Hi Soeren, Am Dienstag, 10. Dezember 2019, 00:29:21 CET schrieb Soeren Moch: > On 10.12.19 00:08, Heiko Stübner wrote: > > Am Montag, 9. Dezember 2019, 23:38:22 CET schrieb Soeren Moch: > >> RockPro64 supports an Ampak AP6359SA based wifi/bt combo module. > >> The BCM4359/9 wifi controller in this module is connected to sdio0, > >> enable this interface. > >> > >> Signed-off-by: Soeren Moch <smoch@xxxxxx> > >> --- > >> Not sure where to place exactly the sdio0 node in the dts because > >> existing sd nodes are not sorted alphabetically. > >> > >> This last patch in this brcmfmac patch series probably should be picked > >> up by Heiko independently of the rest of this series. It was sent together > >> to show how this brcmfmac extension for 4359-sdio support with RSDB is > >> used and tested. > > node placement looks good so I can apply it, just a general questions > > I only got patch 8/8 are patches 1-7 relevant for this one and what are they? > Patches 1-7 are the patches to support the BCM4359 chipset with SDIO > interface in the linux brcmfmac net-wireless driver, see [1]. > > So this patch series has 2 parts: > patches 1-7: add support for the wifi chipset in the wireless driver, > this has to go through net-wireless > patch 8: enable the wifi module with this chipset on RockPro64, this patch Thanks for the clarification :-) . As patch 8 "only" does the core sdio node, it doesn't really depend on the earlier ones and you can submit any uart-hooks for bluetooth once the other patches land I guess. > If this was confusing, what would be the ideal way to post such series? I think every maintainer has some slightly different perspective on this, but personally I like getting the whole series to follow the discussion but also to just see when the driver-side changes get merged, as the dts-parts need to wait for that in a lot of cases. Heiko > [1] https://patchwork.kernel.org/project/linux-wireless/list/?series=213951 > > > > Thanks > > Heiko > > > > > >> Cc: Heiko Stuebner <heiko@xxxxxxxxx> > >> Cc: Kalle Valo <kvalo@xxxxxxxxxxxxxx> > >> Cc: linux-wireless@xxxxxxxxxxxxxxx > >> Cc: brcm80211-dev-list.pdl@xxxxxxxxxxxx > >> Cc: brcm80211-dev-list@xxxxxxxxxxx > >> Cc: netdev@xxxxxxxxxxxxxxx > >> Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > >> Cc: linux-rockchip@xxxxxxxxxxxxxxxxxxx > >> Cc: linux-kernel@xxxxxxxxxxxxxxx > >> --- > >> .../boot/dts/rockchip/rk3399-rockpro64.dts | 21 ++++++++++++------- > >> 1 file changed, 14 insertions(+), 7 deletions(-) > >> > >> diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts > >> index 7f4b2eba31d4..9fa92790d6e0 100644 > >> --- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts > >> +++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dts > >> @@ -71,13 +71,6 @@ > >> clock-names = "ext_clock"; > >> pinctrl-names = "default"; > >> pinctrl-0 = <&wifi_enable_h>; > >> - > >> - /* > >> - * On the module itself this is one of these (depending > >> - * on the actual card populated): > >> - * - SDIO_RESET_L_WL_REG_ON > >> - * - PDN (power down when low) > >> - */ > >> reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>; > >> }; > >> > >> @@ -650,6 +643,20 @@ > >> status = "okay"; > >> }; > >> > >> +&sdio0 { > >> + bus-width = <4>; > >> + cap-sd-highspeed; > >> + cap-sdio-irq; > >> + disable-wp; > >> + keep-power-in-suspend; > >> + mmc-pwrseq = <&sdio_pwrseq>; > >> + non-removable; > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>; > >> + sd-uhs-sdr104; > >> + status = "okay"; > >> +}; > >> + > >> &sdmmc { > >> bus-width = <4>; > >> cap-sd-highspeed; > >> -- > >> 2.17.1 > >> > > > > > > > > _______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip
