(dev, "Failed to enable
pllref_clk: %d\n", ret); + return ret; + } + +
ret = imx_drm_encoder_parse_of(drm, &dsi->encoder,
dsi->dev->of_node); + if (ret) + return
ret; + + ret = drm_simple_encoder_init(drm, &dsi->encoder,
DRM_MODE_ENCODER_NONE); + if (ret) { +
DRM_DEV_ERROR(dev, "failed to create drm encoder\n"); +
return ret; + } + + drm_bridge_add(&dsi->bridge);
You are adding the bridge in imx_mipi_dsi_bind() but removing in
imx_mipi_dsi_remove(). Although in this case I don't think there
is any bad effect, would be nice maintain the symetry, so I'd
move the drm_bridge_add() call to the imx_mipi_dis_probe()
function just before component_add().
+ + drm_bridge_attach(&dsi->encoder, &dsi->bridge, NULL, 0); +
if (ret < 0) { + DRM_DEV_ERROR(dev, "failed to
attach IMX6 bridge: %d\n", ret); + return ret;
If it fails you probably want to cleanup the encoder
drm_cleanup_encoder()
+ }
+
+ ret = dw_mipi_dsi_bind(dsi->mipi_dsi, &dsi->encoder, &dsi->bridge);
+ if (ret) {
+ DRM_DEV_ERROR(dev, "Failed to bind: %d\n", ret);
+ return ret;
The same here.
+ }
+
+ return 0;
+}
+
+static void imx_mipi_dsi_unbind(struct device *dev, struct device *master,
+ void *data)
+{
+ struct imx_mipi_dsi *dsi = dev_get_drvdata(dev);
+
+ dw_mipi_dsi_unbind(dsi->mipi_dsi);
+
drm_encoder_cleanup() ?
+ clk_disable_unprepare(dsi->pllref_clk);
+}
+
+static const struct component_ops imx_mipi_dsi_ops = {
+ .bind = imx_mipi_dsi_bind,
+ .unbind = imx_mipi_dsi_unbind,
+};
+
+static int imx_mipi_dsi_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ const struct of_device_id *of_id = of_match_device(imx_dsi_dt_ids, dev);
+ struct dw_mipi_dsi_plat_data *pdata = (struct dw_mipi_dsi_plat_data *) of_id->data;
+ struct imx_mipi_dsi *dsi;
+ struct resource *res;
+ int ret;
+
+ dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL);
+ if (!dsi)
+ return -ENOMEM;
+
+ dsi->dev = dev;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ dsi->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(dsi->base)) {
+ ret = PTR_ERR(dsi->base);
+ DRM_DEV_ERROR(dev, "Unable to get dsi registers: %d\n", ret);
+ return ret;
This print is redundant, devm_ioremap_resource will print an error already. This
code can be simply
return PTR_ERR(res);
+ }
+
+ dsi->pllref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(dsi->pllref_clk)) {
+ ret = PTR_ERR(dsi->pllref_clk);
+ DRM_DEV_ERROR(dev, "Unable to get pllref_clk: %d\n", ret);
This print is redundant, devm_clk_get will print an error already. This code can
be simply
return PTR_ERR(dsi->pllref_clk);
+ return ret;
+ }
+
+ dsi->mux_sel = syscon_regmap_lookup_by_phandle(dev->of_node, "fsl,gpr");
+ if (IS_ERR(dsi->mux_sel)) {
+ ret = PTR_ERR(dsi->mux_sel);
+ DRM_DEV_ERROR(dev, "Failed to get GPR regmap: %d\n", ret);
+ return ret;
+ }
+
+ dev_set_drvdata(dev, dsi);
+
+ imx6_mipi_dsi_drv_data.base = dsi->base;
+ imx6_mipi_dsi_drv_data.priv_data = dsi;
+
+ dsi->bridge.driver_private = dsi;
+ dsi->bridge.funcs = &imx_dsi_bridge_funcs;
+ dsi->bridge.of_node = dev->of_node;
You probably want to set the bridge.type here too:
dsi->bridge.type = DRM_MODE_CONNECTOR_DSI;
+
+ dsi->mipi_dsi = dw_mipi_dsi_probe(pdev, pdata);
+ if (IS_ERR(dsi->mipi_dsi)) {
+ ret = PTR_ERR(dsi->mipi_dsi);
+ DRM_DEV_ERROR(dev, "Failed to probe DW DSI host: %d\n", ret);
+ goto err_clkdisable;
+ }
+
+ return component_add(&pdev->dev, &imx_mipi_dsi_ops);
+
+err_clkdisable:
+ clk_disable_unprepare(dsi->pllref_clk);
+ return ret;
+}
+
+static int imx_mipi_dsi_remove(struct platform_device *pdev)
+{
+ struct imx_mipi_dsi *dsi = platform_get_drvdata(pdev);
+ drm_bridge_remove(&dsi->bridge);
+ component_del(&pdev->dev, &imx_mipi_dsi_ops);
+ return 0;
+}
+
+static struct platform_driver imx_mipi_dsi_driver = {
+ .probe = imx_mipi_dsi_probe,
+ .remove = imx_mipi_dsi_remove,
+ .driver = {
+ .of_match_table = imx_dsi_dt_ids,
+ .name = "dw-mipi-dsi-imx6",
+ },
+};
+module_platform_driver(imx_mipi_dsi_driver);
+
+MODULE_DESCRIPTION("i.MX6 MIPI DSI host controller driver");
+MODULE_AUTHOR("Liu Ying <victor.liu@xxxxxxx>");
+MODULE_AUTHOR("Adrian Ratiu <adrian.ratiu@xxxxxxxxxxxxx>");
+MODULE_LICENSE("GPL");
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
