On Fri, Dec 27, 2019 at 6:49 PM Soeren Moch <smoch@xxxxxx> wrote: > > > > On 27.12.19 13:04, Jagan Teki wrote: > > On Fri, Dec 27, 2019 at 4:00 PM Soeren Moch <smoch@xxxxxx> wrote: > >> Hi! > >> > >> On 27.12.19 07:50, Jagan Teki wrote: > >>> Hi Kever, > >>> > >>> On Mon, Dec 23, 2019 at 8:04 AM Kever Yang <kever.yang@xxxxxxxxxxxxxx> wrote: > >>>> Jagan, > >>>> > >>>> > >>>> On 2019/12/21 下午3:54, Jagan Teki wrote: > >>>>> Most of the SPI flash devices in rockchip are 16MiB size. > >>>>> > >>>>> So, keeping U-Boot proper offset start from 128MiB with 1MiB > >>>>> size and then start env of 8KiB would be a compatible location > >>>>> between all variants of flash sizes. > >>>>> > >>>>> This patch add env start from 0x14000 with a size of 8KiB. > >>>> What's the space map in SPI flash suppose to be? Including > >>>> tpl/spl/u-boot.itb > >>>> > >>>> I would prefer to use 128KiB-8KiB as the env start address, we'd better > >>>> to avoid the > >>>> > >>>> risk of overlap between the env space and the firmware space. > >>> Here is the 16MiB flash layout, I have used. I can see the loader1 > >>> (tpl/spl) can be possible to load at 0x0 or 0x32K so I have given the > >>> space for it. and 8K env after loader2(u-boot). let me know your > >>> thoughts? > >> Why we cannot use the same layout as what is defined for SD/eMMC: > >> http://opensource.rock-chips.com/wiki_Partitions > >> > >> > >> > >>> 0x0 - 0x8000, 32K => reserved/loader1 > >>> 0x8000 - 0x40000, 224K => loader1 > >>> 0x40000 - 0x140000, 1M => loader2 > >>> 0x140000 - 0x142000, 8K => env > >>> 0x142000 - 0x842000, 7M => kernel > >>> 0x842000 - 0x853800, 100K => dtb > >>> 0x853800 - => root > >> These small loader1/loader2 partitions may byte us later when newer > >> u-boot versions only will fit for SD and not for SPI anymore. > > Yes, the initial idea is to reuse the existing SD layout but the SPI > > flash is limited in size, and it is further limited in rk3399 boards > > (rockpro64, roc-rk3399-pc..). which is 16MiB. So reusing half of the > > flash size will occupy for till loader2 in SD scheme. > Exactly. On my RockPro64 SPI flash size is 16MiB. This covers everything > up to "boot", especially loader1, loader2, and U-Boot ENV. Probably the > SPI on these boards is sized this way to exactly match this use case. > What should be the advantage of only using half of the available memory? To make small systems to full use of Flash. unlike distros, the embedded systems that run just with initramfs. Or any update mechanism in systems to make flash boot as an update agent and SD or other mediums as main systems. > >> The reserved space for kernel is already too small for normal kernel > >> builds today, not to mention a root filesystem. > >> > >> Are there any use cases where somebody needs to place boot and root > >> partitions on SPI flash? > > So, explained above due to size limitation the respective blocks like > > kernel, root (we can say initrd) are indeed less-sized partitions. > > Moreover SPI flash is not a suitable storage for rootfs in rockchip, > > since the boot order start from SPI flash usually board would boot > > from flash and then look for SD, eMMC, PCIe NVM for loading big chunk > > rootfs. > > > > More or less the idea of above flash layout is to fit properly > > with-in-the size boundaries and indeed for small initramfs systems. > We use distroboot in the defconfigs of these boards, so no separate > space for kernel or initrd is required in (raw) flash, these blobs are > always loaded from the boot partition instead. > Besides that, kernels for my RockPro64 are bigger (12MiB - 20MiB) than > the availbale space in SPI anyway, with additional ~5MiB for initrd. As I explained above. So, we can skip Linux, rootfs from flash and make use of flash layout that compatible between all systems. what is the issue with that other than future proof with SD layout. I understand your point, but each and every storage medium can have it's own usage to make use of full system running. So the partition layout would depend on the size and file systems but it shouldn't depend on particular software usage, IMHO. > > My use case for SPI would be to store u-boot+SPL+TPL+ATF+environment > there, so that I can use a single combined root+boot partition on a SD > card / USB disk. > So I think the easiest, least confusing, and future-proof SPI partition > scheme would be to use exactly what is defined already for SD/eMMC. Less confused in terms of maintenance and easy to understand but it may not be used for some corner cases like smaller systems. Jagan. _______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip
