Στις Πεμ, 14 Μαρ, 2019 at 9:02 ΜΜ, ο/η Heiko
=?iso-8859-1?q?St=FCbner?= <heiko@xxxxxxxxx> έγραψε:
Hi,
Am Donnerstag, 14. März 2019, 19:20:35 CET schrieb Leonidas P.
Papadakos:
From: William Wu <william.wu@xxxxxxxxxxxxxx>
RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
core's general architecture. It can act as static xHCI host
controller, static device controller, USB 3.0/2.0 OTG basing
on ID of USB3.0 PHY.
Signed-off-by: William Wu <william.wu@xxxxxxxxxxxxxx>
Signed-off-by: Leonidas P. Papadakos <papadakospan@xxxxxxxxx>
the rk3328 usb3-phy has an issue with detecting any plugin events
after a previous device got removed - see the inno-usb3-phy driver
in the vendor kernel.
So once you unplug an usb device from the port it won't detect
a newly connected device. This is also the reason why the original
usb3 patches are still sitting around in my tree, as I don't want to
codify a binding that may not last once somebody actually manages
to go around that issue with kernel code - especially as the node
below claims to be compatible with the rk3399 dwc3.
Heiko
---
arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27
++++++++++++++++++++++++
1 file changed, 27 insertions(+)
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
b/arch/arm64/boot/dts/rockchip/rk3328.dtsi index
84f14b132..f5c1ab596
100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -917,6 +917,33 @@
status = "disabled";
};
+ usbdrd3: usb@ff600000 {
+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3";
+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>,
+ <&cru ACLK_USB3OTG>;
+ clock-names = "ref_clk", "suspend_clk",
+ "bus_clk";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usbdrd_dwc3: dwc3@ff600000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff600000 0x0 0x100000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+ snps,dis_enblslpm_quirk;
+ snps,dis-u2-freeclk-exists-quirk;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,dis-del-phy-power-chg-quirk;
+ snps,dis-tx-ipgap-linecheck-quirk;
+ status = "disabled";
+ };
+ };
+
gic: interrupt-controller@ff811000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
Now it makes sense. I thought it was board specific. It's a general
rk3328 issue, then.
Thanks for clearing it up. (yet again, oops)
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
