Hi Chen-Yu,
> From: Chen-Yu Tsai <wens@xxxxxxxx>
>
> With SDIO now enabled, the numbering of the existing MMC host controllers
> gets incremented by 1, as the SDIO host is the first one.
>
> Increment the numbering of the MMC LED triggers to match.
>
> Fixes: cf3c5397835f ("arm64: dts: rockchip: Enable sdio0 and uart0 on rk3399-roc-pc-mezzanine")
> Signed-off-by: Chen-Yu Tsai <wens@xxxxxxxx>
> ---
> arch/arm64/boot/dts/rockchip/rk3399-roc-pc-mezzanine.dts | 8 ++++++++
> arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi | 4 ++--
> 2 files changed, 10 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-mezzanine.dts b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-mezzanine.dts
> index 2acb3d500fb9..f0686fc276be 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-mezzanine.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc-mezzanine.dts
> @@ -38,6 +38,10 @@ vcc3v3_pcie: vcc3v3-pcie {
> };
> };
>
> +&diy_led {
> + linux,default-trigger = "mmc2";
> +};
> +
> &pcie_phy {
> status = "okay";
> };
> @@ -91,3 +95,7 @@ &uart0 {
> pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
> status = "okay";
> };
> +
> +&yellow_led {
> + linux,default-trigger = "mmc1";
> +};
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> index 9f225e9c3d54..bc060ac7972d 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
> @@ -70,14 +70,14 @@ work-led {
> linux,default-trigger = "heartbeat";
> };
>
> - diy-led {
> + diy_led: diy-led {
This changes an existing nodename into something that is still not the
preferred way. In the current Rockchip dts there are nodenames like
'work', 'yellow' that causing warnings with the command:
make -k ARCH=arm dtbs_check
Could you give a generic guide line/example, so all these changes are
treated the same way? As if the naming follows the preferred 'led-0' line.
> label = "red:diy";
> gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
> default-state = "off";
> linux,default-trigger = "mmc1";
> };
>
> - yellow-led {
> + yellow_led: yellow-led {
> label = "yellow:yellow-led";
> gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
> default-state = "off";
> --
> 2.26.0
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
