On Sun, Mar 3, 2019 at 2:40 PM David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx> wrote: > > And so synthesis on where we are on the WiFi patch for the Thinker Boards. > > There have been very few comments, only really Tony McKahan from Armbian > - where they apply a similar patch. Tony was going to test the patch, > but we have heard nothing back. The patch has been tested on ArchLinux > Arm, and found to work. Apologies, I've got too many things going at once, and it sounded like there would/should be a V2 of this patch. I tested it against 5.0 rc8 with sd-uhs-ddr50 removed as discussed previously, no issues encountered. Tony > > So with no further comments, I propose this is accepted as is. Heiko, > let me know if you want me to respin this patch to apply cleanly after > the sd card changes. > > David. > > > > On 17/02/2019 12:15, David Summers wrote: > > This patch adds the wifi to the ASUS Tinker Board (S) machines. > > > > Unfortunatly neither the Tinker Board nor the Tinker Board S schematic > > indicate how the WiFi is wired up on these devices. The WiFi is > > provided by the RTL8723BS device, that has sdio WiFi and UART > > Bluetooth. This patch just adds the WiFi interface. > > > > With no schematic, most of the wiring has been derived from the ASUS > > patch to Debian: > > > > https://github.com/TinkerBoard/debian_kernel/commit/6a3128ade33f758887048578ada61a4b7ab8e678 > > > > In conjunction with the pin out of the RTL8723BS device: > > > > http://files.pine64.org/doc/datasheet/pine64/RTL8723BS.pdf > > http://cit.odessa.ua/media/pdf/Intel-Compute-Stick/FN-Link_F23BDSM25-W1.pdf > > > > The only unusual part is that to bring the card up, both the pins > > RK_PD3 and RK_PD4 need to be pulled. Why this needs to be done is not > > clear, best explaination is that they are connected to the RTL8723BS > > pins WL_DIS# and BT_DIS#, which the data sheet vaguely says: > > > > Shared with GPIO9 This Pin Can Externally Shutdown the RTL8723BS WLAN > > function when BT_DISn is Pulled Low. When this pin deasserted, SDIO > > interface will be disabled. This pin can also support the WLAN Ra > > dio-off function with host interface remaining connected. > > > > Anyway extensive testing the TheSaint on ArchLinux Arm Forum > > > > https://archlinuxarm.org/forum/viewtopic.php?f=44&t=13064&start=120#p60548 > > > > Signed-off-by: David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx> > > Signed-off-by: Stefan Wahren <stefan.wahren@xxxxxxxx> > > --- > > arch/arm/boot/dts/rk3288-tinker.dtsi | 39 +++++++++++++++++++++++++--- > > 1 file changed, 36 insertions(+), 3 deletions(-) > > > > diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi > > index fceaeed44e34..e1796f340eef 100644 > > --- a/arch/arm/boot/dts/rk3288-tinker.dtsi > > +++ b/arch/arm/boot/dts/rk3288-tinker.dtsi > > @@ -3,8 +3,9 @@ > > * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd. > > */ > > > > #include "rk3288.dtsi" > > #include <dt-bindings/input/input.h> > > +#include <dt-bindings/clock/rockchip,rk808.h> > > > > / { > > chosen { > > @@ -98,6 +97,15 @@ > > startup-delay-us = <100000>; > > vin-supply = <&vcc_io>; > > }; > > + > > + sdio_pwrseq: sdio-pwrseq { > > + compatible = "mmc-pwrseq-simple"; > > + clocks = <&rk808 RK808_CLKOUT1>; > > + clock-names = "ext_clock"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&wifi_enable>; > > + reset-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_LOW>, <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>; > > + }; > > }; > > > > &cpu0 { > > @@ -337,8 +345,8 @@ > > > > &io_domains { > > status = "okay"; > > - > > sdcard-supply = <&vccio_sd>; > > + wifi-supply = <&vcc_18>; > > }; > > > > &pinctrl { > > @@ -417,6 +425,12 @@ > > rockchip,pins = <7 8 RK_FUNC_GPIO &pcfg_pull_none>; > > }; > > }; > > + > > + sdio { > > + wifi_enable: wifi-enable { > > + rockchip,pins = <4 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>, <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>; > > + }; > > + }; > > }; > > > > &pwm0 { > > @@ -440,6 +454,25 @@ > > vqmmc-supply = <&vccio_sd>; > > }; > > > > +&sdio0 { > > + bus-width = <4>; > > + cap-sd-highspeed; > > + cap-sdio-irq; > > + keep-power-in-suspend; > > + mmc-pwrseq = <&sdio_pwrseq>; > > + non-removable; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&sdio0_bus4>, <&sdio0_cmd>, <&sdio0_clk>, <&sdio0_int>; > > + max-frequency = <50000000>; > > + sd-uhs-sdr12; > > + sd-uhs-sdr25; > > + sd-uhs-sdr50; > > + sd-uhs-ddr50; > > + vmmc-supply = <&vcc_io>; > > + vqmmc-supply = <&vcc_18>; > > + status = "okay"; > > +}; > > + > > &tsadc { > > rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */ > > rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */ > > _______________________________________________ Linux-rockchip mailing list Linux-rockchip@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/linux-rockchip
