Hi Kever, Am Dienstag, 27. August 2019, 03:54:26 CEST schrieb Kever Yang: > On 2019/8/27 上午1:09, Kevin Hilman wrote: > > Kever Yang <kever.yang@xxxxxxxxxxxxxx> writes: > >> I want to have a test with my board, I can get the Image and dtb > >> from the link for the job, > >> > >> but how can I get the randisk which is named initrd-SDbyy2.cpio.gz? > > The ramdisk images are here: > > > > https://storage.kernelci.org/images/rootfs/buildroot/kci-2019.02/arm64/base/ > > > > in the kernelCI logs the ramdisk is slightly modified because the kernel > > modules have been inserted into the cpio archive. > > > > However, for the purposes of this test, you can just test with the > > unmodified rootfs.cpio.gz above. > > > I try with this ramdisk, and it hangs at fan53555 init, but not get into > cpufreq. > > Any suggestion? My guess would be the fcs,suspend-voltage-selector maybe? I.e. old uboots somehow set the voltage gpio strangely, so you'd need fcs,suspend-voltage-selector = <0> while newer uboots I think do configure the gpio, needing a value of <1>; So try to swap that number in the dts perhaps for a start? Heiko > My boot log: > > https://paste.ubuntu.com/p/WYZKPWp7sk/ > > Thanks, > > - Kever > > > > > Kevin > > > > > >> Thanks, > >> > >> - Kever > >> > >> On 2019/8/24 上午1:03, Kevin Hilman wrote: > >>> Kevin Hilman <khilman@xxxxxxxxxxxx> writes: > >>> > >>>> Kever Yang <kever.yang@xxxxxxxxxxxxxx> writes: > >>>> > >>>>> Hi Kevin, Heiko, > >>>>> > >>>>> On 2019/8/22 上午2:59, Kevin Hilman wrote: > >>>>>> Hi Heiko, > >>>>>> > >>>>>> Heiko Stuebner <heiko@xxxxxxxxx> writes: > >>>>>> > >>>>>>> Am Dienstag, 13. August 2019, 19:35:31 CEST schrieb Kevin Hilman: > >>>>>>>> [ resent with correct addr for linux-rockchip list ] > >>>>>>>> > >>>>>>>> Mark Brown <broonie@xxxxxxxxxx> writes: > >>>>>>>> > >>>>>>>>> On Thu, Jul 18, 2019 at 04:28:08AM -0700, kernelci.org bot wrote: > >>>>>>>>> > >>>>>>>>> Today's -next started failing to boot defconfig on rk3399-firefly: > >>>>>>>>> > >>>>>>>>>> arm64: > >>>>>>>>>> defconfig: > >>>>>>>>>> gcc-8: > >>>>>>>>>> rk3399-firefly: 1 failed lab > >>>>>>>>> It hits a BUG() trying to set up cpufreq: > >>>>>>>>> > >>>>>>>>> [ 87.381606] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 200000 KHz > >>>>>>>>> [ 87.393244] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 408000 KHz > >>>>>>>>> [ 87.469777] cpufreq: cpufreq_online: CPU4: Running at unlisted freq: 12000 KHz > >>>>>>>>> [ 87.488595] cpu cpu4: _generic_set_opp_clk_only: failed to set clock rate: -22 > >>>>>>>>> [ 87.491881] cpufreq: __target_index: Failed to change cpu frequency: -22 > >>>>>>>>> [ 87.495335] ------------[ cut here ]------------ > >>>>>>>>> [ 87.496821] kernel BUG at drivers/cpufreq/cpufreq.c:1438! > >>>>>>>>> [ 87.498462] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP > >>>>>>>>> > >>>>>>>>> I'm struggling to see anything relevant in the diff from yesterday, the > >>>>>>>>> unlisted frequency warnings were there in the logs yesterday but no oops > >>>>>>>>> and I'm not seeing any changes in cpufreq, clk or anything relevant > >>>>>>>>> looking. > >>>>>>>>> > >>>>>>>>> Full bootlog and other info can be found here: > >>>>>>>>> > >>>>>>>>> https://kernelci.org/boot/id/5d302d8359b51498d049e983/ > >>>>>>>> I confirm that disabling CPUfreq in the defconfig (CONFIG_CPU_FREQ=n) > >>>>>>>> makes the firefly board start working again. > >>>>>>>> > >>>>>>>> Note that the default defconfig enables the "performance" CPUfreq > >>>>>>>> governor as the default governor, so during kernel boot, it will always > >>>>>>>> switch to the max frequency. > >>>>>>>> > >>>>>>>> For fun, I set the default governor to "userspace" so the kernel > >>>>>>>> wouldn't make any OPP changes, and that leads to a slightly more > >>>>>>>> informative splat[1] > >>>>>>>> > >>>>>>>> There is still an OPP change happening because the detected OPP is not > >>>>>>>> one that's listed in the table, so it tries to change to a listed OPP > >>>>>>>> and fails in the bowels of clk_set_rate() > >>>>>>> Though I think that might only be a symptom as well. > >>>>>>> Both the PLL setting code as well as the actual cpu-clock implementation > >>>>>>> is unchanged since 2017 (and runs just fine on all boards in my farm). > >>>>>>> > >>>>>>> One source for these issues is often the regulator supplying the cpu > >>>>>>> going haywire - aka the voltage not matching the opp. > >>>>>>> > >>>>>>> As in this error-case it's CPU4 being set, this would mean it might > >>>>>>> be the big cluster supplied by the external syr825 (fan5355 clone) > >>>>>>> that might act up. In the Firefly-rk3399 case this is even stranger. > >>>>>>> > >>>>>>> There is a discrepancy between the "fcs,suspend-voltage-selector" > >>>>>>> between different bootloader versions (how the selection-pin is set up), > >>>>>>> so the kernel might actually write his requested voltage to the wrong > >>>>>>> register (not the one for actual voltage, but the second set used for > >>>>>>> the suspend voltage). > >>>>>>> > >>>>>>> Did you by chance swap bootloaders at some point in recent past? > >>>>>> No, haven't touched bootloader since I initially setup the board. > >>>>> The CPU voltage does not affect by bootloader for kernel should have its > >>>>> own opp-table, > >>>>> > >>>>> the bootloader may only affect the center/logic power supply. > >>>>> > >>>>>>> I'd assume [2] might actually be the same issue last year, though > >>>>>>> the CI-logs are not available anymore it seems. > >>>>>>> > >>>>>>> Could you try to set the vdd_cpu_b regulator to disabled, so that > >>>>>>> cpufreq for this cluster defers and see what happens? > >>>>>> Yes, this change[1] definitely makes things boot reliably again, so > >>>>>> there's defintiely something a bit unstable with this regulator, at > >>>>>> least on this firefly. > >>>>> Is it possible to target which patch introduce this bug? This board > >>>>> should have work correctly for a long time with upstream source code. > >>>> Unfortunately, it seems to be a regular, but intermittent failure, so > >>>> bisection is not producing anything reliable. > >>>> > >>>> You can see that both in mainline[1] and in linux-next[2] there are > >>>> periodic failures, but it's hard to see any patterns. > >>> Even worse, I (re)tested mainline for versions that were previously > >>> passing (v5.2, v5.3-rc5) and they are also failing now. > >>> > >>> They work again if I disable that regulator as suggested by Heiko. > >>> > >>> So this is increasingly pointing to failing hardware. > >>> > >>> Kevin > >>> > >>> > >>> > > > > > > > _______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip
